Maria-Andreea Lungan
Maria-Andreea Lungan has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Marcel Popa
Faculty of Chemical Engineering and Environmental Protection “Cristofor Simionescu”, Department of Natural and Synthetic Polymers, “Gheorghe Asachi” Technical University, Bd. D. Mangeron, nr. 73, 700050 Iaşi, Romania
6 shared publications - Stefania Racovita
“Petru Poni” Institute of Macromolecular Chemistry, Grigore Ghica Voda Alley, No. 41A, 700487 Iasi, Romania
5 shared publications - Silvia Vasiliu
“Petru Poni” Institute of Macromolecular Chemistry, Grigore Ghica Voda Alley, No. 41A, 700487 Iasi, Romania
4 shared publications - Jacques Desbrieres
University of Pau and Adour Countries (UPPA), IPREM, Hélioparc Pau Pyrénées, Pau, France
3 shared publications - Adrian Bărbatu
SARA Pharm Solutions S.R.L, Bucharest-5, Romania
2 shared publications - Corina-Mihaela Manta
Sara Pharm Solutions S.R.L., 266-268 Calea Rahovei, 050912 Bucharest, Romania
2 shared publications
Latest Publications
- 3 October 2021
- Published by Taylor & Francis in Drug Development and Industrial Pharmacy
- Vol. 47 (10) , 1598-1606
Physico-chemical properties of two anhydrous azathioprine forms and their interaction with typical pharmaceutical excipients: highlighting new findings in drug formulation development
The physico-chemical properties of two anhydrous AZA forms and their interaction with typical pharmaceutical excipients were assessed by applying various methods (such as PXRD, HPLC, TG/DSC, IR, Raman, PL or UV-Vis) in order to highlight new directions for drug formulation. The stability assessment of AZA anhydrous forms I and II was performed in order to determine the risk of degradation of the active ingredient by accidental exposure to non-standard conditions in the industrial environment, under different storage, transport or processing conditions. The benefits of form II include increased resistance to chemical degradation over a wide range of pH, but further control of storage and processing conditions is necessary to avoid polymorphic transformation into form I. The solubility assessment on the AZA solid forms in different environments that simulate the conditions of the gastrointestinal tract has the advantage of a significantly increased solubility of form II compared with the commercial form I due to the modification of the crystalline structure. In the case of capsules compared to AZA form I or II as powder, an improvement in their solubility was observed, promoted by the presence of one or more excipients in the formulation mixture.
- 3 October 2021
- Published by Taylor & Francis in Drug Development and Industrial Pharmacy
- Vol. 47 (10) , 1598-1606
Physico-chemical properties of two anhydrous azathioprine forms and their interaction with typical pharmaceutical excipients: highlighting new findings in drug formulation development
The physico-chemical properties of two anhydrous AZA forms and their interaction with typical pharmaceutical excipients were assessed by applying various methods (such as PXRD, HPLC, TG/DSC, IR, Raman, PL or UV-Vis) in order to highlight new directions for drug formulation. The stability assessment of AZA anhydrous forms I and II was performed in order to determine the risk of degradation of the active ingredient by accidental exposure to non-standard conditions in the industrial environment, under different storage, transport or processing conditions. The benefits of form II include increased resistance to chemical degradation over a wide range of pH, but further control of storage and processing conditions is necessary to avoid polymorphic transformation into form I. The solubility assessment on the AZA solid forms in different environments that simulate the conditions of the gastrointestinal tract has the advantage of a significantly increased solubility of form II compared with the commercial form I due to the modification of the crystalline structure. In the case of capsules compared to AZA form I or II as powder, an improvement in their solubility was observed, promoted by the presence of one or more excipients in the formulation mixture.
- 29 July 2021
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 21 (9) , 4837-4846
Isomorphic Channel-Type Pseudopolymorphs of Azathioprine: From Structural Confirmations to a Rational Polymorph Screening Approach
- 29 July 2021
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 21 (9) , 4837-4846
Isomorphic Channel-Type Pseudopolymorphs of Azathioprine: From Structural Confirmations to a Rational Polymorph Screening Approach
- Top Cited PapersOpen Access
- 4 March 2021
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 22 (5) , 2585
The Benefits of Smart Nanoparticles in Dental Applications
Dentistry, as a branch of medicine, has undergone continuous evolution over time. The scientific world has focused its attention on the development of new methods and materials with improved properties that meet the needs of patients. For this purpose, the replacement of so-called “passive” dental materials that do not interact with the oral environment with “smart/intelligent” materials that have the capability to change their shape, color, or size in response to an externally stimulus, such as the temperature, pH, light, moisture, stress, electric or magnetic fields, and chemical compounds, has received much attention in recent years. A strong trend in dental applications is to apply nanotechnology and smart nanomaterials such as nanoclays, nanofibers, nanocomposites, nanobubbles, nanocapsules, solid-lipid nanoparticles, nanospheres, metallic nanoparticles, nanotubes, and nanocrystals. Among the nanomaterials, the smart nanoparticles present several advantages compared to other materials, creating the possibility to use them in various dental applications, including preventive dentistry, endodontics, restoration, and periodontal diseases. This review is focused on the recent developments and dental applications (drug delivery systems and restoration materials) of smart nanoparticles.
- 4 March 2021
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 22 (5) , 2585
Top Cited PapersOpen AccessThe Benefits of Smart Nanoparticles in Dental Applications
Dentistry, as a branch of medicine, has undergone continuous evolution over time. The scientific world has focused its attention on the development of new methods and materials with improved properties that meet the needs of patients. For this purpose, the replacement of so-called “passive” dental materials that do not interact with the oral environment with “smart/intelligent” materials that have the capability to change their shape, color, or size in response to an externally stimulus, such as the temperature, pH, light, moisture, stress, electric or magnetic fields, and chemical compounds, has received much attention in recent years. A strong trend in dental applications is to apply nanotechnology and smart nanomaterials such as nanoclays, nanofibers, nanocomposites, nanobubbles, nanocapsules, solid-lipid nanoparticles, nanospheres, metallic nanoparticles, nanotubes, and nanocrystals. Among the nanomaterials, the smart nanoparticles present several advantages compared to other materials, creating the possibility to use them in various dental applications, including preventive dentistry, endodontics, restoration, and periodontal diseases. This review is focused on the recent developments and dental applications (drug delivery systems and restoration materials) of smart nanoparticles.
- 10 September 2019
- Published by Wiley in Polymer International
- Vol. 69 (11) , 1066-1080
Porous microparticles based on methacrylic copolymers and gellan as drug delivery systems
Two types of porous microparticles based on glycidyl methacrylate, dimethacrylic monomers (ethylene glycol dimethacrylate, diethylene glycol dimethacrylate and triethylene glycol dimethacrylate) and gellan were prepared by two methods. The first method was aqueous suspension polymerization in the presence of N‐butyl acetate as porogenic agent when the crosslinking and grafting reactions were achieved in a single step. The second method was based on the reaction between hydroxyl groups belonging to gellan and the epoxy groups situated on the surface of porous microparticles based on glycidyl methacrylate and dimethacrylic monomers in basic medium. The microparticles with and without gellan were characterized by Fourier transform infrared spectroscopy, SEM, AFM and TGA. Also, the porous structure was investigated in terms of pore volume, porosity and specific surface. The swelling behaviour in aqueous solution with different pH values as well as sorption studies of cefuroxime sodium salt onto porous microparticles were investigated. The presence of gellan in the structure of the microparticles leads to porous materials characterized by higher specific surface areas (Ssp = 78–140 m2 g–1), higher swelling capacities (Sw = 162%–365%) and higher sorption capacities of the drug (qe = 101–147 mg g–1) compared to microparticles without gellan in their structures (Ssp = 73–85 m2 g–1; Sw = 139%–209%; qe = 70–110 mg g–1). © 2019 Society of Chemical Industry
- 10 September 2019
- Published by Wiley in Polymer International
- Vol. 69 (11) , 1066-1080
Porous microparticles based on methacrylic copolymers and gellan as drug delivery systems
Two types of porous microparticles based on glycidyl methacrylate, dimethacrylic monomers (ethylene glycol dimethacrylate, diethylene glycol dimethacrylate and triethylene glycol dimethacrylate) and gellan were prepared by two methods. The first method was aqueous suspension polymerization in the presence of N‐butyl acetate as porogenic agent when the crosslinking and grafting reactions were achieved in a single step. The second method was based on the reaction between hydroxyl groups belonging to gellan and the epoxy groups situated on the surface of porous microparticles based on glycidyl methacrylate and dimethacrylic monomers in basic medium. The microparticles with and without gellan were characterized by Fourier transform infrared spectroscopy, SEM, AFM and TGA. Also, the porous structure was investigated in terms of pore volume, porosity and specific surface. The swelling behaviour in aqueous solution with different pH values as well as sorption studies of cefuroxime sodium salt onto porous microparticles were investigated. The presence of gellan in the structure of the microparticles leads to porous materials characterized by higher specific surface areas (Ssp = 78–140 m2 g–1), higher swelling capacities (Sw = 162%–365%) and higher sorption capacities of the drug (qe = 101–147 mg g–1) compared to microparticles without gellan in their structures (Ssp = 73–85 m2 g–1; Sw = 139%–209%; qe = 70–110 mg g–1). © 2019 Society of Chemical Industry
- 26 August 2019
- Published by Wiley in ChemistrySelect
- Vol. 4 (32) , 9331-9338
Design of Porous Microparticles Based on Chitosan and Methacrylic Monomers
Starting from glycidyl methacrylate, three dimethacrylic monomers (mono, di and triethylene glycol dimethacrylate) and chitosan, various types of porous microparticles were obtained by suspension polymerization technique. Also, using the same technique the un‐grafted porous microparticles were obtained by reaction between glycidyl methacrylate and dimethacrylic monomers. The successful grafting reaction of chitosan onto synthetic polymer networks was highlighted by FTIR spectroscopy, scanning electron microscopy, atomic force microscopy and thermogravimetric analysis. The dimensional analysis of all type of microparticles was performed by laser diffraction while the specific surface areas were determined by means of dynamic vapor sorption. Grafting of polysaccharide onto crosslinked networks has led to the preparation of polymeric materials with high specific surface area (50‐160 m 2 /g) and better swelling capacities (101‐106%) compared to microparticles based on glycidyl methacrylate and dimethacrylic monomers [(31‐69 m 2 /g) and (39‐57%), respectively]. Furthermore, the sorption properties of grafted and un‐grafted microparticles were tested using Cu(II) solution. The highest retention capacity value of Cu(II) (41.7 mg/g) was obtained when the C 1 microparticles were used in the adsorption studies.
- 26 August 2019
- Published by Wiley in ChemistrySelect
- Vol. 4 (32) , 9331-9338
Design of Porous Microparticles Based on Chitosan and Methacrylic Monomers
Starting from glycidyl methacrylate, three dimethacrylic monomers (mono, di and triethylene glycol dimethacrylate) and chitosan, various types of porous microparticles were obtained by suspension polymerization technique. Also, using the same technique the un‐grafted porous microparticles were obtained by reaction between glycidyl methacrylate and dimethacrylic monomers. The successful grafting reaction of chitosan onto synthetic polymer networks was highlighted by FTIR spectroscopy, scanning electron microscopy, atomic force microscopy and thermogravimetric analysis. The dimensional analysis of all type of microparticles was performed by laser diffraction while the specific surface areas were determined by means of dynamic vapor sorption. Grafting of polysaccharide onto crosslinked networks has led to the preparation of polymeric materials with high specific surface area (50‐160 m 2 /g) and better swelling capacities (101‐106%) compared to microparticles based on glycidyl methacrylate and dimethacrylic monomers [(31‐69 m 2 /g) and (39‐57%), respectively]. Furthermore, the sorption properties of grafted and un‐grafted microparticles were tested using Cu(II) solution. The highest retention capacity value of Cu(II) (41.7 mg/g) was obtained when the C 1 microparticles were used in the adsorption studies.
- 1 November 2016
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 92, 561-572
New hybrid magnetic nanoparticles based on chitosan-maltose derivative for antitumor drug delivery
- 1 November 2016
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 92, 561-572
New hybrid magnetic nanoparticles based on chitosan-maltose derivative for antitumor drug delivery
- 1 August 2016
- Published by Elsevier in Reactive and Functional Polymers
- Vol. 105, 103-113
Adsorption and release studies of cefuroxime sodium from acrylic ion exchange resin microparticles coated with gellan
- 1 August 2016
- Published by Elsevier in Reactive and Functional Polymers
- Vol. 105, 103-113
Adsorption and release studies of cefuroxime sodium from acrylic ion exchange resin microparticles coated with gellan
- 10 October 2015
- Published by Wiley
- p. 467-502
Ion Exchangers – An Open Window for the Development of Advanced Materials with Pharmaceutical and Medical Applications
- 10 October 2015
- Published by Wiley
- p. 467-502
Ion Exchangers – An Open Window for the Development of Advanced Materials with Pharmaceutical and Medical Applications
- 1 July 2015
- Published by Elsevier in Carbohydrate Polymers
- Vol. 125, 323-333
Surface characterization and drug release from porous microparticles based on methacrylic monomers and xanthan
- 1 July 2015
- Published by Elsevier in Carbohydrate Polymers
- Vol. 125, 323-333
Surface characterization and drug release from porous microparticles based on methacrylic monomers and xanthan
- 1 April 2014
- Published by Elsevier in Carbohydrate Polymers
- Vol. 104, 213-222
Complex microparticulate systems based on glycidyl methacrylate and xanthan
- 1 April 2014
- Published by Elsevier in Carbohydrate Polymers
- Vol. 104, 213-222
Complex microparticulate systems based on glycidyl methacrylate and xanthan