William Hearn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
William Hearn has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
Eduard Hryha
4 shared publications- Andaç Özsoy
Laboratory for Condensed Matter, PSI Center for Photon Science
3 shared publications Roland E. Logé
3 shared publicationsSteve Gaudez
3 shared publications- Steven Van Petegem
Paul Scherrer Institute
3 shared publications Alexander Rack
2 shared publications
Latest Publications
- Open Access
- 4 March 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 121
Dynamics of material redistribution and microstructure formation in Al–Cu multimaterial
- 4 March 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 121
Open AccessDynamics of material redistribution and microstructure formation in Al–Cu multimaterial
- Open Access
- 28 December 2025
- Published by Elsevier in Optics & Laser Technology
- Vol. 195
Exploring real-time monitoring of laser-induced recrystallization using acoustic emissions
- 28 December 2025
- Published by Elsevier in Optics & Laser Technology
- Vol. 195
Open AccessExploring real-time monitoring of laser-induced recrystallization using acoustic emissions
- Open Access
- 9 November 2025
- Published by Elsevier in Additive Manufacturing
- Vol. 113
Phase transformations in hypoeutectoid carbon steel during laser powder bed fusion
- 9 November 2025
- Published by Elsevier in Additive Manufacturing
- Vol. 113
Open AccessPhase transformations in hypoeutectoid carbon steel during laser powder bed fusion
- Open Access
- 31 August 2025
- Published by Elsevier in Additive Manufacturing
- Vol. 110
Phase-separation-driven cracking in additive manufacturing of Ni-Cu alloy systems
- 31 August 2025
- Published by Elsevier in Additive Manufacturing
- Vol. 110
Open AccessPhase-separation-driven cracking in additive manufacturing of Ni-Cu alloy systems
- Open Access
- 10 July 2025
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 20 (1)
Deconvoluting cracking mechanisms in fusion processing of steel-copper multi-materials via Operando X-ray characterisation
- 10 July 2025
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 20 (1)
Open AccessDeconvoluting cracking mechanisms in fusion processing of steel-copper multi-materials via Operando X-ray characterisation
- Open Access
- 27 June 2024
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 57 (4) , 986-1000
X-ray tensor tomography for small-grained polycrystals with strong texture
Small-angle X-ray tensor tomography and the related wide-angle X-ray tensor tomography are X-ray imaging techniques that tomographically reconstruct the anisotropic scattering density of extended samples. In previous studies, these methods have been used to image samples where the scattering density depends slowly on the direction of scattering, typically modeling the directionality, i.e. the texture, with a spherical harmonics expansion up until order ℓ = 8 or lower. This study investigates the performance of several established algorithms from small-angle X-ray tensor tomography on samples with a faster variation as a function of scattering direction and compares their expected and achieved performance. The various algorithms are tested using wide-angle scattering data from an as-drawn steel wire with known texture to establish the viability of the tensor tomography approach for such samples and to compare the performance of existing algorithms.
- 27 June 2024
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 57 (4) , 986-1000
Open AccessX-ray tensor tomography for small-grained polycrystals with strong texture
Small-angle X-ray tensor tomography and the related wide-angle X-ray tensor tomography are X-ray imaging techniques that tomographically reconstruct the anisotropic scattering density of extended samples. In previous studies, these methods have been used to image samples where the scattering density depends slowly on the direction of scattering, typically modeling the directionality, i.e. the texture, with a spherical harmonics expansion up until order ℓ = 8 or lower. This study investigates the performance of several established algorithms from small-angle X-ray tensor tomography on samples with a faster variation as a function of scattering direction and compares their expected and achieved performance. The various algorithms are tested using wide-angle scattering data from an as-drawn steel wire with known texture to establish the viability of the tensor tomography approach for such samples and to compare the performance of existing algorithms.
- Open Access
- 6 October 2023
- Published by Elsevier in Powder Technology
- Vol. 431, 119046
Impact of powder properties on deoxidation and densification of carbon steels during powder bed fusion – Laser beam
- 6 October 2023
- Published by Elsevier in Powder Technology
- Vol. 431, 119046
Open AccessImpact of powder properties on deoxidation and densification of carbon steels during powder bed fusion – Laser beam
- Open Access
- 17 October 2022
- Published by SAGE Publications in Powder Metallurgy
- Vol. 66 (2) , 94-106
Development of powder bed fusion – laser beam process for AISI 4140, 4340 and 8620 low-alloy steel
This study focuses on process development and mechanical property evaluation of AISI 4140, 4340 and 8620 low-alloy steel produced by powder bed fusion – laser beam (PBF-LB). Process development found that increasing the build plate preheating temperature to 180°C improved processability, as it mitigated lack of fusion and cold cracking defects. Subsequent mechanical testing found that the low-alloy steels achieved a high ultimate tensile strength (4140:∼1400 MPa, 4340:∼1500 MPa, 8620:∼1100 MPa), impact toughness (4140:∼90–100 J, 4340:∼60–70 J, 8620:∼150–175 J) and elongation (4140:∼14%, 4340:∼14%, 8620:∼14–15%) that met or exceeded the ASTM standards. Mechanical testing also revealed limited directional anisotropy that was attributed to low levels of internal defects (< 0.1%), small grains with weak crystallographic texture and improved tempering due to build plate preheating and post PBF-LB stress relief. This indicates that with adequate process development, low-alloy steels produced by PBF-LB can meet or exceed the performance of conventionally produced alloys.
- 17 October 2022
- Published by SAGE Publications in Powder Metallurgy
- Vol. 66 (2) , 94-106
Open AccessDevelopment of powder bed fusion – laser beam process for AISI 4140, 4340 and 8620 low-alloy steel
This study focuses on process development and mechanical property evaluation of AISI 4140, 4340 and 8620 low-alloy steel produced by powder bed fusion – laser beam (PBF-LB). Process development found that increasing the build plate preheating temperature to 180°C improved processability, as it mitigated lack of fusion and cold cracking defects. Subsequent mechanical testing found that the low-alloy steels achieved a high ultimate tensile strength (4140:∼1400 MPa, 4340:∼1500 MPa, 8620:∼1100 MPa), impact toughness (4140:∼90–100 J, 4340:∼60–70 J, 8620:∼150–175 J) and elongation (4140:∼14%, 4340:∼14%, 8620:∼14–15%) that met or exceeded the ASTM standards. Mechanical testing also revealed limited directional anisotropy that was attributed to low levels of internal defects (< 0.1%), small grains with weak crystallographic texture and improved tempering due to build plate preheating and post PBF-LB stress relief. This indicates that with adequate process development, low-alloy steels produced by PBF-LB can meet or exceed the performance of conventionally produced alloys.
- Open Access
- 19 May 2022
- Published by Elsevier in Materialia
- Vol. 23
In situ tempering of martensite during laser powder bed fusion of Fe-0.45C steel
- 19 May 2022
- Published by Elsevier in Materialia
- Vol. 23
Open AccessIn situ tempering of martensite during laser powder bed fusion of Fe-0.45C steel
- Open Access
- 3 January 2022
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 8
Effect of Carbon Content on the Processability of Fe-C Alloys Produced by Laser Based Powder Bed Fusion
The present study examines the processability of Fe-C alloys, with carbon contents up to 1.1 wt%, when using laser based powder bed fusion (LB-PBF). Analysis of specimen cross-sections revealed that lack of fusion porosity was prominent in specimens produced at low volumetric energy density (VED), while keyhole porosity was prominent in specimens produced at high VED. The formation of porosity was also influenced by the carbon content, where increasing the carbon content reduced lack of fusion porosity, while simultaneously increasing the susceptibility to form keyhole porosity. These trends were related to an improved wettability, viscosity, and flow of the melt pool as well an increased melt pool depth as the carbon content increased. Cold cracking defects were also observed in Fe-C alloys that had an as-built hardness ≥425 HV. Reducing the carbon content below 0.75 wt% and increasing the VED, which improved the intrinsic heat treatment during LB-PBF, were found to be effective mitigation strategies to avoid cold cracking defects. Based upon these results, a process window for the Fe-C system was established that produces high density (>99.8%), defect-free specimens via LB-PBF without the requirement of build plate preheating.
- 3 January 2022
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 8
Open AccessEffect of Carbon Content on the Processability of Fe-C Alloys Produced by Laser Based Powder Bed Fusion
The present study examines the processability of Fe-C alloys, with carbon contents up to 1.1 wt%, when using laser based powder bed fusion (LB-PBF). Analysis of specimen cross-sections revealed that lack of fusion porosity was prominent in specimens produced at low volumetric energy density (VED), while keyhole porosity was prominent in specimens produced at high VED. The formation of porosity was also influenced by the carbon content, where increasing the carbon content reduced lack of fusion porosity, while simultaneously increasing the susceptibility to form keyhole porosity. These trends were related to an improved wettability, viscosity, and flow of the melt pool as well an increased melt pool depth as the carbon content increased. Cold cracking defects were also observed in Fe-C alloys that had an as-built hardness ≥425 HV. Reducing the carbon content below 0.75 wt% and increasing the VED, which improved the intrinsic heat treatment during LB-PBF, were found to be effective mitigation strategies to avoid cold cracking defects. Based upon these results, a process window for the Fe-C system was established that produces high density (>99.8%), defect-free specimens via LB-PBF without the requirement of build plate preheating.