Ahmad Abu-Jrai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmad Abu-Jrai has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Ramadan Gomaa
Al-Hussein Bin Talal University
2 shared publications - Abdullah Marashli
Mechanical Engineering Department, Faculty of Engineering, Al-Hussein Bin Talal University, Ma’an 71111, Jordan
1 shared publication - Ahmad O. Hasan
Department of Mechanical Engineering, Faculty of Engineering, Al-Hussein Bin Talal University, Ma’an 71110, Jordan
1 shared publication - Hani Al-Rawashdeh
Mechanical Engineering Department, Faculty of Engineering, Al-Hussein Bin Talal University, Ma’an 71111, Jordan
1 shared publication - Hegazy Rezk
Department of Electrical Engineering, College of Engineering in Wadi Alddawasir, Prince Sattam bin Abdulaziz University, Al-Kharj, Saudi Arabia
1 shared publication - Moath A. Altarawneh
Lafarge Jordan Cement, Rashadiya 25111, Jordan
1 shared publication
Latest Publications
- Open Access
Determination of Carbonyls Compound, Ketones and Aldehydes Emissions from CI Diesel Engines Fueled with Pure Diesel/Diesel Methanol Blends
Quantitative and qualitative analyses of chemical species out of CI engine tailpipe emissions fueled with pure diesel and diesel methanol blends, trapped in dinitro phenylhydrazine (DNPH) solutions, were performed. The formed hydrazine was studied using high-performance liquid chromatography (HPLC) accompanied by a detector for ultraviolet (UV). A set of carbonyl-DNPH derivative standards was developed and compared with engine tailpipe gases produced by both fuel modes. An understanding of carbonyl chemical compounds such as formaldehyde, acetaldehyde, and acrolein (HCHO, CH3CHO, and H2 = CHCHO, respectively) is essential for researchers to know how these chemicals affect human health and the environment. In both fuel modes, acetaldehyde was the main combustible product 25 ppm followed by formaldehyde 17 ppm, croton aldehydes 16 ppm, acrolein 12 ppm, and iso-valerdyhyde 10 ppm. In addition to these species, only a few other chemical species were detected in the exhaust gas. According to this study, carbonyl compounds from blended fuel contribute 15–22% of pure diesel fuel emissions. As shown by the results, engine operating conditions and fuel mode have a strong impact on the total amount of carbonyls released by the engine. Engine performance was highly influenced by different fuel modes and engine speeds. Using pure diesel, the regulated emissions, HC, CO, and NOx, registered high concentrations at a lower speed (1500 rpm) and NOx presented with the highest concentration of 4 g/kWh followed by CO with 1 g/kWh and HC with 0.5 g/kWh.
Open AccessDetermination of Carbonyls Compound, Ketones and Aldehydes Emissions from CI Diesel Engines Fueled with Pure Diesel/Diesel Methanol Blends
Quantitative and qualitative analyses of chemical species out of CI engine tailpipe emissions fueled with pure diesel and diesel methanol blends, trapped in dinitro phenylhydrazine (DNPH) solutions, were performed. The formed hydrazine was studied using high-performance liquid chromatography (HPLC) accompanied by a detector for ultraviolet (UV). A set of carbonyl-DNPH derivative standards was developed and compared with engine tailpipe gases produced by both fuel modes. An understanding of carbonyl chemical compounds such as formaldehyde, acetaldehyde, and acrolein (HCHO, CH3CHO, and H2 = CHCHO, respectively) is essential for researchers to know how these chemicals affect human health and the environment. In both fuel modes, acetaldehyde was the main combustible product 25 ppm followed by formaldehyde 17 ppm, croton aldehydes 16 ppm, acrolein 12 ppm, and iso-valerdyhyde 10 ppm. In addition to these species, only a few other chemical species were detected in the exhaust gas. According to this study, carbonyl compounds from blended fuel contribute 15–22% of pure diesel fuel emissions. As shown by the results, engine operating conditions and fuel mode have a strong impact on the total amount of carbonyls released by the engine. Engine performance was highly influenced by different fuel modes and engine speeds. Using pure diesel, the regulated emissions, HC, CO, and NOx, registered high concentrations at a lower speed (1500 rpm) and NOx presented with the highest concentration of 4 g/kWh followed by CO with 1 g/kWh and HC with 0.5 g/kWh.
- Open Access
- 16 August 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (16) , 10146
Experimental Investigation on Waste Heat Recovery from a Cement Factory to Enhance Thermoelectric Generation
This work investigated the potential for waste heat recovery from a cement factory using thermoelectric generation (TEG) technology. Several TEGs were placed on a secondary coaxial shell separated from the kiln shell by an air gap. The performance of the system was tested and evaluated experimentally. Two cooling methods, active water and forced air, were considered. A forced closed-loop water cooling system with a heat exchanger was considered for the active-water cooling method. A heat exchanger was inserted before the water tank to improve cooling efficiency by reducing the inlet temperature of the cooling water tank, in contrast to forced-air cooling, in which a heatsink was used. The obtained results indicated that the closed-loop water-cooled system equipped with a radiator, i.e., active water, has the highest conversion efficiency. The maximum absorbed heat for the forced-air and active-water cooling systems were 265.03 and 262.95 W, respectively. The active-water cooling method improves the power of TEG by 4.4% in comparison with forced-air cooling, while the payback periods for the proposed active-water and forced-air cooling systems are approximately 16 and 9 months, respectively.
- 16 August 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (16) , 10146
Open AccessExperimental Investigation on Waste Heat Recovery from a Cement Factory to Enhance Thermoelectric Generation
This work investigated the potential for waste heat recovery from a cement factory using thermoelectric generation (TEG) technology. Several TEGs were placed on a secondary coaxial shell separated from the kiln shell by an air gap. The performance of the system was tested and evaluated experimentally. Two cooling methods, active water and forced air, were considered. A forced closed-loop water cooling system with a heat exchanger was considered for the active-water cooling method. A heat exchanger was inserted before the water tank to improve cooling efficiency by reducing the inlet temperature of the cooling water tank, in contrast to forced-air cooling, in which a heatsink was used. The obtained results indicated that the closed-loop water-cooled system equipped with a radiator, i.e., active water, has the highest conversion efficiency. The maximum absorbed heat for the forced-air and active-water cooling systems were 265.03 and 262.95 W, respectively. The active-water cooling method improves the power of TEG by 4.4% in comparison with forced-air cooling, while the payback periods for the proposed active-water and forced-air cooling systems are approximately 16 and 9 months, respectively.