Young Sup Choi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Young Sup Choi has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Kang Il Lee
Institute of Plasma Technology, Korea Institute of Fusion Energy, 37 Dongjangsan-ro, Gunsan-si 54004, Jeollabuk-do, Korea
2 shared publications - Dong Chan Seok
Institute of Plasma Technology, Korea Institute of Fusion Energy 1 , Gunsan 54004
1 shared publication - Hyun Jong You
Institute of Plasma Technology, Korea Institute of Fusion Energy, 37 Dongjangsan-ro, Gunsan-si 54004, Jeollabuk-do, Korea
1 shared publication - Hyunjae Park
Institute of Plasma Technology and the Korea Institute of Fusion Energy, Gunsan, South Korea
1 shared publication - Jin-Ha Shin
Institute of Plasma Technology, 814-2 Osickdo-dong, Gunsan 573-540, Jeollabuk-do, Korea
1 shared publication - Seung Pyo Hong
Institute of Plasma Technology, Korea Institute of Fusion Energy, 37 Dongjangsan-ro, Gunsan-si 54004, Jeollabuk-do, Korea
1 shared publication
Latest Publications
- Open Access
- 8 June 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (12) , 1959
Scanning Deposition Method for Large-Area Diamond Film Synthesis Using Multiple Microwave Plasma Sources
The demand for synthetic diamonds and research on their use in next-generation semiconductor devices have recently increased. Microwave plasma chemical vapor deposition (MPCVD) is considered one of the most promising techniques for the mass production of large-sized and high-quality single-, micro- and nanocrystalline diamond films. Although the low-pressure resonant cavity MPCVD method can synthesize high-quality diamonds, improvements are needed in terms of the resulting area. In this study, a large-area diamond synthesis method was developed by arranging several point plasma sources capable of processing a small area and scanning a wafer. A unit combination of three plasma sources afforded a diamond film thickness uniformity of ±6.25% at a wafer width of 70 mm with a power of 700 W for each plasma source. Even distribution of the diamond grains in a size range of 0.1–1 μm on the thin-film surface was verified using field-emission scanning electron microscopy. Therefore, the proposed novel diamond synthesis method can be theoretically expanded to achieve large-area films.
- 8 June 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (12) , 1959
Open AccessScanning Deposition Method for Large-Area Diamond Film Synthesis Using Multiple Microwave Plasma Sources
The demand for synthetic diamonds and research on their use in next-generation semiconductor devices have recently increased. Microwave plasma chemical vapor deposition (MPCVD) is considered one of the most promising techniques for the mass production of large-sized and high-quality single-, micro- and nanocrystalline diamond films. Although the low-pressure resonant cavity MPCVD method can synthesize high-quality diamonds, improvements are needed in terms of the resulting area. In this study, a large-area diamond synthesis method was developed by arranging several point plasma sources capable of processing a small area and scanning a wafer. A unit combination of three plasma sources afforded a diamond film thickness uniformity of ±6.25% at a wafer width of 70 mm with a power of 700 W for each plasma source. Even distribution of the diamond grains in a size range of 0.1–1 μm on the thin-film surface was verified using field-emission scanning electron microscopy. Therefore, the proposed novel diamond synthesis method can be theoretically expanded to achieve large-area films.
- Open Access
- 13 April 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (8) , 1338
Remote Plasma-Induced Synthesis of Self-Assembled MoS2/Carbon Nanowall Nanocomposites and Their Application as High-Performance Active Materials for Supercapacitors
The objective of this study is to investigate the synthesis and influence of MoS2 on carbon nanowalls (CNWs) as supercapacitor electrodes. The synthesis of MoS2 on CNW was achieved by the introduction of hydrogen remote plasma from ammonium tetrathiomolybdate (ATTM) without deterioration of the CNWs. The topographical surface structures and electrochemical characteristics of the MoS2–CNW composite electrodes were explored using two ATTM-dispersed organic solvents—acetonitrile and dimethylformamide (DMF). In this study, CNW and MoS2 were synthesized using an electron cyclotron resonance plasma. However, hydrogen radicals, which transform ATTM into MoS2, were provided in the form of a remote plasma source. The electrochemical performances of MoS2–CNW hybrid electrodes with various morphologies—depending on the solvent and ATTM concentration—were evaluated using a three-electrode system. The results revealed that the morphology of the synthesized MoS2 was influenced by the organic solvent used and affected both the electrochemical performance and topographical characteristics. Notably, considerable enhancement of the specific capacitance was observed for the MoS2 with open top edges synthesized from DMF. These encouraging results may motivate additional research on hybrid supercapacitor electrodes and the rapid synthesis of MoS2 and other transition metal dichalcogenides.
- 13 April 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (8) , 1338
Open AccessRemote Plasma-Induced Synthesis of Self-Assembled MoS2/Carbon Nanowall Nanocomposites and Their Application as High-Performance Active Materials for Supercapacitors
The objective of this study is to investigate the synthesis and influence of MoS2 on carbon nanowalls (CNWs) as supercapacitor electrodes. The synthesis of MoS2 on CNW was achieved by the introduction of hydrogen remote plasma from ammonium tetrathiomolybdate (ATTM) without deterioration of the CNWs. The topographical surface structures and electrochemical characteristics of the MoS2–CNW composite electrodes were explored using two ATTM-dispersed organic solvents—acetonitrile and dimethylformamide (DMF). In this study, CNW and MoS2 were synthesized using an electron cyclotron resonance plasma. However, hydrogen radicals, which transform ATTM into MoS2, were provided in the form of a remote plasma source. The electrochemical performances of MoS2–CNW hybrid electrodes with various morphologies—depending on the solvent and ATTM concentration—were evaluated using a three-electrode system. The results revealed that the morphology of the synthesized MoS2 was influenced by the organic solvent used and affected both the electrochemical performance and topographical characteristics. Notably, considerable enhancement of the specific capacitance was observed for the MoS2 with open top edges synthesized from DMF. These encouraging results may motivate additional research on hybrid supercapacitor electrodes and the rapid synthesis of MoS2 and other transition metal dichalcogenides.
- Open Access
Silicon Carbide Wafer Machining by Using a Single Filament Plasma at Atmospheric Pressure
SiC wafers were etched using a filament plasma of He:NF3:O2 (helium:nitrogen trifluoride:oxygen) mixed gas at atmospheric pressure. When 0.5–2 sccm of NF3 was mixed to 2 slm of He filament plasma, the etch depth and etch rate increased, but there was little change in the etch width as the NF3 mixing amount increased. The increment of the NF3 mixing also suppressed the surface roughening of plasma etching. The addition of O2 to the He-NF3 filament plasma slightly increased the SiC wafer etch rate. When the NF3 mixing amount was 2 sccm, the roughness of the etched surface increased sharply by O2 addition. On the contrary, the NF3 mixing amount was 1 sccm; the addition of O2 reduced the roughness more than that of the pristine. The roughness of the pristine SiC wafer specimens is in the range of Ra 0.7–0.8 nm. After 30 min of etching on a 6 mm by 6 mm square area, the roughness of the etched surface reduced to Ra 0.587 nm, while the etch rate was 2.74 μm/h with a He:NF3:O2 of 2:1:3 (slm:sccm:sccm) filament plasma and 3 mm/s speed of raster scan etch of the optimized roughening suppression etching recipe.
Open AccessSilicon Carbide Wafer Machining by Using a Single Filament Plasma at Atmospheric Pressure
SiC wafers were etched using a filament plasma of He:NF3:O2 (helium:nitrogen trifluoride:oxygen) mixed gas at atmospheric pressure. When 0.5–2 sccm of NF3 was mixed to 2 slm of He filament plasma, the etch depth and etch rate increased, but there was little change in the etch width as the NF3 mixing amount increased. The increment of the NF3 mixing also suppressed the surface roughening of plasma etching. The addition of O2 to the He-NF3 filament plasma slightly increased the SiC wafer etch rate. When the NF3 mixing amount was 2 sccm, the roughness of the etched surface increased sharply by O2 addition. On the contrary, the NF3 mixing amount was 1 sccm; the addition of O2 reduced the roughness more than that of the pristine. The roughness of the pristine SiC wafer specimens is in the range of Ra 0.7–0.8 nm. After 30 min of etching on a 6 mm by 6 mm square area, the roughness of the etched surface reduced to Ra 0.587 nm, while the etch rate was 2.74 μm/h with a He:NF3:O2 of 2:1:3 (slm:sccm:sccm) filament plasma and 3 mm/s speed of raster scan etch of the optimized roughening suppression etching recipe.