Cristiano José de Farias Braz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Cristiano José de Farias Braz has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Renata Barbosa
Postgraduate Program in Materials Science and Engineering Federal University of Piauí (UFPI) Teresina Piauí Brazil
5 shared publications - Tatianny Soares Alves
Postgraduate Program in Materials Science and Engineering Federal University of Piauí (UFPI) Teresina Piauí Brazil
5 shared publications - Albaniza Alves Tavares
Universidade Federal de Campina Grande, Brasil
2 shared publications - Alisson Rodrigues de Oliveira Dias
Universidade Federal do Ceará, Brasil
2 shared publications - Ana Carolina Ferreira dos Santos Rosa
Graduation in Materials Engineering, Technology Center Federal University of Piauí Teresina Brazil
2 shared publications - Laura Hecker de Carvalho
Universidade Federal de Campina Grande, Brasil
2 shared publications
Latest Publications
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 35 (1) , e20250012
Polypropylene reinforced with hollow glass microspheres: effect of thermal aging and reprocessing
The hollow glass microspheres (HGM), exhibit low density, reduced dielectric constant, and good thermal conductivity. This study assessed the mechanical performance of polypropylene (PP) reinforced with HGM under artificial thermal aging conditions. The compositions underwent two rounds of reprocessing in a single-screw extruder, and samples were prepared for both tensile and impact testing. Tensile specimens were subjected to thermal aging at 100 ºC for seven and 21 days. Mechanical tests were carried out on samples before and after aging, while exposed samples underwent visual inspection, optical microscopy, and Fourier transform infrared spectroscopy analysis. Visual inspection and microscopy revealed improved PP-HGM interaction due to the additives, with no deformation or damage from reprocessing. Infrared spectroscopy showed minor degradation in the PP structure post-exposure. In summary, the presence and content of HGM, reprocessing, and aging time significantly affect the mechanical properties (elastic modulus, breaking stress, elongation at break, and impact resistance).
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 35 (1) , e20250012
Open AccessPolypropylene reinforced with hollow glass microspheres: effect of thermal aging and reprocessing
The hollow glass microspheres (HGM), exhibit low density, reduced dielectric constant, and good thermal conductivity. This study assessed the mechanical performance of polypropylene (PP) reinforced with HGM under artificial thermal aging conditions. The compositions underwent two rounds of reprocessing in a single-screw extruder, and samples were prepared for both tensile and impact testing. Tensile specimens were subjected to thermal aging at 100 ºC for seven and 21 days. Mechanical tests were carried out on samples before and after aging, while exposed samples underwent visual inspection, optical microscopy, and Fourier transform infrared spectroscopy analysis. Visual inspection and microscopy revealed improved PP-HGM interaction due to the additives, with no deformation or damage from reprocessing. Infrared spectroscopy showed minor degradation in the PP structure post-exposure. In summary, the presence and content of HGM, reprocessing, and aging time significantly affect the mechanical properties (elastic modulus, breaking stress, elongation at break, and impact resistance).
- 31 December 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (7) , 6522-6535
Biodegradable composites filled with agro‐industrial waste and fertilizers for filament production and application in active manufacturing
One of the challenges to prioritizing a circular economy is the development of composites made with renewable polymer matrices and using agro‐industrial residues such as plant fibers. Aiming to follow the paths of a circular economy, this research aims to develop composites based on a blend of poly(butylene adipate‐co‐terephthalate) and polylactic acid filled with three plant residues: peanut shell, soybean shell, corn husk, and nitrogen–phosphorus–potassium fertilizer. For this, filaments of systems containing vegetable fiber (5 wt%) and fertilizer (3 wt%) were processed in a single‐screw extruder. The filaments were characterized by Fourier transfer infrared spectroscopy (FTIR), thermogravimetry, differential scanning calorimetry, surface morphological analysis, and mechanical behavior. The FTIR indicated changes in the blend's characteristic bands, suggesting an interaction between the polymer matrix and the fillers. The fertilizer altered the systems' thermal properties and thermal stability. The fertilizer significantly affected (p < 0.05) the mechanical properties in a particular way in each system. Finally, the presence of surface agglomerates were confirmed in the morphological analysis. Additionally, these composites can be applied as raw materials to produce filaments for active manufacturing in the agricultural sector, adding value to the available natural residues while adhering to a circular economy.Highlights: Poly(butylene adipate co‐terephthalate) (PBAT)/poly(lactic acid) (PLA) composites filaments were produced using agro‐industrial waste; Mineral compound fertilizer was incorporated into PBAT/PLA composites; Agro‐industrial waste in composites adds value to filler and promotes the circular economy.
- 31 December 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (7) , 6522-6535
Biodegradable composites filled with agro‐industrial waste and fertilizers for filament production and application in active manufacturing
One of the challenges to prioritizing a circular economy is the development of composites made with renewable polymer matrices and using agro‐industrial residues such as plant fibers. Aiming to follow the paths of a circular economy, this research aims to develop composites based on a blend of poly(butylene adipate‐co‐terephthalate) and polylactic acid filled with three plant residues: peanut shell, soybean shell, corn husk, and nitrogen–phosphorus–potassium fertilizer. For this, filaments of systems containing vegetable fiber (5 wt%) and fertilizer (3 wt%) were processed in a single‐screw extruder. The filaments were characterized by Fourier transfer infrared spectroscopy (FTIR), thermogravimetry, differential scanning calorimetry, surface morphological analysis, and mechanical behavior. The FTIR indicated changes in the blend's characteristic bands, suggesting an interaction between the polymer matrix and the fillers. The fertilizer altered the systems' thermal properties and thermal stability. The fertilizer significantly affected (p < 0.05) the mechanical properties in a particular way in each system. Finally, the presence of surface agglomerates were confirmed in the morphological analysis. Additionally, these composites can be applied as raw materials to produce filaments for active manufacturing in the agricultural sector, adding value to the available natural residues while adhering to a circular economy.Highlights: Poly(butylene adipate co‐terephthalate) (PBAT)/poly(lactic acid) (PLA) composites filaments were produced using agro‐industrial waste; Mineral compound fertilizer was incorporated into PBAT/PLA composites; Agro‐industrial waste in composites adds value to filler and promotes the circular economy.
- Open Access
Natural Aging of Reprocessed Polypropylene Composites Filled with Sustainable Corn Fibers
Natural fiber reinforcements have the potential to enhance mechanical properties, thereby improving performance and durability in various applications. In this study, we comprehensively evaluated the impact of environmental degradation over 120 days on reprocessed polypropylene (PP) reinforced with corn husk fiber (CHF) composites. The manufactured systems underwent rigorous analysis using various techniques, including Fourier transform infrared spectroscopy, thermogravimetric analysis, optical microscopy, scanning electron microscopy, and tensile testing. These analyses revealed that climatic conditions significantly influenced (p < 0.05) the mechanical properties of all systems. Photodegradation led to surface morphological changes and chemical structures. Regardless, adding CHF filler proved a key factor, as it allowed for less susceptibility to environmental degradation than the reprocessed matrix. These findings, therefore, provide robust evidence supporting the feasibility of using CHF composites for manufacturing agricultural containers.
Open AccessNatural Aging of Reprocessed Polypropylene Composites Filled with Sustainable Corn Fibers
Natural fiber reinforcements have the potential to enhance mechanical properties, thereby improving performance and durability in various applications. In this study, we comprehensively evaluated the impact of environmental degradation over 120 days on reprocessed polypropylene (PP) reinforced with corn husk fiber (CHF) composites. The manufactured systems underwent rigorous analysis using various techniques, including Fourier transform infrared spectroscopy, thermogravimetric analysis, optical microscopy, scanning electron microscopy, and tensile testing. These analyses revealed that climatic conditions significantly influenced (p < 0.05) the mechanical properties of all systems. Photodegradation led to surface morphological changes and chemical structures. Regardless, adding CHF filler proved a key factor, as it allowed for less susceptibility to environmental degradation than the reprocessed matrix. These findings, therefore, provide robust evidence supporting the feasibility of using CHF composites for manufacturing agricultural containers.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 34 (1) , e20240010
Bio-high density polyethylene films embedded with organoclay and zinc pyrithione
Bio-high density polyethylene (BHDPE) films with organoclay and antimicrobial additives (zinc pyrithione) were evaluated. The composites were prepared in a single-screw extruder using the melt intercalation technique, and the films were obtained by flat extrusion. The diffractograms indicated the formation of an intercalated nanocomposite (BHDPE/6 wt% of clay). Infrared spectra suggested that the polymer predominates over the antimicrobial agent bands. Thermal stability was slightly reduced by up to 3°C. The clay and antimicrobial agent reduced the melting point and crystallinity of BHDPE by up to 12 °C and 13.3%, respectively. In addition, the presence of clay and antimicrobial agent significantly (p < 0.05) affected all mechanical properties. Proliferation of Staphylococcus aureus demonstrated that both evaluated additives did not significantly (p > 0.05) inhibit microbial growth. The results emphasize a promising application of the films for packaging that does not require antimicrobial control, with films highlighted by 6 wt% of clay.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 34 (1) , e20240010
Open AccessBio-high density polyethylene films embedded with organoclay and zinc pyrithione
Bio-high density polyethylene (BHDPE) films with organoclay and antimicrobial additives (zinc pyrithione) were evaluated. The composites were prepared in a single-screw extruder using the melt intercalation technique, and the films were obtained by flat extrusion. The diffractograms indicated the formation of an intercalated nanocomposite (BHDPE/6 wt% of clay). Infrared spectra suggested that the polymer predominates over the antimicrobial agent bands. Thermal stability was slightly reduced by up to 3°C. The clay and antimicrobial agent reduced the melting point and crystallinity of BHDPE by up to 12 °C and 13.3%, respectively. In addition, the presence of clay and antimicrobial agent significantly (p < 0.05) affected all mechanical properties. Proliferation of Staphylococcus aureus demonstrated that both evaluated additives did not significantly (p > 0.05) inhibit microbial growth. The results emphasize a promising application of the films for packaging that does not require antimicrobial control, with films highlighted by 6 wt% of clay.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 34 (1) , e20230042
Development of mulch films from biodegradable polymer and agro-industrial waste
Plasticulture improves crop quality and yield through polymeric films, but their improper disposal harms the environment due to humidity and contamination. This study aimed to develop biodegradable mulch films using soybean and peanut hulls and poly (butylene-adipate-co-terephthalate) (PBAT). The residues were characterized by thermogravimetric analysis and mulch films were evaluated by water absorption, contact angle and mechanical properties. The thermal behavior of the residues indicated stability below 200ºC. The agro-waste improved hydrophobicity but increased the water absorption values of the films by up to 18.5x (PBAT/SH5 after 14 days). Micrographs obtained by scanning electron microscopy indicated an important distribution of residue particles and formation of agglomerates, leading to lower mechanical performance. The study found that agro-industrial residues in powder form can be added to the polymeric matrix to produce biodegradable mulch films through traditional processing techniques. This approach has the potential to contribute to a more sustainable production system.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 34 (1) , e20230042
Open AccessDevelopment of mulch films from biodegradable polymer and agro-industrial waste
Plasticulture improves crop quality and yield through polymeric films, but their improper disposal harms the environment due to humidity and contamination. This study aimed to develop biodegradable mulch films using soybean and peanut hulls and poly (butylene-adipate-co-terephthalate) (PBAT). The residues were characterized by thermogravimetric analysis and mulch films were evaluated by water absorption, contact angle and mechanical properties. The thermal behavior of the residues indicated stability below 200ºC. The agro-waste improved hydrophobicity but increased the water absorption values of the films by up to 18.5x (PBAT/SH5 after 14 days). Micrographs obtained by scanning electron microscopy indicated an important distribution of residue particles and formation of agglomerates, leading to lower mechanical performance. The study found that agro-industrial residues in powder form can be added to the polymeric matrix to produce biodegradable mulch films through traditional processing techniques. This approach has the potential to contribute to a more sustainable production system.
- 7 December 2023
- Published by Elsevier in Food Chemistry
- Vol. 439, 138146
Biodegradable PBAT/PLA blend films incorporated with turmeric and cinnamomum powder: A potential alternative for active food packaging
- 7 December 2023
- Published by Elsevier in Food Chemistry
- Vol. 439, 138146
Biodegradable PBAT/PLA blend films incorporated with turmeric and cinnamomum powder: A potential alternative for active food packaging
- Open Access
- 1 January 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (1)
Chitosan-clay nanocomposite as a drug delivery system of ibuprofen
Chitosan/montmorillonite nanocomposite films were prepared by the solvent evaporation method to immobilize the drug ibuprofen (IBU) and delay its release in a medium that simulates the environment of the gastrointestinal tract. The effects of montmorillonite, at different mass proportions (10, 20, and 50%), on the morphological and physical properties of the films were studied. The samples were characterized by X-ray diffraction (XRD), Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), degree of swelling, drug encapsulation, and drug release efficiency. According to the XRD it was evidenced that the incorporation of montmorillonite to chitosan led to the formation of nanocomposites of ordered morphology. The infrared spectra confirmed the good interaction between montmorillonite and chitosan by the formation of nanocomposites. This fact, which favored the imprisonment of the IBU, reduced the diffusion coefficient in the studied systems. The micrographs comproved the formation of dense and uniform films. The controlled release profile, especially for the nanocomposite with 10% clay mass, showed a slow drug release rate. The incorporation of montmorillonite at different proportions produced different morphologies, with good encapsulation efficiency and an adequate profile for the controlled release of the drug.
- 1 January 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (1)
Open AccessChitosan-clay nanocomposite as a drug delivery system of ibuprofen
Chitosan/montmorillonite nanocomposite films were prepared by the solvent evaporation method to immobilize the drug ibuprofen (IBU) and delay its release in a medium that simulates the environment of the gastrointestinal tract. The effects of montmorillonite, at different mass proportions (10, 20, and 50%), on the morphological and physical properties of the films were studied. The samples were characterized by X-ray diffraction (XRD), Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), degree of swelling, drug encapsulation, and drug release efficiency. According to the XRD it was evidenced that the incorporation of montmorillonite to chitosan led to the formation of nanocomposites of ordered morphology. The infrared spectra confirmed the good interaction between montmorillonite and chitosan by the formation of nanocomposites. This fact, which favored the imprisonment of the IBU, reduced the diffusion coefficient in the studied systems. The micrographs comproved the formation of dense and uniform films. The controlled release profile, especially for the nanocomposite with 10% clay mass, showed a slow drug release rate. The incorporation of montmorillonite at different proportions produced different morphologies, with good encapsulation efficiency and an adequate profile for the controlled release of the drug.
- 15 August 2021
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 32 (12) , 4787-4804
The investigation of the stress cracking behavior of PBT by acoustic emission
Despite being a major cause of failure of polymer products under service, environmental stress cracking (ESC) is still a phenomenon poorly investigated and, as consequence, not fully understood. This article aims to contribute to this field in a study of the stress cracking behavior of polybutylene terephthalate (PBT) exposed to ethanol (a common fluid, used in several daily situations), by means of two types of mechanical tests (tensile and stress relaxation). During mechanical testing the technique of acoustic emission (AE) was applied to identify certain mechanisms of internal failure. As a non‐destructive technique, AE is widely used with metals to monitor the integrity of components but it is very scarcely applied to polymers. The article, therefore, innovates by using AE as a tool to better understand the ESC behavior of an engineering polymer produced under different conditions. The PBT samples were prepared by injection molding, using different mold temperatures (20°C, 40°C, and 80°C), resulting in different crystallinities. The results showed that the tensile properties were highly dependent on the crosshead speed and that ethanol affected the mechanical performance of the materials, anticipating the necking, but its evaporation during the experiment reduced the actual temperature on the sample bar. This latter effect caused an unexpected behavior, with an increase in tensile strength and reduction of stress relaxation rate, the opposite trends that would be expected from a stress cracking agent. The crystallinity of PBT had some influence on the results, with the more crystalline samples being more resistant to ESC, as observed by both stress relaxation and AE analyses. The technique of AE showed to be a very useful tool to understand the mechanical behavior and to differentiate the various testing conditions, with the detection and quantification of hits and released energy, related to the several stages of deformation and failure, including the formation of shear bands, nucleation and growth of crazes and cracks, and so forth. The fracture surface analyses by scanning electron microscopy were very consistent with the AE experiments, in which rough topography were related to high acoustic activities.
- 15 August 2021
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 32 (12) , 4787-4804
The investigation of the stress cracking behavior of PBT by acoustic emission
Despite being a major cause of failure of polymer products under service, environmental stress cracking (ESC) is still a phenomenon poorly investigated and, as consequence, not fully understood. This article aims to contribute to this field in a study of the stress cracking behavior of polybutylene terephthalate (PBT) exposed to ethanol (a common fluid, used in several daily situations), by means of two types of mechanical tests (tensile and stress relaxation). During mechanical testing the technique of acoustic emission (AE) was applied to identify certain mechanisms of internal failure. As a non‐destructive technique, AE is widely used with metals to monitor the integrity of components but it is very scarcely applied to polymers. The article, therefore, innovates by using AE as a tool to better understand the ESC behavior of an engineering polymer produced under different conditions. The PBT samples were prepared by injection molding, using different mold temperatures (20°C, 40°C, and 80°C), resulting in different crystallinities. The results showed that the tensile properties were highly dependent on the crosshead speed and that ethanol affected the mechanical performance of the materials, anticipating the necking, but its evaporation during the experiment reduced the actual temperature on the sample bar. This latter effect caused an unexpected behavior, with an increase in tensile strength and reduction of stress relaxation rate, the opposite trends that would be expected from a stress cracking agent. The crystallinity of PBT had some influence on the results, with the more crystalline samples being more resistant to ESC, as observed by both stress relaxation and AE analyses. The technique of AE showed to be a very useful tool to understand the mechanical behavior and to differentiate the various testing conditions, with the detection and quantification of hits and released energy, related to the several stages of deformation and failure, including the formation of shear bands, nucleation and growth of crazes and cracks, and so forth. The fracture surface analyses by scanning electron microscopy were very consistent with the AE experiments, in which rough topography were related to high acoustic activities.