Hongcan Yao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hongcan Yao has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Ping Tan
Guangzhou University
7 shared publications Fulin Zhou
School of Civil Engineering, Guangzhou University, Guangzhou, P. R. China
4 shared publicationsYanhui Liu
Earthquake Engineering Research and Test Center, Guangzhou University, Guangzhou, P. R. China
2 shared publicationsHuimeng Zhou
1 shared publication- Huimeng Zhou
Engineering Seismic Research Centre, Guangzhou University, Guangzhou 510006, P. R. China
1 shared publication - Jiajun Tan
Guangzhou University
1 shared publication
Latest Publications
- 3 July 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
Experimental Investigation of an Asymmetric Inerter Nonlinear Energy Sink for Vibration Control
Existing structural control devices such as nonlinear energy sinks (NESs) and tuned mass damper (TMD) have demonstrated outstanding control efficacy. However, they are susceptible to changes in structural frequency or excitation and require a large sliding mass or space for implementation, which impedes their widespread practical application. In this study, an asymmetric inerter (ASYMI) NES is proposed to improve control efficiency and reduce the mass of dampers. Based on a 1:8-scale two-story aluminum alloy frame structure constructed in a laboratory, the ASYMI NES is optimized and experimentally investigated. The structural parameters are identified by conducting free-vibration testing on the uncontrolled structure. In the laboratory, an adjustable inerter is designed using a gear-rack mechanism. Two seismic records are applied to the experimental structure in shaking table experiments to analyze the control effect of the ASYMI NES device under ground motion. The experimental results for a structure equipped with the control device is compared to the simulated data to analyze the reasons for the discrepancies between experimental and simulation results. The results revealed that the RMS and peak errors between the simulation and experimental results were both within 10%. Overall, the ASYMI NES demonstrated impressive control capabilities, even if the stiffness does not reach the optimal design stiffness during our experiments, indicating its strong potential for engineering applications.
- 3 July 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
Experimental Investigation of an Asymmetric Inerter Nonlinear Energy Sink for Vibration Control
Existing structural control devices such as nonlinear energy sinks (NESs) and tuned mass damper (TMD) have demonstrated outstanding control efficacy. However, they are susceptible to changes in structural frequency or excitation and require a large sliding mass or space for implementation, which impedes their widespread practical application. In this study, an asymmetric inerter (ASYMI) NES is proposed to improve control efficiency and reduce the mass of dampers. Based on a 1:8-scale two-story aluminum alloy frame structure constructed in a laboratory, the ASYMI NES is optimized and experimentally investigated. The structural parameters are identified by conducting free-vibration testing on the uncontrolled structure. In the laboratory, an adjustable inerter is designed using a gear-rack mechanism. Two seismic records are applied to the experimental structure in shaking table experiments to analyze the control effect of the ASYMI NES device under ground motion. The experimental results for a structure equipped with the control device is compared to the simulated data to analyze the reasons for the discrepancies between experimental and simulation results. The results revealed that the RMS and peak errors between the simulation and experimental results were both within 10%. Overall, the ASYMI NES demonstrated impressive control capabilities, even if the stiffness does not reach the optimal design stiffness during our experiments, indicating its strong potential for engineering applications.
- 18 October 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
Neural Network Time Delay Compensation Method Combined with Sliding Mode for Real-Time Hybrid Testing
In real-time hybrid testing (RTHT), there is an inevitable time delay in the loading system because of the dynamic characteristics of the loading-specimen system. Time delay can reduce the accuracy or even lead to the instability of the test. Because of the nonlinearity in loading-specimen systems and the uncertainty of the input signals, time delay has significant time-variant characteristics and uncertainty. To guarantee the stability and accuracy of RTHT, a backpropagation neural network time delay compensation method combined with sliding mode (BPNN-SM) is proposed. The BPNN-SM method uses sliding mode as a feedback controller of the loading system to improve robustness and compensate for part of the time delay. BPNN is used as the inverse compensation to compensate for the residual time delay and further improve robustness. The desired command and displacement responses of the experimental substructure are used as the input and output for training the BPNN inverse model of the loading-specimen system with a sliding mode controller. The BPNN has 4 hidden layers and 50 inputs in the input layer, which is expanded by one input data column to get enough data. BPNN can model highly complex nonlinear dynamic characteristics with a fully connected structure and calculate quickly using the error backpropagation mechanism, which makes the compensation more robust. The time delay compensation tests and RTHT of a single-degree-of-freedom (SDOF) structure based on the mast of SEG Plaza were conducted. The test results show that BPNN-SM has an excellent compensation effect.
- 18 October 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
Neural Network Time Delay Compensation Method Combined with Sliding Mode for Real-Time Hybrid Testing
In real-time hybrid testing (RTHT), there is an inevitable time delay in the loading system because of the dynamic characteristics of the loading-specimen system. Time delay can reduce the accuracy or even lead to the instability of the test. Because of the nonlinearity in loading-specimen systems and the uncertainty of the input signals, time delay has significant time-variant characteristics and uncertainty. To guarantee the stability and accuracy of RTHT, a backpropagation neural network time delay compensation method combined with sliding mode (BPNN-SM) is proposed. The BPNN-SM method uses sliding mode as a feedback controller of the loading system to improve robustness and compensate for part of the time delay. BPNN is used as the inverse compensation to compensate for the residual time delay and further improve robustness. The desired command and displacement responses of the experimental substructure are used as the input and output for training the BPNN inverse model of the loading-specimen system with a sliding mode controller. The BPNN has 4 hidden layers and 50 inputs in the input layer, which is expanded by one input data column to get enough data. BPNN can model highly complex nonlinear dynamic characteristics with a fully connected structure and calculate quickly using the error backpropagation mechanism, which makes the compensation more robust. The time delay compensation tests and RTHT of a single-degree-of-freedom (SDOF) structure based on the mast of SEG Plaza were conducted. The test results show that BPNN-SM has an excellent compensation effect.
- 8 May 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 27 (03)
A Discrete Fractional Sliding Mode Control Algorithm for Vibration Mitigation of Building Structures Considering Nonlinearities and Uncertainties
A fractional-order component is introduced and incorporated into the traditional sliding mode control (SMC) algorithm of seismically excited civil structures, leveraging its flexibility and integrity. The determination of the sliding mode surface in this paper incorporates the inclusion of a fractional-order item and subsequently derives the control force. Structural uncertainties and nonlinearities were considered to evaluate the control performance of the discrete fractional sliding mode control algorithm (DFSMC). The 40-story linear structure with the active mass damper system and the three-story nonlinear structure with the Bouc–Wen model were used as analytical models. The DFSMC algorithm exhibited an advantage over the traditional SMC algorithm in terms of control performance for linear structures. Specifically, the non-dimensional base shear criterion was reduced by 5.52% compared to the conventional SMC algorithm under the El Centro ground record. The control effectiveness of the DFSMC algorithm was further analyzed in the presence of uncertainties in the structural coefficients. The control criteria experienced a maximum decrease of 31.23% for SMC, 3.74% for SMC, 23.10% for DFSMC, 1.19% for SMC, 3.51% for SMC, and 18.03% for SMC when [ ], and [ ]. For a three-story nonlinear structure, the normalized base shear of DFSMC decreased from 2.3648 to 1.9916. It can be observed that the incorporation of parameters in the DFSMC algorithm enhances the potential for improved control performance.
- 8 May 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 27 (03)
A Discrete Fractional Sliding Mode Control Algorithm for Vibration Mitigation of Building Structures Considering Nonlinearities and Uncertainties
A fractional-order component is introduced and incorporated into the traditional sliding mode control (SMC) algorithm of seismically excited civil structures, leveraging its flexibility and integrity. The determination of the sliding mode surface in this paper incorporates the inclusion of a fractional-order item and subsequently derives the control force. Structural uncertainties and nonlinearities were considered to evaluate the control performance of the discrete fractional sliding mode control algorithm (DFSMC). The 40-story linear structure with the active mass damper system and the three-story nonlinear structure with the Bouc–Wen model were used as analytical models. The DFSMC algorithm exhibited an advantage over the traditional SMC algorithm in terms of control performance for linear structures. Specifically, the non-dimensional base shear criterion was reduced by 5.52% compared to the conventional SMC algorithm under the El Centro ground record. The control effectiveness of the DFSMC algorithm was further analyzed in the presence of uncertainties in the structural coefficients. The control criteria experienced a maximum decrease of 31.23% for SMC, 3.74% for SMC, 23.10% for DFSMC, 1.19% for SMC, 3.51% for SMC, and 18.03% for SMC when [ ], and [ ]. For a three-story nonlinear structure, the normalized base shear of DFSMC decreased from 2.3648 to 1.9916. It can be observed that the incorporation of parameters in the DFSMC algorithm enhances the potential for improved control performance.
- 15 April 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 23 (19)
Improved Three-Variable Control for Electromagnetic Mass Damper System Considering Control–Structure Interaction
Current methods account for control–structure interaction (CSI) in structural control design, which may be unavailable in the preliminary design phase of actively controlled structures due to the unknown dynamic characteristic of an actuator. Therefore, it may result in significant difference in the design and evaluation of an active structural control system when ignoring or considering CSI at different phases. To eliminate the CSI effects of electromagnetic mass damper (EMD) system and thus decouple the tracking control of EMD from the control design of structure, in this paper, an improved three-variable control (ITVC) combining a signal convertor, a typical three-variable controller, and a voltage compensator is developed. The voltage compensator counteracts the influence of lower-order CSI including viscous damping force and Coulomb friction. The three-variable controller reduces the higher-order CSI effects, while the signal convertor converts all command and feedback signals to the relative coordinate system and eliminates the additional CSI effects. Performance tests and frequency response tests of the EMD system show that the CSI effects are basically eliminated by ITVC. In addition, shake table tests are performed on a one-story actively controlled structure to further verify ITVC. Experimental results suggest that ITVC can apply accurate control force on the structure and achieve ideal structural response control.
- 15 April 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 23 (19)
Improved Three-Variable Control for Electromagnetic Mass Damper System Considering Control–Structure Interaction
Current methods account for control–structure interaction (CSI) in structural control design, which may be unavailable in the preliminary design phase of actively controlled structures due to the unknown dynamic characteristic of an actuator. Therefore, it may result in significant difference in the design and evaluation of an active structural control system when ignoring or considering CSI at different phases. To eliminate the CSI effects of electromagnetic mass damper (EMD) system and thus decouple the tracking control of EMD from the control design of structure, in this paper, an improved three-variable control (ITVC) combining a signal convertor, a typical three-variable controller, and a voltage compensator is developed. The voltage compensator counteracts the influence of lower-order CSI including viscous damping force and Coulomb friction. The three-variable controller reduces the higher-order CSI effects, while the signal convertor converts all command and feedback signals to the relative coordinate system and eliminates the additional CSI effects. Performance tests and frequency response tests of the EMD system show that the CSI effects are basically eliminated by ITVC. In addition, shake table tests are performed on a one-story actively controlled structure to further verify ITVC. Experimental results suggest that ITVC can apply accurate control force on the structure and achieve ideal structural response control.
- 12 November 2022
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 52 (2) , 524-544
A simple strategy for active structural control against control–structure–excitation effects: Concept, framework, and experiments
Active control is among the most effective control techniques for mitigating structural vibrations. Control–structure interaction (CSI) plays a significant role in modeling a control system. Popular methods incorporate the actuator dynamics and structure into the control system to account for CSI. The transfer function of the actuator can be identified through frequency response tests without physical modeling. However, this method ignores the effects of the excitation. Another approach is to create a physics‐based model of the actuator and include it in the control design, but its implementation may be challenging and requires a thorough understanding of the complex control system. In this study, the concept of control–structure–excitation effects (CSEE) is presented to account for the effects of the control, structure, and excitation on the transfer function of the actuator. In contrast to the existing control methods that consider CSI in system modeling, an improved control framework is proposed to eliminate the influence of CSI/CSEE on the control performance and thus decouple the tracking control of the actuator from the control design of the structure. This is achieved by introducing the control floor acceleration into the actuator controller and transforming the tracking of the absolute control force into that of the relative acceleration. The control strategy is simple and easy to implement based on conventional actuator control algorithms, such as three‐variable control. Frequency response tests and shake table tests were performed on a two‐story small‐scale structure to evaluate the effectiveness of the control strategy. It was confirmed that the improved control framework shows good tracking performance with respect to the control force and thus allows for ideal structural response control.
- 12 November 2022
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 52 (2) , 524-544
A simple strategy for active structural control against control–structure–excitation effects: Concept, framework, and experiments
Active control is among the most effective control techniques for mitigating structural vibrations. Control–structure interaction (CSI) plays a significant role in modeling a control system. Popular methods incorporate the actuator dynamics and structure into the control system to account for CSI. The transfer function of the actuator can be identified through frequency response tests without physical modeling. However, this method ignores the effects of the excitation. Another approach is to create a physics‐based model of the actuator and include it in the control design, but its implementation may be challenging and requires a thorough understanding of the complex control system. In this study, the concept of control–structure–excitation effects (CSEE) is presented to account for the effects of the control, structure, and excitation on the transfer function of the actuator. In contrast to the existing control methods that consider CSI in system modeling, an improved control framework is proposed to eliminate the influence of CSI/CSEE on the control performance and thus decouple the tracking control of the actuator from the control design of the structure. This is achieved by introducing the control floor acceleration into the actuator controller and transforming the tracking of the absolute control force into that of the relative acceleration. The control strategy is simple and easy to implement based on conventional actuator control algorithms, such as three‐variable control. Frequency response tests and shake table tests were performed on a two‐story small‐scale structure to evaluate the effectiveness of the control strategy. It was confirmed that the improved control framework shows good tracking performance with respect to the control force and thus allows for ideal structural response control.
- 14 August 2021
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 50 (13) , 3670-3691
Acceleration‐based sliding mode hierarchical control algorithm for shake table tests
Existing control algorithms for seismic shake table tests (STTs) generally exhibit limitations such as poor acceleration tracking for displacement control, instability that results in table drift for direct acceleration, force, or velocity control, and the lack of a theoretical justification for hybrid control. Therefore, a reliable control algorithm has become key for effective shake table control. This paper presents acceleration‐based sliding mode control (SMC) as a solution to the drawbacks of the traditional force‐based SMC; in this manner, the influence of the force of the tested structure applied on the table as well as unmodeled complex nonlinear forces, such as friction, are counteracted. An acceleration‐based sliding mode hierarchical control (ASMHC) algorithm is proposed, where the acceleration‐based SMC is used as the high‐level controller to generate the corrected acceleration command, and the low‐level controller, that includes feed‐forward and feedback control, tracks the acceleration command in real time. The high‐level controller, having zero asymptotic stability, and the low‐level controller, designed based on the system transfer function, ensure tracking stability in time and frequency domains, respectively. The proposed ASMHC algorithm was first verified by a series of bare STTs, and was then applied to a real STT of a two‐story steel structure. The experimental results show that the proposed ASMHC algorithm can achieve good tracking of displacement, velocity, and acceleration in both time and frequency domains, which ensures accurate reproduction of seismic excitation in STTs.
- 14 August 2021
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 50 (13) , 3670-3691
Acceleration‐based sliding mode hierarchical control algorithm for shake table tests
Existing control algorithms for seismic shake table tests (STTs) generally exhibit limitations such as poor acceleration tracking for displacement control, instability that results in table drift for direct acceleration, force, or velocity control, and the lack of a theoretical justification for hybrid control. Therefore, a reliable control algorithm has become key for effective shake table control. This paper presents acceleration‐based sliding mode control (SMC) as a solution to the drawbacks of the traditional force‐based SMC; in this manner, the influence of the force of the tested structure applied on the table as well as unmodeled complex nonlinear forces, such as friction, are counteracted. An acceleration‐based sliding mode hierarchical control (ASMHC) algorithm is proposed, where the acceleration‐based SMC is used as the high‐level controller to generate the corrected acceleration command, and the low‐level controller, that includes feed‐forward and feedback control, tracks the acceleration command in real time. The high‐level controller, having zero asymptotic stability, and the low‐level controller, designed based on the system transfer function, ensure tracking stability in time and frequency domains, respectively. The proposed ASMHC algorithm was first verified by a series of bare STTs, and was then applied to a real STT of a two‐story steel structure. The experimental results show that the proposed ASMHC algorithm can achieve good tracking of displacement, velocity, and acceleration in both time and frequency domains, which ensures accurate reproduction of seismic excitation in STTs.