Mirhan Ozdemir
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mirhan Ozdemir has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Polat Sendur
Mechanical Engineering Department Ozyegin University 34794 Istanbul Turkey
3 shared publications - Ugur Simsek
Department of Mechanical Engineering, Ozyegin University, 34794 Istanbul, Türkiye
3 shared publications Alican Celik
2 shared publicationsCemal Efe Gayir
2 shared publications- Orhan Gülcan
General Electric Aviation
2 shared publications Ugur Simsek
2 shared publications
Latest Publications
- 16 October 2026
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 333
Topology-optimized graded gyroid scaffolds balance stiffness, permeability, and shear stress
- 16 October 2026
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 333
Topology-optimized graded gyroid scaffolds balance stiffness, permeability, and shear stress
- Open Access
- 21 August 2023
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 39 (1) , 101-112
Üretim parametrelerinin, lazer toz yatağı füzyon yöntemi ile üretilen kafes yapıların çarpılma, boyutsal değişim ve yüzey pürüzlülüğü üzerindeki etkisi
Yüksek ısı transfer kabiliyeti, enerji absorbe edebilme ve ses izolasyonu özelliklerinden dolayı kafes yapılar havacılık, otomotiv ve biyomedikal sanayii başta olmak üzere bir çok alanda kullanılmaktadır. Kafes yapıların bu kabiliyetleri üzerinde farklı proses ve geometrik parametreler etkili olmaktadır. Farklı endüstriyel uygulamalarda, ilgili kafes yapısının uygun proses ve geometrik parametreler ile birlikte kullanılmasının, uygulama sonucu elde edilen verimi arttıracağı bilinen bir gerçektir. Bu çalışma, Taguchi deney tasarımı kullanarak, kafes yapılarda, kafes yapı çeşidinin, inşa yönünün ve hacim oranının, üretimden sonra parçada meydana gelecek çarpılma, yüzey pürüzlülüğü ve duvar kalınlık değişimi üzerindeki etkisini deneysel olarak incelemeye odaklanmıştır. Üretim için lazer toz yatağı füzyon yöntemi ve CoCrMo malzeme kullanılmıştır. Her bir parametrenin çarpılma, yüzey pürüzlülüğü ve duvar kalınlık değişimi üzerindeki etkisi ve optimum parametre seti, değişkenlerin analizi (ANOVA) metodu ile bulunmuştur. Yüzey pürüzlülüğü için en optimum parametre seti elmas kafes yapısı, 0,2 hacim oranı ve 90o inşa yönü olarak belirlenmiştir. Duvar kalınlığındaki değişim için ise en optimum parametre seti gyroid kafes yapısı, 0,4 hacim oranı ve 45o inşa yönü olarak belirlenmiştir.
- 21 August 2023
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 39 (1) , 101-112
Open AccessÜretim parametrelerinin, lazer toz yatağı füzyon yöntemi ile üretilen kafes yapıların çarpılma, boyutsal değişim ve yüzey pürüzlülüğü üzerindeki etkisi
Yüksek ısı transfer kabiliyeti, enerji absorbe edebilme ve ses izolasyonu özelliklerinden dolayı kafes yapılar havacılık, otomotiv ve biyomedikal sanayii başta olmak üzere bir çok alanda kullanılmaktadır. Kafes yapıların bu kabiliyetleri üzerinde farklı proses ve geometrik parametreler etkili olmaktadır. Farklı endüstriyel uygulamalarda, ilgili kafes yapısının uygun proses ve geometrik parametreler ile birlikte kullanılmasının, uygulama sonucu elde edilen verimi arttıracağı bilinen bir gerçektir. Bu çalışma, Taguchi deney tasarımı kullanarak, kafes yapılarda, kafes yapı çeşidinin, inşa yönünün ve hacim oranının, üretimden sonra parçada meydana gelecek çarpılma, yüzey pürüzlülüğü ve duvar kalınlık değişimi üzerindeki etkisini deneysel olarak incelemeye odaklanmıştır. Üretim için lazer toz yatağı füzyon yöntemi ve CoCrMo malzeme kullanılmıştır. Her bir parametrenin çarpılma, yüzey pürüzlülüğü ve duvar kalınlık değişimi üzerindeki etkisi ve optimum parametre seti, değişkenlerin analizi (ANOVA) metodu ile bulunmuştur. Yüzey pürüzlülüğü için en optimum parametre seti elmas kafes yapısı, 0,2 hacim oranı ve 90o inşa yönü olarak belirlenmiştir. Duvar kalınlığındaki değişim için ise en optimum parametre seti gyroid kafes yapısı, 0,4 hacim oranı ve 45o inşa yönü olarak belirlenmiştir.
- Open Access
- 21 March 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (11)
Experimental and Numerical Modal Characterization for Additively Manufactured Triply Periodic Minimal Surface Lattice Structures: Comparison between Free‐Size and Homogenization‐Based Optimization Methods
Homogenization‐based topology optimization (HMTO) is one of the most extensively used grading methods to generate functionally graded lattice structures (FGLs). However, it requires a precharacterization of the lattices, which is time‐consuming. As a remedy, free‐size optimization‐based graded lattice generation (FOGLG) is explored as an alternative method to generate the FGLs. This article builds on the authors’ previous work in which the HMTO and FOGLG approaches are studied to improve the dynamic characteristic of a design by using a single lattice type, namely, double gyroid (DG) structure. To show applicability of the proposed methods, different lattice types including diamond (D), gyroid (G), and I‐WP are employed to create FGLs herein. The frequency response analysis is performed, and the results from HMTO and FOGLG are compared in terms of their accuracy and efficiency. The optimized designs are then reconstructed by relative density mapping (RDM) and enhanced relative density mapping (ERDM) methods. The fabricated test samples made of cobalt–chromium using the direct metal laser melting (DMLM) technique are then experimentally validated using a laser vibrometer. The results reveal that HMTO and FOGLG can be used on the lattice types with a variety of configurations and relative densities.
- 21 March 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (11)
Open AccessExperimental and Numerical Modal Characterization for Additively Manufactured Triply Periodic Minimal Surface Lattice Structures: Comparison between Free‐Size and Homogenization‐Based Optimization Methods
Homogenization‐based topology optimization (HMTO) is one of the most extensively used grading methods to generate functionally graded lattice structures (FGLs). However, it requires a precharacterization of the lattices, which is time‐consuming. As a remedy, free‐size optimization‐based graded lattice generation (FOGLG) is explored as an alternative method to generate the FGLs. This article builds on the authors’ previous work in which the HMTO and FOGLG approaches are studied to improve the dynamic characteristic of a design by using a single lattice type, namely, double gyroid (DG) structure. To show applicability of the proposed methods, different lattice types including diamond (D), gyroid (G), and I‐WP are employed to create FGLs herein. The frequency response analysis is performed, and the results from HMTO and FOGLG are compared in terms of their accuracy and efficiency. The optimized designs are then reconstructed by relative density mapping (RDM) and enhanced relative density mapping (ERDM) methods. The fabricated test samples made of cobalt–chromium using the direct metal laser melting (DMLM) technique are then experimentally validated using a laser vibrometer. The results reveal that HMTO and FOGLG can be used on the lattice types with a variety of configurations and relative densities.
- Open Access
Effect of Build Parameters on the Compressive Behavior of Additive Manufactured CoCrMo Lattice Parts Based on Experimental Design
Due to their high specific strength, toughness, and corrosion and wear resistance characteristics, CoCrMo alloys are widely used in different industries and applications: wind turbines and jet-engine components, orthopedic implants, dental crowns, etc. The aim of this paper is to investigate the effect of lattice parameters on the compressive behavior of laser powder bed fusion (LPBF) parts from CoCrMo material. Build orientation, volume fraction, and lattice type are chosen as input parameters or control factors, and compressive yield strength (σy), elastic modulus (E), and specific energy absorption are chosen as the output or performance parameters for optimization. The Taguchi experimental design method is used in the arrangement of lattice parameters during experimental studies. The level of importance of the lattice parameters on σy, E, and specific energy absorption is determined by using analysis of variance (ANOVA). At the same material volume fractions, Diamond specimens showed higher σy and specific energy absorption than Gyroid and Primitive specimens, except σy at 0.4 volume fraction, where a Gyroid specimen showed the best result. The experimental and statistical results revealed that volume fraction and build orientation were found to be the major and minor effective factors, respectively, for all performance parameters (σy, E, and specific energy absorption). The effect of volume fraction on σy, E, and specific energy absorption was found to be 85.11%, 91.83%, and 57.71%, respectively. Lattice type was found to be the second-ranking factor, affecting σy, E, and specific energy absorption with contributions of 11.04%, 6.98%, and 39.40%, respectively. Multi objective optimization based on grey relation analysis showed that a Diamond specimen with 0.4 volume fraction and 45° build orientation was the best parameter set for the investigated performance outputs.
Open AccessEffect of Build Parameters on the Compressive Behavior of Additive Manufactured CoCrMo Lattice Parts Based on Experimental Design
Due to their high specific strength, toughness, and corrosion and wear resistance characteristics, CoCrMo alloys are widely used in different industries and applications: wind turbines and jet-engine components, orthopedic implants, dental crowns, etc. The aim of this paper is to investigate the effect of lattice parameters on the compressive behavior of laser powder bed fusion (LPBF) parts from CoCrMo material. Build orientation, volume fraction, and lattice type are chosen as input parameters or control factors, and compressive yield strength (σy), elastic modulus (E), and specific energy absorption are chosen as the output or performance parameters for optimization. The Taguchi experimental design method is used in the arrangement of lattice parameters during experimental studies. The level of importance of the lattice parameters on σy, E, and specific energy absorption is determined by using analysis of variance (ANOVA). At the same material volume fractions, Diamond specimens showed higher σy and specific energy absorption than Gyroid and Primitive specimens, except σy at 0.4 volume fraction, where a Gyroid specimen showed the best result. The experimental and statistical results revealed that volume fraction and build orientation were found to be the major and minor effective factors, respectively, for all performance parameters (σy, E, and specific energy absorption). The effect of volume fraction on σy, E, and specific energy absorption was found to be 85.11%, 91.83%, and 57.71%, respectively. Lattice type was found to be the second-ranking factor, affecting σy, E, and specific energy absorption with contributions of 11.04%, 6.98%, and 39.40%, respectively. Multi objective optimization based on grey relation analysis showed that a Diamond specimen with 0.4 volume fraction and 45° build orientation was the best parameter set for the investigated performance outputs.
- Open Access
- 1 November 2021
- Published by Elsevier in Materials & Design
- Vol. 210
An efficient design methodology for graded surface-based lattice structures using free-size optimization and enhanced mapping method
- 1 November 2021
- Published by Elsevier in Materials & Design
- Vol. 210
Open AccessAn efficient design methodology for graded surface-based lattice structures using free-size optimization and enhanced mapping method