Mengxin Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mengxin Liu has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Danqing Song
State Key Laboratory of Subtropical Building and Urban Science, School of Civil Engineering and Transportation, South China University of Technology, Guangzhou, China
2 shared publications - Huijun Jin
School of Ecology, Northeast Forestry University, Harbin 150080, China
2 shared publications - Akiko Inujima
Department of Medical Oncology, Kanazawa Medical University, 1-1 Daigaku, Uchinada-Machi, Kahoku 920-0293, Japan
1 shared publication - Chengtao Jiang
Nanjing University
1 shared publication - Chengwen Wang
State Key Laboratory of Hydroscience and Engineering, Tsinghua University, Beijing 100084, China
1 shared publication - Chun Liu
School of Earth Sciences and Engineering, Nanjing University, Nanjing, China
1 shared publication
Latest Publications
- Open Access
Investigation on Thermal Conductivity of Soil Under Freeze–Thaw Action Based on Machine Learning Models
Thermal conductivity is a crucial factor for the soil, which is significantly affected by environmental conditions. Based on the variation in the thermal conductivity and the influencing factors of silty clay obtained by the freeze–thaw cycle test, this paper adopted four machine learning models optimized by particle swarm optimization (PSO), including the artificial neural network model (ANN), random forest model (RF), support vector machine model (SVM), and extreme gradient boosting model (XGBoost) to predict the thermal conductivity of the soil. Meanwhile, mean absolute error (MAE), root mean square error (RMSE), and correlation coefficient(R2) were used to evaluate the accuracy of the models. The accuracy of the machine learning model and empirical model were also compared. Then, the Monte Carlo simulation was used to analyze the stability of the models. The research results showed that the predicted performance of the machine learning models is significantly better than the empirical models. Among all the machine learning models, the R2 of the PSO-ANN model is above 0.95, while both RMSE and MAE values are below 0.02 (W·m⁻¹·K⁻¹). In addition, the stability order of the machine learning models is PSO-XGBoost, PSO-ANN, PSO-RF, and PSO-SVM. Therefore, comprehensively considering the accuracy and stability of the four machine learning models, the PSO-ANN model is recommended to predict soil’s thermal conductivity under freeze–thaw action.
Open AccessInvestigation on Thermal Conductivity of Soil Under Freeze–Thaw Action Based on Machine Learning Models
Thermal conductivity is a crucial factor for the soil, which is significantly affected by environmental conditions. Based on the variation in the thermal conductivity and the influencing factors of silty clay obtained by the freeze–thaw cycle test, this paper adopted four machine learning models optimized by particle swarm optimization (PSO), including the artificial neural network model (ANN), random forest model (RF), support vector machine model (SVM), and extreme gradient boosting model (XGBoost) to predict the thermal conductivity of the soil. Meanwhile, mean absolute error (MAE), root mean square error (RMSE), and correlation coefficient(R2) were used to evaluate the accuracy of the models. The accuracy of the machine learning model and empirical model were also compared. Then, the Monte Carlo simulation was used to analyze the stability of the models. The research results showed that the predicted performance of the machine learning models is significantly better than the empirical models. Among all the machine learning models, the R2 of the PSO-ANN model is above 0.95, while both RMSE and MAE values are below 0.02 (W·m⁻¹·K⁻¹). In addition, the stability order of the machine learning models is PSO-XGBoost, PSO-ANN, PSO-RF, and PSO-SVM. Therefore, comprehensively considering the accuracy and stability of the four machine learning models, the PSO-ANN model is recommended to predict soil’s thermal conductivity under freeze–thaw action.
- 5 April 2024
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 301
A new peridynamic interface model for fracture analysis of imperfect interface
- 5 April 2024
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 301
A new peridynamic interface model for fracture analysis of imperfect interface
- 31 October 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 219, 124844
Effect of functionalization on thermal conductivity of hexagonal boron nitride/epoxy composites
- 31 October 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 219, 124844
Effect of functionalization on thermal conductivity of hexagonal boron nitride/epoxy composites
- Open Access
Damage Model of Steel Fiber-Reinforced Coal Gangue Concrete under Freeze–Thaw Cycles Based on Weibull Distribution
In order to improve the utilization rate of coal gangue and expand the application range of coal gangue concrete (CGC), a certain proportion of steel fiber was added to the concrete, and the freeze–thaw cycles (FTCs) and flexural tests were used to explore the effects of different mass replacement rates of coal gangue (0%, 25%, 50%, 75%, and 100%) and different proportions of the volumetric blending of the steel fiber (0%, 0.8%, 1.0%, and 1.2%) on the frost resistance of steel fiber-reinforced CGC (SCGC). The governing laws of mass loss rate, relative dynamic elastic modulus and load–midspan deflection curve were obtained on the base of the analysis of testing results. The damage mechanisms of the SCGC under the FTCs were analyzed using the results of scanning electron microscopy (SEM). Based on the Lemaitre’s strain equivalence principle and Krajcinovic’s vector damage theory, a damage evolution model of the SCGC under the FTCs was established by introducing the damage variable of the SCGC satisfying Weibull distribution. The results show an increasing mass loss rate of the SCGC and a decreasing relative dynamic elastic modulus with an increasing mass replacement rate of coal gangue. The proper content of the steel fiber can reduce the mass loss rate of concrete by 10~40% and the relative loss rate of dynamic elastic modulus of concrete by 2~8%, thus significantly improving the ductility and toughness of the concrete. The established damage evolution model is well validated by the experimental results, which further help to improve the modelling accuracy. This study provides key experimental data and a theoretical basis for a wider range of proper utilization of coal gangue in cold regions.
Open AccessDamage Model of Steel Fiber-Reinforced Coal Gangue Concrete under Freeze–Thaw Cycles Based on Weibull Distribution
In order to improve the utilization rate of coal gangue and expand the application range of coal gangue concrete (CGC), a certain proportion of steel fiber was added to the concrete, and the freeze–thaw cycles (FTCs) and flexural tests were used to explore the effects of different mass replacement rates of coal gangue (0%, 25%, 50%, 75%, and 100%) and different proportions of the volumetric blending of the steel fiber (0%, 0.8%, 1.0%, and 1.2%) on the frost resistance of steel fiber-reinforced CGC (SCGC). The governing laws of mass loss rate, relative dynamic elastic modulus and load–midspan deflection curve were obtained on the base of the analysis of testing results. The damage mechanisms of the SCGC under the FTCs were analyzed using the results of scanning electron microscopy (SEM). Based on the Lemaitre’s strain equivalence principle and Krajcinovic’s vector damage theory, a damage evolution model of the SCGC under the FTCs was established by introducing the damage variable of the SCGC satisfying Weibull distribution. The results show an increasing mass loss rate of the SCGC and a decreasing relative dynamic elastic modulus with an increasing mass replacement rate of coal gangue. The proper content of the steel fiber can reduce the mass loss rate of concrete by 10~40% and the relative loss rate of dynamic elastic modulus of concrete by 2~8%, thus significantly improving the ductility and toughness of the concrete. The established damage evolution model is well validated by the experimental results, which further help to improve the modelling accuracy. This study provides key experimental data and a theoretical basis for a wider range of proper utilization of coal gangue in cold regions.
- Open Access
Measurement of Excess Pore-Water Pressure in Frozen Soil at Subfreezing Temperatures Close to 0°C
Response of pore-water pressure has crucial effect on the engineering geological performance of permafrost ground. However, there is a dearth of literature on the measurement of pore-water pressure in frozen soils due to challenges with regard to technical and operational method. To validate the generation of pore-water pressure and to reveal its variation property in frozen soils at subfreezing temperatures close to 0°C, a miniature pressure transducer was utilized to conduct a number of confined compression tests. Double-wall structure avoided damage to the transducer during frozen soil sampling. The transducer at sample bottom perceived a pressure fluctuation as varying air pressure imposed on sample surface, proving the connectivity among the pores in frozen soils with a hysteretic effect on pressure transmission. Pore-water pressure experienced a progressive increase followed by a slow dissipation under invariable load and temperature conditions when water drainage was permitted, while a monotonic increase in pressure was observed for an undrained sample. With decreasing temperature, a smaller peak and a more dilatory dissipation were displayed. When the sample was exposed to a stepwise warming process, a similar performance for the pressure was obtained with abrupt rise at the turning point of temperature.
Open AccessMeasurement of Excess Pore-Water Pressure in Frozen Soil at Subfreezing Temperatures Close to 0°C
Response of pore-water pressure has crucial effect on the engineering geological performance of permafrost ground. However, there is a dearth of literature on the measurement of pore-water pressure in frozen soils due to challenges with regard to technical and operational method. To validate the generation of pore-water pressure and to reveal its variation property in frozen soils at subfreezing temperatures close to 0°C, a miniature pressure transducer was utilized to conduct a number of confined compression tests. Double-wall structure avoided damage to the transducer during frozen soil sampling. The transducer at sample bottom perceived a pressure fluctuation as varying air pressure imposed on sample surface, proving the connectivity among the pores in frozen soils with a hysteretic effect on pressure transmission. Pore-water pressure experienced a progressive increase followed by a slow dissipation under invariable load and temperature conditions when water drainage was permitted, while a monotonic increase in pressure was observed for an undrained sample. With decreasing temperature, a smaller peak and a more dilatory dissipation were displayed. When the sample was exposed to a stepwise warming process, a similar performance for the pressure was obtained with abrupt rise at the turning point of temperature.
- Open Access
- 19 December 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (24) , 17028
Investigation on the Seismic Wave Propagation Characteristics Excited by Explosion Source in High-Steep Rock Slope Site Using Discrete Element Method
The influence of seismic waves induced by explosion sources on the dynamic response characteristics of rock slope sites is one of the most important problems affecting engineering construction. To investigate the wave propagation characteristics and attenuation law of seismic waves induced by explosive sources in rock sites from the perspective of time and frequency domains, the high-performance matrix discrete element method (MatDEM) is used to carry out numerical simulation tests on a granite rock medium site. The discrete element model of the high-steep rock slope is established by MatDEM, and the dynamic analysis of the rock medium site is conducted by loading blasting vibration load to generate seismic waves. The results show that the seismic waves in the rock site present characteristics of arc propagation attenuation. The maximum attenuation rate of the dynamic response is the fastest within 0.3 s and 25 m from the explosion source. The slope region can weaken the dynamic response of seismic waves generated by the explosion source. In particular, the high-frequency band (>20 Hz) has an obvious filtering effect. The dynamic response of the P-wave induced by the explosive source is greater than that of the S-wave in the bedrock and surface region. The dynamic amplification effect of the P-wave is greater than that of the S-wave in the slope region. The seismic waves in the slope region show an attenuation effect along the slope surface and have a typical elevation amplification effect inside the slope.
- 19 December 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (24) , 17028
Open AccessInvestigation on the Seismic Wave Propagation Characteristics Excited by Explosion Source in High-Steep Rock Slope Site Using Discrete Element Method
The influence of seismic waves induced by explosion sources on the dynamic response characteristics of rock slope sites is one of the most important problems affecting engineering construction. To investigate the wave propagation characteristics and attenuation law of seismic waves induced by explosive sources in rock sites from the perspective of time and frequency domains, the high-performance matrix discrete element method (MatDEM) is used to carry out numerical simulation tests on a granite rock medium site. The discrete element model of the high-steep rock slope is established by MatDEM, and the dynamic analysis of the rock medium site is conducted by loading blasting vibration load to generate seismic waves. The results show that the seismic waves in the rock site present characteristics of arc propagation attenuation. The maximum attenuation rate of the dynamic response is the fastest within 0.3 s and 25 m from the explosion source. The slope region can weaken the dynamic response of seismic waves generated by the explosion source. In particular, the high-frequency band (>20 Hz) has an obvious filtering effect. The dynamic response of the P-wave induced by the explosive source is greater than that of the S-wave in the bedrock and surface region. The dynamic amplification effect of the P-wave is greater than that of the S-wave in the slope region. The seismic waves in the slope region show an attenuation effect along the slope surface and have a typical elevation amplification effect inside the slope.
- Open Access
- 17 December 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (24) , 16947
Application of Long-Range Cross-Hole Acoustic Wave Detection Technology in Geotechnical Engineering Detection: Case Studies of Tunnel-Surrounding Rock, Foundation and Subgrade
The adverse geological conditions of soil cave, karst cave and goaf in deep foundation directly affect the safety and economy of geotechnical engineering construction. It is a difficult problem in geotechnical engineering detection to detect the distribution of bad geological conditions efficiently and accurately. Aiming at the problems of short penetrating distance and low resolution of cross-hole acoustic wave detection in rock-soil mass, based on the characteristics of acoustic wave propagation in rock and soil layers and comprehensively utilizing the spark source and data acquisition device, a long-distance cross-hole acoustic wave detection technology is proposed. According to the indoor concrete model test and field tests of geotechnical engineering, the applicability of the long-distance cross-hole acoustic wave detection technology in the detection of geotechnical structure and adverse geological phenomena under complex geological conditions is verified. The results show that acoustic wave CT imaging can accurately detect the cavities in the indoor concrete model test. In addition, the field tests of the grouting effect of tunnel-surrounding rock, high-rise building foundation and subgrade further verify the rapidity, accuracy and intuitiveness of the long-distance cross-hole acoustic wave detection technology. This work provides a reference for eliminating the potential safety problems caused by adverse geological conditions and similar geotechnical engineering investigation.
- 17 December 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (24) , 16947
Open AccessApplication of Long-Range Cross-Hole Acoustic Wave Detection Technology in Geotechnical Engineering Detection: Case Studies of Tunnel-Surrounding Rock, Foundation and Subgrade
The adverse geological conditions of soil cave, karst cave and goaf in deep foundation directly affect the safety and economy of geotechnical engineering construction. It is a difficult problem in geotechnical engineering detection to detect the distribution of bad geological conditions efficiently and accurately. Aiming at the problems of short penetrating distance and low resolution of cross-hole acoustic wave detection in rock-soil mass, based on the characteristics of acoustic wave propagation in rock and soil layers and comprehensively utilizing the spark source and data acquisition device, a long-distance cross-hole acoustic wave detection technology is proposed. According to the indoor concrete model test and field tests of geotechnical engineering, the applicability of the long-distance cross-hole acoustic wave detection technology in the detection of geotechnical structure and adverse geological phenomena under complex geological conditions is verified. The results show that acoustic wave CT imaging can accurately detect the cavities in the indoor concrete model test. In addition, the field tests of the grouting effect of tunnel-surrounding rock, high-rise building foundation and subgrade further verify the rapidity, accuracy and intuitiveness of the long-distance cross-hole acoustic wave detection technology. This work provides a reference for eliminating the potential safety problems caused by adverse geological conditions and similar geotechnical engineering investigation.
- Open Access
- 1 October 2021
- Published by Elsevier in Cement and Concrete Composites
- Vol. 123
Dependence of chloride ion diffusivity on evolution of pore-structures in freeze-thawed shotcrete: Multiscale characterization and modeling
- 1 October 2021
- Published by Elsevier in Cement and Concrete Composites
- Vol. 123
Open AccessDependence of chloride ion diffusivity on evolution of pore-structures in freeze-thawed shotcrete: Multiscale characterization and modeling
- 25 February 2020
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 62 (8) , 2747-2753
Influence of periodic structure and pixel area on the performance of antenna‐coupled Nb 5 N 6 array detector
- 25 February 2020
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 62 (8) , 2747-2753
Influence of periodic structure and pixel area on the performance of antenna‐coupled Nb 5 N 6 array detector