Emilia Noorsal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Emilia Noorsal has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Saharul Arof
Universiti Kuala Lumpur, Malaysian Spanish Institute
8 shared publications - Hamzah Arof
Department of Electrical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur, Malaysia
5 shared publications Hamzah Arof
Engineering Department, Universiti Malaya, Jalan Universiti, 50603, Kuala Lumpur, Malaysia
4 shared publicationsPhilip Mawby
University of Warwick School of Engineering, Coventry, CV47AL, United Kingdom
4 shared publicationsSaharul Arof
Universiti Kuala Lumpur, Malaysian Spanish Institute Kulim Hi-Tech Park, 09000 Kulim, Kedah. Malaysia
4 shared publications- Halina Hassan
Universiti Kuala Lumpur, Malaysian Spanish Institute Kulim Hi-Tech Park
3 shared publications
Latest Publications
- 1 October 2025
- Published by Springer Nature
- p. 81-88
Sliding Mode in Direct Current Control of Driving Mode of Direct Current Drive Electric Vehicles
- 1 October 2025
- Published by Springer Nature
- p. 81-88
Sliding Mode in Direct Current Control of Driving Mode of Direct Current Drive Electric Vehicles
- 1 October 2025
- Published by Springer Nature
- p. 71-80
Expert System and Direct Torque Control to Extend the Electric Braking at the End of Resistive Braking Mode
- 1 October 2025
- Published by Springer Nature
- p. 71-80
Expert System and Direct Torque Control to Extend the Electric Braking at the End of Resistive Braking Mode
- 1 October 2025
- Published by Springer Nature
- p. 121-131
Development of Genetics Algorithm Look-Up Table in the Field Weakening Mode of a Series Motor Four Quadrants Drive DC Chopper
- 1 October 2025
- Published by Springer Nature
- p. 121-131
Development of Genetics Algorithm Look-Up Table in the Field Weakening Mode of a Series Motor Four Quadrants Drive DC Chopper
- Open Access
- 11 August 2025
- Published by Academic Science Publications and Distributions in International Journal of Environmental Sciences
- p. 2973-2996
Programmable and Flexible Stimulator for Neuromuscular FES
This paper presents the design of a programmable and flexible stimulator that generates biphasic stimulation waveforms for neuromuscular Functional Electrical Stimulation (FES). The FES device facilitates muscle contraction in the paralyzed limbs of spinal cord injury (SCI) patients by delivering low electrical pulses through electrode pads. A major challenge in FES-induced muscle contraction is early muscle fatigue, which significantly limits activities such as FES-assisted standing and walking. The use of a fixed stimulation pattern, typically a rectangular waveform, repeatedly activates the same motor units, leading to overwork and rapid fatigue. To address this limitation, this work proposes a programmable and flexible stimulator using an Arduino Mega 2560 microcontroller and biphasic output current source circuits. The stimulator allows for adjustable stimulus parameters, including biphasic output current (0–100 mA), pulse width (2 µs–20 ms), and frequency (20 Hz–2 kHz). Additionally, the system supports multiple waveform shapes, including rectangular, ramp-up/down, triangular, trapezoidal, exponential up/down, and burst pulses. The biphasic output current circuit was chosen for its safety advantages, as it prevents residual charge accumulation on the electrodes, reducing the risk of skin burns. The proposed design was first simulated using Proteus 8 software before being implemented and tested on hardware. The simulation and hardware measurement results confirmed and validated the stimulator’s functionality, demonstrating its ability to meet the specified design requirements.
- 11 August 2025
- Published by Academic Science Publications and Distributions in International Journal of Environmental Sciences
- p. 2973-2996
Open AccessProgrammable and Flexible Stimulator for Neuromuscular FES
This paper presents the design of a programmable and flexible stimulator that generates biphasic stimulation waveforms for neuromuscular Functional Electrical Stimulation (FES). The FES device facilitates muscle contraction in the paralyzed limbs of spinal cord injury (SCI) patients by delivering low electrical pulses through electrode pads. A major challenge in FES-induced muscle contraction is early muscle fatigue, which significantly limits activities such as FES-assisted standing and walking. The use of a fixed stimulation pattern, typically a rectangular waveform, repeatedly activates the same motor units, leading to overwork and rapid fatigue. To address this limitation, this work proposes a programmable and flexible stimulator using an Arduino Mega 2560 microcontroller and biphasic output current source circuits. The stimulator allows for adjustable stimulus parameters, including biphasic output current (0–100 mA), pulse width (2 µs–20 ms), and frequency (20 Hz–2 kHz). Additionally, the system supports multiple waveform shapes, including rectangular, ramp-up/down, triangular, trapezoidal, exponential up/down, and burst pulses. The biphasic output current circuit was chosen for its safety advantages, as it prevents residual charge accumulation on the electrodes, reducing the risk of skin burns. The proposed design was first simulated using Proteus 8 software before being implemented and tested on hardware. The simulation and hardware measurement results confirmed and validated the stimulator’s functionality, demonstrating its ability to meet the specified design requirements.
- Open Access
- 11 August 2025
- Published by Academic Science Publications and Distributions in International Journal of Environmental Sciences
- p. 2890-2906
Improvised Fuzzy Logic Controller Using Feedforward, Feedback Offset, And Proportional Integral For Knee Extension Rehabilitation With Nonlinearities Influences
Rehabilitation through exercise using functional electrical stimulation (FES) is an effective approach to aiding recovery for individuals with spinal cord injuries (SCI). FES devices induce muscle contractions via electrode pads, generating force and torque. Precise control is essential to prevent overstimulation, which could lead to fatigue, pain, or injury. However, nonlinear effects such as fatigue, spasticity, and time delays pose challenges to feedback control systems, often resulting in performance degradation. Fuzzy logic controllers (FLCs) are known for their robustness in addressing these issues but face constraints in control bandwidth and time delay management, which can lead to oscillations. This study proposes an enhanced FLC by designing fuzzy input membership functions, rules, and outputs and incorporating tuning strategies to address these limitations. Additionally, the integration of feedback offset, and proportional-integral strategies is emphasized to improve control bandwidth and mitigate the effects of time delays. The proposed control algorithm is simulated and evaluated using MATLAB/Simulink in the context of knee extension rehabilitation, which is characterized by nonlinearities. The results demonstrated that the newly enhanced FLC architecture could effectively overcome bandwidth and time delay challenges, validating its suitability for knee extension rehabilitation in SCI patients.
- 11 August 2025
- Published by Academic Science Publications and Distributions in International Journal of Environmental Sciences
- p. 2890-2906
Open AccessImprovised Fuzzy Logic Controller Using Feedforward, Feedback Offset, And Proportional Integral For Knee Extension Rehabilitation With Nonlinearities Influences
Rehabilitation through exercise using functional electrical stimulation (FES) is an effective approach to aiding recovery for individuals with spinal cord injuries (SCI). FES devices induce muscle contractions via electrode pads, generating force and torque. Precise control is essential to prevent overstimulation, which could lead to fatigue, pain, or injury. However, nonlinear effects such as fatigue, spasticity, and time delays pose challenges to feedback control systems, often resulting in performance degradation. Fuzzy logic controllers (FLCs) are known for their robustness in addressing these issues but face constraints in control bandwidth and time delay management, which can lead to oscillations. This study proposes an enhanced FLC by designing fuzzy input membership functions, rules, and outputs and incorporating tuning strategies to address these limitations. Additionally, the integration of feedback offset, and proportional-integral strategies is emphasized to improve control bandwidth and mitigate the effects of time delays. The proposed control algorithm is simulated and evaluated using MATLAB/Simulink in the context of knee extension rehabilitation, which is characterized by nonlinearities. The results demonstrated that the newly enhanced FLC architecture could effectively overcome bandwidth and time delay challenges, validating its suitability for knee extension rehabilitation in SCI patients.
- Open Access
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 34 (3) , 1566-1581
Pole placement tuning of proportional integral derivative feedback controller for knee extension model
Functional electrical stimulation (FES) has shown potential in rehabilitative exercises for patients recovering from spinal cord injuries. In recent developments, conventional open-loop FES control techniques have evolved into closed-loop systems that employ feedback controllers for automation. However, closed-loop FES systems often face challenges due to muscle non-linear effects, such as fatigue, time delays, stiffness, and spasticity. Therefore, an accurate non-linear knee model is required during the design stage, and precise tuning of the feedback controller parameters is vital. A proportional– integral–derivative (PID) controller is commonly used as a feedback controller due to its simplicity and ease of implementation. However, most PID tuning methods are complex and time consuming. This paper investigates the viability of employing the pole placement technique for tuning a PID controller that regulates the non-linear knee extension model. The pole placement method aims to improve the control and adaptability of the PID controller in closed-loop FES systems, specifically by facilitating knee extension exercises. MATLAB Simulink was used to assess the effectiveness of this tuning approach. Results showed that the PID controller performed satisfactorily without non-linearities, but performance varied with the inclusion of specific non-linearities. The pole placement tuning method facilitated preliminary assessments of PID controller performance, preceding highly advanced optimization.
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 34 (3) , 1566-1581
Open AccessPole placement tuning of proportional integral derivative feedback controller for knee extension model
Functional electrical stimulation (FES) has shown potential in rehabilitative exercises for patients recovering from spinal cord injuries. In recent developments, conventional open-loop FES control techniques have evolved into closed-loop systems that employ feedback controllers for automation. However, closed-loop FES systems often face challenges due to muscle non-linear effects, such as fatigue, time delays, stiffness, and spasticity. Therefore, an accurate non-linear knee model is required during the design stage, and precise tuning of the feedback controller parameters is vital. A proportional– integral–derivative (PID) controller is commonly used as a feedback controller due to its simplicity and ease of implementation. However, most PID tuning methods are complex and time consuming. This paper investigates the viability of employing the pole placement technique for tuning a PID controller that regulates the non-linear knee extension model. The pole placement method aims to improve the control and adaptability of the PID controller in closed-loop FES systems, specifically by facilitating knee extension exercises. MATLAB Simulink was used to assess the effectiveness of this tuning approach. Results showed that the PID controller performed satisfactorily without non-linearities, but performance varied with the inclusion of specific non-linearities. The pole placement tuning method facilitated preliminary assessments of PID controller performance, preceding highly advanced optimization.
- Open Access
- 1 December 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1261 (1) , 012031
Low Harmonics Plug-in Home Charging Electric Vehicle Battery Charger Simulation Model of Zero Crossing
Harmonic currents are high in conventional rectifiers. The previous work proposed a new battery charger circuit to reduce harmonics effect and improve total harmonic distortion (THD). The design and development of a home charging electric vehicle battery charger circuit should anticipate potential issues. For this reason, the proposed battery charger, buck chopper, and zero cross circuits must be simulated before real hardware implementation. Simulation and simulation models are needed to describe system behaviour because experimentation might be dangerous, expensive, and time-consuming. This paper describes a simulation model of a zero-crossing circuit and its control algorithm, that provide control signals to a five-level single phase Multi Level Rectifier (MLR)) to draw the MLR for a clean sinusoidal line current with low harmonics. The proposed circuit and the algorithms perform as expected when tested using MATLAB/Simulink and PROTEUS software.
- 1 December 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1261 (1) , 012031
Open AccessLow Harmonics Plug-in Home Charging Electric Vehicle Battery Charger Simulation Model of Zero Crossing
Harmonic currents are high in conventional rectifiers. The previous work proposed a new battery charger circuit to reduce harmonics effect and improve total harmonic distortion (THD). The design and development of a home charging electric vehicle battery charger circuit should anticipate potential issues. For this reason, the proposed battery charger, buck chopper, and zero cross circuits must be simulated before real hardware implementation. Simulation and simulation models are needed to describe system behaviour because experimentation might be dangerous, expensive, and time-consuming. This paper describes a simulation model of a zero-crossing circuit and its control algorithm, that provide control signals to a five-level single phase Multi Level Rectifier (MLR)) to draw the MLR for a clean sinusoidal line current with low harmonics. The proposed circuit and the algorithms perform as expected when tested using MATLAB/Simulink and PROTEUS software.
- Open Access
- 1 December 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1261 (1) , 012032
Low Harmonics Plug-in Home Charging Electric Vehicle Battery Charger BMS State of Charge Balancing using Priority and Sequencing Technique
Poor battery state of health (SOH) or unit cell replacement of a damaged battery may cause an imbalance in the state of charge (SOC) or battery voltage terminal of electric vehicle (EV) batteries, which can negatively impact EV performance and EV batteries when charging. Battery Management System (BMS) monitor charges safely and efficiently. BMS can maximize battery life, can estimate SOC and State of health (SOH). EV Charger charge batteries individually in sequence (parallel) or, at once while in series connection. BMS cell balance controls battery charging in series or parallel using macro charging circuits. This study discusses series motor DC drive Electric Car (EC) Battery Management System (BMS) utilizing macro charging circuit and cell balancing control method. The MATLAB/Simulink software used to test the control algorithm shows that the proposed BMS cell balancing algorithm works effectively and meets our expectations.
- 1 December 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1261 (1) , 012032
Open AccessLow Harmonics Plug-in Home Charging Electric Vehicle Battery Charger BMS State of Charge Balancing using Priority and Sequencing Technique
Poor battery state of health (SOH) or unit cell replacement of a damaged battery may cause an imbalance in the state of charge (SOC) or battery voltage terminal of electric vehicle (EV) batteries, which can negatively impact EV performance and EV batteries when charging. Battery Management System (BMS) monitor charges safely and efficiently. BMS can maximize battery life, can estimate SOC and State of health (SOH). EV Charger charge batteries individually in sequence (parallel) or, at once while in series connection. BMS cell balance controls battery charging in series or parallel using macro charging circuits. This study discusses series motor DC drive Electric Car (EC) Battery Management System (BMS) utilizing macro charging circuit and cell balancing control method. The MATLAB/Simulink software used to test the control algorithm shows that the proposed BMS cell balancing algorithm works effectively and meets our expectations.