Fei Gao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fei Gao has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Zhen Wang
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
2 shared publications - Chenkang Liu
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
1 shared publication - Cong Zhou
State Key Laboratory of Disaster Prevention and Mitigation of Explosion and Impact, Army Engineering University of PLA, Nanjing, China
1 shared publication - Guokai Zhang
School of Safety Science and Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
1 shared publication - Honglei Sun
School of Civil Engineering and Transportation, Hebei University of Technology, Tianjin, China
1 shared publication - Hujun Li
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
1 shared publication
Latest Publications
- 6 January 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (2) , 72
Damage and Creep Response of Tunnel Lining Concrete at Elevated Temperatures
- 6 January 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (2) , 72
Damage and Creep Response of Tunnel Lining Concrete at Elevated Temperatures
- Open Access
- 20 October 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (20) , 11210
Propagation Characteristics of Shock Waves and Distribution Features of Loads in T-Shaped Tunnels with Protected Door
The study focuses on the T-shaped tunnel scenario with protective doors, performs explosion tests using aluminized explosives, and investigates the propagation patterns and loading characteristics of explosion shock waves in the straight tunnel, at the T-shaped junction, and within the semi-enclosed space in front of the protective door. It was observed that, in comparison to TNT explosives, the overpressure curve of aluminized explosives in the near-explosion zone exhibited a two- batch characteristic. The second batch presented the maximum overpressure peak. In contrast, in the far zone, the curve displayed a stable triangular waveform. In the main tunnel of the T-shaped opening with protective doors, it was found that the back blast surface located in front of the entrance to the main tunnel experienced the maximum momentum, which could be as high as 12 times greater than that of the reflection area on the blast-facing surface at the entrance of the main tunnel and the shock-wave pressure wave pattern can be divided into four batch. The regularities of each measurement point in multiple tests show consistency, highlighting the influence laws of the geometric structure on the wave pattern and load distribution. In addition, this paper integrates LS-DYNA numerical simulation with aerodynamics theory to reveal that shock waves generate expansion waves and oblique shock waves as they pass through the T-shaped opening. After two reflections off the main tunnel wall and the door, a stable propagation waveform is established. In addition, through dimensional analysis and in combination with the experimental results, the momentum at key positions was analyzed and predicted. This study offers a reference for the design of relevant engineering protection measures.
- 20 October 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (20) , 11210
Open AccessPropagation Characteristics of Shock Waves and Distribution Features of Loads in T-Shaped Tunnels with Protected Door
The study focuses on the T-shaped tunnel scenario with protective doors, performs explosion tests using aluminized explosives, and investigates the propagation patterns and loading characteristics of explosion shock waves in the straight tunnel, at the T-shaped junction, and within the semi-enclosed space in front of the protective door. It was observed that, in comparison to TNT explosives, the overpressure curve of aluminized explosives in the near-explosion zone exhibited a two- batch characteristic. The second batch presented the maximum overpressure peak. In contrast, in the far zone, the curve displayed a stable triangular waveform. In the main tunnel of the T-shaped opening with protective doors, it was found that the back blast surface located in front of the entrance to the main tunnel experienced the maximum momentum, which could be as high as 12 times greater than that of the reflection area on the blast-facing surface at the entrance of the main tunnel and the shock-wave pressure wave pattern can be divided into four batch. The regularities of each measurement point in multiple tests show consistency, highlighting the influence laws of the geometric structure on the wave pattern and load distribution. In addition, this paper integrates LS-DYNA numerical simulation with aerodynamics theory to reveal that shock waves generate expansion waves and oblique shock waves as they pass through the T-shaped opening. After two reflections off the main tunnel wall and the door, a stable propagation waveform is established. In addition, through dimensional analysis and in combination with the experimental results, the momentum at key positions was analyzed and predicted. This study offers a reference for the design of relevant engineering protection measures.
- Open Access
- 13 January 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (1) , 214
Experimental Study of the Dynamic Shear Modulus of Saturated Coral Sand under Complex Consolidation Conditions
The shear modulus is an essential parameter that reflects the mechanical properties of the soil. However, little is known about the shear modulus of coral sand, especially under complex consolidation conditions. In this paper, we present the results of a multi-stage strain-controlled undrained cyclic shear test on saturated coral sand. The influences of several consolidation state parameters: effective mean principal stress (), consolidation ratio (kc), consolidation direction angle (α0), and coefficient of intermediate principal stress (b) on the maximum shear modulus (G0), the reference shear strain (γr) and the reduction of shear modulus (G) have been investigated. For a specified shear strain level, G will increase with increasing and kc, but decrease with increasing α0 and b. However, the difference between G for various α0 and b can be reduced by the increase of shear strain amplitude (γa). G0 shows an increasing trend with the increase of and kc; on the contrary, with the increase of α0 and b, G0 shows a decreasing trend. To quantify the effect of consolidation state parameters on G0, a new index (μG0) with four parameters (λ1, λ2, λ3, λ4) which is related to , kc, α0, b is proposed to modify the prediction model of G0 in literature. Similarly, the values of γr under different consolidation conditions are also evaluated comprehensively by the four parameters, and the related index (μγr) is used to predict γr for various consolidation state parameters. A new finding is that there is an identical relationship between normalized shear modulus G/G0 and normalized shear strain γa/γr for various consolidation state parameters and the Davidenkov model can describe the G/G0–γa/γr curves. By using the prediction model proposed in this paper, an excellent prediction of G can be obtained and the deviation between measured and predicted G is all within ±10%.- 13 January 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (1) , 214
Open AccessExperimental Study of the Dynamic Shear Modulus of Saturated Coral Sand under Complex Consolidation Conditions
The shear modulus is an essential parameter that reflects the mechanical properties of the soil. However, little is known about the shear modulus of coral sand, especially under complex consolidation conditions. In this paper, we present the results of a multi-stage strain-controlled undrained cyclic shear test on saturated coral sand. The influences of several consolidation state parameters: effective mean principal stress (), consolidation ratio (kc), consolidation direction angle (α0), and coefficient of intermediate principal stress (b) on the maximum shear modulus (G0), the reference shear strain (γr) and the reduction of shear modulus (G) have been investigated. For a specified shear strain level, G will increase with increasing and kc, but decrease with increasing α0 and b. However, the difference between G for various α0 and b can be reduced by the increase of shear strain amplitude (γa). G0 shows an increasing trend with the increase of and kc; on the contrary, with the increase of α0 and b, G0 shows a decreasing trend. To quantify the effect of consolidation state parameters on G0, a new index (μG0) with four parameters (λ1, λ2, λ3, λ4) which is related to , kc, α0, b is proposed to modify the prediction model of G0 in literature. Similarly, the values of γr under different consolidation conditions are also evaluated comprehensively by the four parameters, and the related index (μγr) is used to predict γr for various consolidation state parameters. A new finding is that there is an identical relationship between normalized shear modulus G/G0 and normalized shear strain γa/γr for various consolidation state parameters and the Davidenkov model can describe the G/G0–γa/γr curves. By using the prediction model proposed in this paper, an excellent prediction of G can be obtained and the deviation between measured and predicted G is all within ±10%. - 16 August 2021
- Published by Springer Nature in Journal of Materials Science
- Vol. 56 (30) , 16851-16864
Anisotropic mechanical properties of extrusion-based 3D printed layered concrete
- 16 August 2021
- Published by Springer Nature in Journal of Materials Science
- Vol. 56 (30) , 16851-16864
Anisotropic mechanical properties of extrusion-based 3D printed layered concrete