Alla Hunina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alla Hunina has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ihor Kolb
Department of Geodesy and Geoinformatics, Lviv National Environmental University, 1 V. Velykoho Str., 80381 Dubliany, Ukraine
1 shared publication - Ihor Trevoho
Lviv Polytechnic National University
1 shared publication Lviv Polytechnic National University
1 shared publicationM. Protsyk
1 shared publication- Mykhailo Fys
Doctor of Technical Sciences Professor Department of Cartography and Geospatial Modelling Lviv Polytechnic National University ( Lviv Ukraine
1 shared publication Mykhaylo Fys
Department of Cartography and Geospatial Modeling, Lviv Polytechnic National University, Lviv, Ukraine
1 shared publication
Latest Publications
- 30 April 2024
- Published by Elsevier in Remote Sensing Applications: Society and Environment
- Vol. 35
Determining of correlation relationship between angular elements of external orientation
- 30 April 2024
- Published by Elsevier in Remote Sensing Applications: Society and Environment
- Vol. 35
Determining of correlation relationship between angular elements of external orientation
- 1 September 2021
- Published by Modern Achievements of Geodesic Science and Industry in Modern achievements of geodesic science and industry
- Vol. 42 (II)
Results of the software application for determination elements of external orientation of digital images of topographic aerial surveying from UAV
One of the problems with the use of UAVs for high-precision mapping is the inability to install on these devices an accurate stabilization system to determine the angular EEO images, so there is a need to develop methods for accurate location of EEO. To date, there are many developments in the definition of elements of EEO. However, there are a number of issues in their practical implementation. This applies primarily to attempts to improve the accuracy of obtaining the coordinates of the points of objects on the ground. Aim. Investigate the possibility of the proposed algorithm for determining the elements of EEO of digital images obtained by aerial surveying from an UAV. Methodology. Based on the condition of collinearity, two types of functions are determined for which the minimum is searched. This process of determining the elements of the EEO is performed using software. A diverse set of programs makes it possible to implement such a search, and a reasonable initial approximation of the EEA and provides a definition of their optimal parameters [Hlotov, 2020; Zavarzin, 2013; Berezina, 2018; Kim Hon Ir, 2017]. Results. The proposed approach was tested on the corresponding digital images obtained by aerial surveying from UAVs at checkpoints, which made it possible to justify the effectiveness of the proposed method. The specified RMSE had the following values: = 0.15 m, = 0.18 m, = 0.40 m. After specifying the steel error = 0.06 m, = 0.03 m, = 0.25 m. The analysis of the unknown results confirms the improvement of the accuracy of coordinate determination by specifying the values of RMS relative to those obtained in the software package Models and the proposed algorithm. Scientific novelty and practical significance. An algorithm has been developed that makes it possible to determine the value of EEO using software without the use of special software for digital image processing. First of all, it makes it possible to improve the accuracy of EEO determination for digital images obtained from UAVs and allows to significantly expand the range of tasks using UAVs.
- 1 September 2021
- Published by Modern Achievements of Geodesic Science and Industry in Modern achievements of geodesic science and industry
- Vol. 42 (II)
Results of the software application for determination elements of external orientation of digital images of topographic aerial surveying from UAV
One of the problems with the use of UAVs for high-precision mapping is the inability to install on these devices an accurate stabilization system to determine the angular EEO images, so there is a need to develop methods for accurate location of EEO. To date, there are many developments in the definition of elements of EEO. However, there are a number of issues in their practical implementation. This applies primarily to attempts to improve the accuracy of obtaining the coordinates of the points of objects on the ground. Aim. Investigate the possibility of the proposed algorithm for determining the elements of EEO of digital images obtained by aerial surveying from an UAV. Methodology. Based on the condition of collinearity, two types of functions are determined for which the minimum is searched. This process of determining the elements of the EEO is performed using software. A diverse set of programs makes it possible to implement such a search, and a reasonable initial approximation of the EEA and provides a definition of their optimal parameters [Hlotov, 2020; Zavarzin, 2013; Berezina, 2018; Kim Hon Ir, 2017]. Results. The proposed approach was tested on the corresponding digital images obtained by aerial surveying from UAVs at checkpoints, which made it possible to justify the effectiveness of the proposed method. The specified RMSE had the following values: = 0.15 m, = 0.18 m, = 0.40 m. After specifying the steel error = 0.06 m, = 0.03 m, = 0.25 m. The analysis of the unknown results confirms the improvement of the accuracy of coordinate determination by specifying the values of RMS relative to those obtained in the software package Models and the proposed algorithm. Scientific novelty and practical significance. An algorithm has been developed that makes it possible to determine the value of EEO using software without the use of special software for digital image processing. First of all, it makes it possible to improve the accuracy of EEO determination for digital images obtained from UAVs and allows to significantly expand the range of tasks using UAVs.
- Open Access
- 12 July 2021
- Published by Vilnius Gediminas Technical University in Geodesy and Cartography
- Vol. 47 (2) , 96-103
THE STUDY OF THE “CETUS” UNMANNED AERIAL VEHICLE FOR TOPOGRAPHIC AERIAL SURVEYING
The work aims to analyze and study the possibilities of using “Cetus” unmanned aerial vehicle (UAV) for performing topographic aerial surveys. The authors developed and tested aircraft-type UAV for topographic aerial photography. The studies were conducted on a specialized landfill, at which there is an appropriate number of situational points whose coordinates are determined with high accuracy. These points were used as both reference and control points. The obtained UAV aerial survey materials were subjected to a phototriangulation process to determine the orientation elements and to analyze, first and foremost, the angular orientation elements. The surveying was carried out on a mountainous territory, where the spatial coordinates of 37 situational points were determined by the method of ground-based GPS survey with an average accuracy of up to 0.05 m. These points were used as reference and control points. Aerial photography was performed in such a way that the scale of the images was as uniform as possible. The design solutions implemented in the Cetus UAV provide all the possibilities to perform aerial surveys of territories in strict compliance with the projected flight parameters. UAV equipment provides the necessary real-time correction of the position of the aerial camera. At the same time the optimum straightness of routes, stability of scales and mutual overlapping of pictures is reached. Regarding the accuracy of obtaining the spatial coordinates of the points of terrain objects, using “Cetus” UAV surveys, plans can even be made on a scale of even 1: 1000. As a result of the creation of the UAV “Cetus”, it became possible to perform the topographic aerial survey of the territories and to create large-scale orthophotos that fully meet the instructions. As a result of testing the “Cetus” UAV, it can be used in production processes when drawing up topographic plans for a large-scale series: 1: 1000 – 1: 5000, which will significantly save the cost of performing topographic work.
- 12 July 2021
- Published by Vilnius Gediminas Technical University in Geodesy and Cartography
- Vol. 47 (2) , 96-103
Open AccessTHE STUDY OF THE “CETUS” UNMANNED AERIAL VEHICLE FOR TOPOGRAPHIC AERIAL SURVEYING
The work aims to analyze and study the possibilities of using “Cetus” unmanned aerial vehicle (UAV) for performing topographic aerial surveys. The authors developed and tested aircraft-type UAV for topographic aerial photography. The studies were conducted on a specialized landfill, at which there is an appropriate number of situational points whose coordinates are determined with high accuracy. These points were used as both reference and control points. The obtained UAV aerial survey materials were subjected to a phototriangulation process to determine the orientation elements and to analyze, first and foremost, the angular orientation elements. The surveying was carried out on a mountainous territory, where the spatial coordinates of 37 situational points were determined by the method of ground-based GPS survey with an average accuracy of up to 0.05 m. These points were used as reference and control points. Aerial photography was performed in such a way that the scale of the images was as uniform as possible. The design solutions implemented in the Cetus UAV provide all the possibilities to perform aerial surveys of territories in strict compliance with the projected flight parameters. UAV equipment provides the necessary real-time correction of the position of the aerial camera. At the same time the optimum straightness of routes, stability of scales and mutual overlapping of pictures is reached. Regarding the accuracy of obtaining the spatial coordinates of the points of terrain objects, using “Cetus” UAV surveys, plans can even be made on a scale of even 1: 1000. As a result of the creation of the UAV “Cetus”, it became possible to perform the topographic aerial survey of the territories and to create large-scale orthophotos that fully meet the instructions. As a result of testing the “Cetus” UAV, it can be used in production processes when drawing up topographic plans for a large-scale series: 1: 1000 – 1: 5000, which will significantly save the cost of performing topographic work.