Ankur Srivastava
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ankur Srivastava has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- David Steen
Department of Electrical Engineering, Chalmers University of Technology, 412 96 Gothenburg, Sweden
4 shared publications Le Anh Tuan
Department of Electrical Engineering, Division of Electric Power Engineering, Chalmers University of Technology, Gothenburg, Sweden
4 shared publicationsOla Carlson
3 shared publicationsDavid Steen
2 shared publications- Junbo Zhao
Dartmouth College
2 shared publications - Le Anh Tuan
Department of Electrical Engineering, Chalmers University of Technology, 412 96 Gothenburg, Sweden
2 shared publications
Latest Publications
- Top Cited Papers
- 3 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Smart Grid
- Vol. 16 (3) , 2554-2573
Cyber-Physical Interdependence for Power System Operation and Control
This paper summarizes the technical endeavors undertaken by the Task Force (TF) on Cyber-Physical Interdependence for Power System Operation and Control. The TF was established to investigate the cyber-physical interdependence of critical power system elements and their influence on the operation and control of energy systems. State-of-the-art analysis techniques, including co-simulation and digital twin technologies, are employed to address various layers of interdependence between cyber and physical systems, facilitating the identification of potential threats and vulnerabilities. The paper examines prospective trajectories for resilient cyber-physical systems and outlines the educational and workforce training imperatives for addressing cybersecurity threats in contemporary power systems. Furthermore, concluding remarks and future recommendations are provided to mitigate the inherent vulnerabilities within the extensively interoperable grid infrastructure.
- 3 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Smart Grid
- Vol. 16 (3) , 2554-2573
Top Cited PapersCyber-Physical Interdependence for Power System Operation and Control
This paper summarizes the technical endeavors undertaken by the Task Force (TF) on Cyber-Physical Interdependence for Power System Operation and Control. The TF was established to investigate the cyber-physical interdependence of critical power system elements and their influence on the operation and control of energy systems. State-of-the-art analysis techniques, including co-simulation and digital twin technologies, are employed to address various layers of interdependence between cyber and physical systems, facilitating the identification of potential threats and vulnerabilities. The paper examines prospective trajectories for resilient cyber-physical systems and outlines the educational and workforce training imperatives for addressing cybersecurity threats in contemporary power systems. Furthermore, concluding remarks and future recommendations are provided to mitigate the inherent vulnerabilities within the extensively interoperable grid infrastructure.
- 31 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 40 (4) , 3057-3073
State Estimation for Integrated Energy Systems: Motivations, Advances, and Future Work
This paper summarizes the technical activities of a three-year-long IEEE Task Force (TF) on State Estimation (SE) for Integrated Energy Systems (IES). It presents the formal definition and characteristics of IES, along with the comprehensive discussion on Electric Power Systems (EPS) model, and static and dynamic models associated with heating and natural gas systems. The paper also identifies the barriers of SE for IES, such as estimation modeling, observability analysis, and measurement requirements, together with addressing multi-scale dynamics. An extensive comparative analysis between Integrated Energy Systems–State Estimation (IES-SE) and more established Electric Power System–State Estimation (EPS-SE) is presented. The paper also provides future research needs and directions related to IES-SE.
- 31 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 40 (4) , 3057-3073
State Estimation for Integrated Energy Systems: Motivations, Advances, and Future Work
This paper summarizes the technical activities of a three-year-long IEEE Task Force (TF) on State Estimation (SE) for Integrated Energy Systems (IES). It presents the formal definition and characteristics of IES, along with the comprehensive discussion on Electric Power Systems (EPS) model, and static and dynamic models associated with heating and natural gas systems. The paper also identifies the barriers of SE for IES, such as estimation modeling, observability analysis, and measurement requirements, together with addressing multi-scale dynamics. An extensive comparative analysis between Integrated Energy Systems–State Estimation (IES-SE) and more established Electric Power System–State Estimation (EPS-SE) is presented. The paper also provides future research needs and directions related to IES-SE.
- Open Access
- 24 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 78237-78250
Decentralized Dynamic State Estimation of Transmission Lines Using Local Measurements
This paper presents a novel decentralized dynamic state estimation (DSE) method for estimating the dynamic states of a transmission line in real-time. The proposed method utilizes the sampled measurements from the local end of a transmission line, and thereafter DSE is performed by employing an unscented Kalman filter. The advantage of the proposed method is that the remote end state variables of a transmission line can be estimated using only the local end variables and, hence, the need for communication infrastructure is eliminated. Furthermore, an exact nonlinear model of the transmission line is utilized for estimation and the DSE of one transmission line is independent of the other lines. These in turn result in reduced complexity, higher accuracy, and easier implementation of the decentralized estimator. The proposed method is applied to a case study with realistic transmission line parameters. The results from the case study affirm that the proposed method accurately estimates the state variables under different operating conditions. Furthermore, robust performance is achieved with different noise variances and types. The proposed DSE method is envisioned to have potential applications in transmission line monitoring, control, and protection.
- 24 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 78237-78250
Open AccessDecentralized Dynamic State Estimation of Transmission Lines Using Local Measurements
This paper presents a novel decentralized dynamic state estimation (DSE) method for estimating the dynamic states of a transmission line in real-time. The proposed method utilizes the sampled measurements from the local end of a transmission line, and thereafter DSE is performed by employing an unscented Kalman filter. The advantage of the proposed method is that the remote end state variables of a transmission line can be estimated using only the local end variables and, hence, the need for communication infrastructure is eliminated. Furthermore, an exact nonlinear model of the transmission line is utilized for estimation and the DSE of one transmission line is independent of the other lines. These in turn result in reduced complexity, higher accuracy, and easier implementation of the decentralized estimator. The proposed method is applied to a case study with realistic transmission line parameters. The results from the case study affirm that the proposed method accurately estimates the state variables under different operating conditions. Furthermore, robust performance is achieved with different noise variances and types. The proposed DSE method is envisioned to have potential applications in transmission line monitoring, control, and protection.
- Open Access
- 31 January 2023
- Published by Elsevier in International Journal of Electrical Power & Energy Systems
- Vol. 148
Dynamic state estimation based transmission line protection scheme: Performance evaluation with different fault types and conditions
- 31 January 2023
- Published by Elsevier in International Journal of Electrical Power & Energy Systems
- Vol. 148
Open AccessDynamic state estimation based transmission line protection scheme: Performance evaluation with different fault types and conditions
- Open Access
- 5 August 2022
- Published by Elsevier in Energy Policy
- Vol. 169
Pathways for the development of future intelligent distribution grids
- 5 August 2022
- Published by Elsevier in Energy Policy
- Vol. 169
Open AccessPathways for the development of future intelligent distribution grids
- 20 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Delivery
- Vol. 38 (1) , 162-176
Transmission Line Protection Using Dynamic State Estimation and Advanced Sensors: Experimental Validation
This paper presents the experimental validation of a protection scheme for a transmission line based on dynamic state estimation along with the practical application of advanced sensors in this protection scheme. The scheme performs dynamic state estimation with high-frequency measurements provided by the sensors, assesses the operating condition (i.e., health) of the transmission line in real-time, and thereby determines the tripping signal whenever a fault is detected. The validation was carried out in two steps, first with simulation studies for a three-phase fault and then with the experimental implementation using a physical scaled-down model of a power system consisting of transmission lines, transformers, and loads. The simulation and validation results have shown that the scheme performs adequately in both normal and fault conditions. In the fault case with the experimental setup, the scheme could correctly detect the fault and send the trip signal to the line’s circuit breakers with a total fault clearing time of approximately 65 milliseconds which is comparable to conventional protection methods. The average processing time for a measurement sample block is 12.5 milliseconds. The results demonstrate that this scheme and the sensors would work for transmission line protection which can avoid relay coordination and settings issues.
- 20 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Delivery
- Vol. 38 (1) , 162-176
Transmission Line Protection Using Dynamic State Estimation and Advanced Sensors: Experimental Validation
This paper presents the experimental validation of a protection scheme for a transmission line based on dynamic state estimation along with the practical application of advanced sensors in this protection scheme. The scheme performs dynamic state estimation with high-frequency measurements provided by the sensors, assesses the operating condition (i.e., health) of the transmission line in real-time, and thereby determines the tripping signal whenever a fault is detected. The validation was carried out in two steps, first with simulation studies for a three-phase fault and then with the experimental implementation using a physical scaled-down model of a power system consisting of transmission lines, transformers, and loads. The simulation and validation results have shown that the scheme performs adequately in both normal and fault conditions. In the fault case with the experimental setup, the scheme could correctly detect the fault and send the trip signal to the line’s circuit breakers with a total fault clearing time of approximately 65 milliseconds which is comparable to conventional protection methods. The average processing time for a measurement sample block is 12.5 milliseconds. The results demonstrate that this scheme and the sensors would work for transmission line protection which can avoid relay coordination and settings issues.
- 30 March 2022
- Published by Elsevier in Electric Power Systems Research
- Vol. 209
An Optimization-Based Topology Error Detection Method for Power System State Estimation
- 30 March 2022
- Published by Elsevier in Electric Power Systems Research
- Vol. 209
An Optimization-Based Topology Error Detection Method for Power System State Estimation
- Open Access
- 17 August 2021
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 15 (23) , 3345-3359
Development of a DSO support tool for congestion forecast
This paper presents a novel DSO support tool with visualisation capability for forecasting network congestion in distribution systems with a high level of renewables. To incorporate the uncertainties in the distribution systems, the probabilistic power flow framework has been utilised. An advanced photovoltaic production forecast based on sky images and a load forecast using an artificial neural network is used as the input to the tool. In addition, advanced load models and operating modes of photovoltaic inverters have been incorporated into the tool. The tool has been applied in case studies to perform congestion forecasts for two real distribution systems to validate its usability and scalability. The results from case studies demonstrated that the tool performs satisfactorily for both small and large networks and is able to visualise the cumulative probabilities of nodes voltage deviation and network components (branches and transformers) congestion for a variety of forecast horizons as desired by the DSO. The results have also shown that explicit inclusion of load‐voltage dependency models would improve the accuracy of the congestion forecast. For demonstrating the applicability of the tool, it has been integrated into an existing distribution management system via the IoT platform of a DMS vendor, Atos Worldgrid.
- 17 August 2021
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 15 (23) , 3345-3359
Open AccessDevelopment of a DSO support tool for congestion forecast
This paper presents a novel DSO support tool with visualisation capability for forecasting network congestion in distribution systems with a high level of renewables. To incorporate the uncertainties in the distribution systems, the probabilistic power flow framework has been utilised. An advanced photovoltaic production forecast based on sky images and a load forecast using an artificial neural network is used as the input to the tool. In addition, advanced load models and operating modes of photovoltaic inverters have been incorporated into the tool. The tool has been applied in case studies to perform congestion forecasts for two real distribution systems to validate its usability and scalability. The results from case studies demonstrated that the tool performs satisfactorily for both small and large networks and is able to visualise the cumulative probabilities of nodes voltage deviation and network components (branches and transformers) congestion for a variety of forecast horizons as desired by the DSO. The results have also shown that explicit inclusion of load‐voltage dependency models would improve the accuracy of the congestion forecast. For demonstrating the applicability of the tool, it has been integrated into an existing distribution management system via the IoT platform of a DMS vendor, Atos Worldgrid.
- Open Access
- 28 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
A Review on Challenges and Solutions in Microgrid Protection
Protection of microgrid has become challenging due to the hosting of various actors such as distributed generation, energy storage systems, information and communication technologies, etc. The main protection challenges in the microgrid are the bi-directional power flow, protection blinding, sympathetic tripping, change in short-circuit level due to different modes of operation, and limited fault current contribution by converter-interfaced sources. This paper presents a comprehensive review of the available microgrid protection schemes which are based on traditional protection principles and emerging techniques such as machine learning, data-mining, wavelet transform, etc. A categorical assessment of the reviewed protection schemes is also presented. The key findings of the paper suggest that the time-domain and communication-assisted protection schemes could be suitable solutions to address the identified protection challenges in the microgrid.
- 28 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Open AccessA Review on Challenges and Solutions in Microgrid Protection
Protection of microgrid has become challenging due to the hosting of various actors such as distributed generation, energy storage systems, information and communication technologies, etc. The main protection challenges in the microgrid are the bi-directional power flow, protection blinding, sympathetic tripping, change in short-circuit level due to different modes of operation, and limited fault current contribution by converter-interfaced sources. This paper presents a comprehensive review of the available microgrid protection schemes which are based on traditional protection principles and emerging techniques such as machine learning, data-mining, wavelet transform, etc. A categorical assessment of the reviewed protection schemes is also presented. The key findings of the paper suggest that the time-domain and communication-assisted protection schemes could be suitable solutions to address the identified protection challenges in the microgrid.
- Open Access
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Chalmers Campus as a Testbed for Intelligent Grids and Local Energy Systems
This paper presents an overview of a testbed for intelligent distribution grids, local energy systems, and energy flexible buildings, which is being developed at the campus of Chalmers University of Technology in Gothenburg, Sweden. It describes the test sites, the functionalities, and the planned demonstration activities within the scope of on-going research projects. The proposed demonstrations include a local energy market platform, energy management solutions for microgrids and smart buildings, as well as voltage control in distribution grids. The paper aims to show how the physical energy supply systems of the university are being adapted to integrate the communication and control set-ups that provide the technical requirements for smart grid interoperability. As an example, the on-site implementation of remote battery control is presented, where initial results show the feasibility and potential benefits of the external control. Finally, challenges and lessons learned during the development of the testbed are highlighted.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Open AccessChalmers Campus as a Testbed for Intelligent Grids and Local Energy Systems
This paper presents an overview of a testbed for intelligent distribution grids, local energy systems, and energy flexible buildings, which is being developed at the campus of Chalmers University of Technology in Gothenburg, Sweden. It describes the test sites, the functionalities, and the planned demonstration activities within the scope of on-going research projects. The proposed demonstrations include a local energy market platform, energy management solutions for microgrids and smart buildings, as well as voltage control in distribution grids. The paper aims to show how the physical energy supply systems of the university are being adapted to integrate the communication and control set-ups that provide the technical requirements for smart grid interoperability. As an example, the on-site implementation of remote battery control is presented, where initial results show the feasibility and potential benefits of the external control. Finally, challenges and lessons learned during the development of the testbed are highlighted.