GWGuan Ying Wang

Guan Ying Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Guan Ying Wang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Determining Effect of Environmental Corrosivity on Atmospheric Corrosion of Weathering Steel

    by Jane Wang, Nafiseh Ebrahimi, Olga Naboka, Danick Gallant, Alban Morel, Marc-Olivier Gagné

    Weathering steel (WS) has been used in bridges since the 1960s as a substitute for carbon steel. WS contains small amounts of alloying elements, such as Cu, Cr, and Ni that promotes the formation of a stable oxide layer called a “patina”. The patina acts as a corrosion barrier, removing the need for coatings and reducing maintenance costs. However, in Canada WS bridges often require painting due to corrosive field conditions. While nitrates and sulfates are common air pollutants, the use of de-icing salt in Canadian climates is the main source of chloridein urban and rural environments that contributes to corrosion. Therefore, the effect of atmospheric corrosion environments on WS needs to be further investigated to better inform bridge owners on factors that could affect the integrity of their structures. This study uses electrochemical methods combined with surface analysis methods such as X-ray diffraction (XRD) and scanning electron microscopy (SEM) to study the effects of the anions Cl-, NO3 -, and SO4 2- on the patina formation of 350AT WS. In this work, the lower threshold limits for chloride and sulfate-initiated corrosion were determined by wet electrochemistry. The results indicate that a concentration of 100 ppm is the lower limit for chloride and a concentration of 10 ppm is the limit for the more aggressive sulfate. Subsequently, WS was exposed to various anion combinations and concentrations in wet-dry cycles and the formed patina was examined for corrosion protection. The XRD and SEM results show that the patina’s composition depends on the exposure medium. In the presence of 10 ppm of SO4 2-, the formation of a dense oxide layer occurs consisting of goethite (α-FeOOH), while in the presence of Cl-, the formation of less protective oxides are observed such as lepidocrocite (γ-FeOOH) and akaganeite (β-FeOOH). Figure 1

  • Polymer Electrolytes for Printed 2-D Microcapacitors with Silver Electrodes

    by Alvin Virya, Guan Ying Wang, Zhi Yi Wang, Ta-Ya Chu, Neil Graddage, Keryn Lian

    The next generations of wearable electronics require high-performance, low-cost, thin, and flexible 2-D electronic components, e.g. capacitors and transistors. The commercial feasibility of these technologies relies on printable, high throughput, highly electronically-conductive, and inexpensive silver electrodes/current collectors to replace gold counterparts. However, silver-based devices are prone to failure due to corrosion forming resistive oxides or dendrites in aqueous environments (as shown in Figure 1a). Polymer electrolytes, possessing high ionic conductivity and enabled double layer capacitance at electrode interface, are highly tunable to minimize the dendritic growth and can be a promising technology for these 2-D devices. In this study, some high-performance aqueous polymer electrolytes that have previously been demonstrated for supercapacitors were compared and modified for better integration into printed interdigitated devices with silver electrodes. The polymer electrolytes were evaluated for their apparent ionic conductivities, capacitance, and corrosion properties using cyclic voltammetry and electrochemical impedance spectroscopy. Polymer electrolytes can effectively inhibit dendritic formation as shown via optical microscope in Fig. 1b. The optimized electrolytes possessed (i) high ionic conductivity (>1 mS cm-1) at ambient, (ii) good ability to maintain well-dissociated ions enabling double layer capacitance formation (Fig. 1c), with capacitance >100 μF cm-2 and (iii) good compatibility with silver electrodes. Overall, the optimized polymer electrolytes can be a low-cost, viable alternative in printed electronics requiring high dielectric materials, such as microcapacitors and low-powered field-effect transistors. Figure 1


  • Open Access

    Electrolyte-Gated Field Effect Transistors in Biological Sensing: A Survey of Electrolytes

    by Guan Ying Wang, Keryn Lian, Ta-Ya Chu

    Low operating voltages, rapid response, and high-throughput fabrication compatibility are key advantages for the development of electrolyte-gated field effect transistors (EGFETs) for biological sensing. Among the key components in EGFET biosensors, electrolyte materials are relatively less investigated, especially alternatives to water-based liquid electrolytes such as ionic liquids, ion gels, polyelectrolytes, and solid polymer electrolytes. These electrolytes enable portable devices and environmental stability superior to their water-based liquid alternatives. In this review, we offer an up-to-date evaluation of the state of EGFET research and gauge the strengths and limitations of high-performance electrolytes for use in EGFET biosensor applications as well as the potential for computer-aided design of such sensing platforms. The recent progress of EGFET biosensors for some popular analytes are reviewed and the performance of these alternative electrolytes in transistor biosensing is assessed. The challenges and opportunities for electrolytes in EGFETs are discussed for future research directions in this field.


  • An aromatic amine-containing polymer as an additive to ambipolar polymer semiconductor realizing unipolar n-type charge transport

    by Yinghui He, Jesse T.E. Quinn, Suhyun Lee, Guan Ying Wang, Xu Li, Jinliang Wang, Yuning Li