Fang Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fang Wang has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Wenzhan Huang
School of Materials Science and Engineering, Taiyuan University of Science and Technology, Taiyuan 030024, China
3 shared publications - Jianjun Guo
School of Material Science and Technology, Taiyuan University of Science and Technology, Taiyuan 030024, China
2 shared publications - Lin Zhu
School of Material Science and Technology, Taiyuan University of Science and Technology, Taiyuan 030024, China
2 shared publications - Lucai Wang
School of Material Science and Technology, Taiyuan University of Science and Technology, Taiyuan 030024, China
2 shared publications Ning Li
School of Materials Science and Engineering, Taiyuan University of Science and Technology, Taiyuan, People’s Republic of China
2 shared publications- Shijie Zhang
School of Material Science and Technology, Taiyuan University of Science and Technology, Taiyuan 030024, China
2 shared publications
Latest Publications
- 25 August 2025
- Published by Springer Nature in JOM
- p. 1-10
Effects of Nb-W Microalloying on Continuous Cooling Transformation Behavior and Microstructure Evolution in Low-Alloy Steel
- 25 August 2025
- Published by Springer Nature in JOM
- p. 1-10
Effects of Nb-W Microalloying on Continuous Cooling Transformation Behavior and Microstructure Evolution in Low-Alloy Steel
- 24 February 2025
- Published by Springer Nature in JOM
- Vol. 77 (5) , 3651-3660
Regulation of Trace ZrCuTiNiBe Amorphous Alloy on Al-Si-Mg Alloy Microstructure
- 24 February 2025
- Published by Springer Nature in JOM
- Vol. 77 (5) , 3651-3660
Regulation of Trace ZrCuTiNiBe Amorphous Alloy on Al-Si-Mg Alloy Microstructure
- Open Access
Predicting New Single/Multiphase-Structure High-Entropy Alloys Using a Pattern Recognition Network
Machine learning methods were employed to predict the phase structures of high-entropy alloys (HEAs). These alloys were classified into four categories: bcc (body-centered cubic), fcc (face-centered cubic), bcc+fcc (body-centered cubic and face-centered cubic) and others (containing intermetallic compounds and other structural alloys). The utilized algorithm was a Pattern Recognition Network (PRN) utilizing cross-entropy as the loss function, enabling the prediction of HEAs’ phase formation probability. The PRN algorithm demonstrated an accuracy exceeding 87% based on the test data. The PRN algorithm successfully predicted the transformation from fcc to fcc+bcc and subsequently to a bcc structure with the increase in Al content in AlxCoCu6Ni6Fe6 and AlxCoCrCuNiFe HEAs. In addition, AlxCoCu6Ni6Fe6 (x = 1, 3, 6, 9) HEAs were prepared using a vacuum arc furnace, and the microstructure of the as-cast alloy was tested by means of XRD, SEM, and EBSD, confirming the high consistency between the predicted and observed phase structures. This study showcases the efficacy of the PRN algorithm in predicting both single- and multiphase-structure high-entropy alloys, offering valuable insights into alloy design and development.
Open AccessPredicting New Single/Multiphase-Structure High-Entropy Alloys Using a Pattern Recognition Network
Machine learning methods were employed to predict the phase structures of high-entropy alloys (HEAs). These alloys were classified into four categories: bcc (body-centered cubic), fcc (face-centered cubic), bcc+fcc (body-centered cubic and face-centered cubic) and others (containing intermetallic compounds and other structural alloys). The utilized algorithm was a Pattern Recognition Network (PRN) utilizing cross-entropy as the loss function, enabling the prediction of HEAs’ phase formation probability. The PRN algorithm demonstrated an accuracy exceeding 87% based on the test data. The PRN algorithm successfully predicted the transformation from fcc to fcc+bcc and subsequently to a bcc structure with the increase in Al content in AlxCoCu6Ni6Fe6 and AlxCoCrCuNiFe HEAs. In addition, AlxCoCu6Ni6Fe6 (x = 1, 3, 6, 9) HEAs were prepared using a vacuum arc furnace, and the microstructure of the as-cast alloy was tested by means of XRD, SEM, and EBSD, confirming the high consistency between the predicted and observed phase structures. This study showcases the efficacy of the PRN algorithm in predicting both single- and multiphase-structure high-entropy alloys, offering valuable insights into alloy design and development.
- Open Access
Effect of High-Frequency Electric Pulse on the Solidification Microstructure and Properties of Hypoeutectic Al-Si Alloy
The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The impact on the mechanical properties of the alloy was analyzed using a micro-Vickers hardness tester and multifunctional friction tester. During solidification, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300 A/cm2 and frequencies of 0 Hz, 500 Hz, 1000 Hz, and 2000 Hz. The experimental results show that the Lorentz force also increases as the high-frequency pulse frequency increases. Intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to grow, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1000 Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size being reduced to 13.87 μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1000 Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.
Open AccessEffect of High-Frequency Electric Pulse on the Solidification Microstructure and Properties of Hypoeutectic Al-Si Alloy
The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The impact on the mechanical properties of the alloy was analyzed using a micro-Vickers hardness tester and multifunctional friction tester. During solidification, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300 A/cm2 and frequencies of 0 Hz, 500 Hz, 1000 Hz, and 2000 Hz. The experimental results show that the Lorentz force also increases as the high-frequency pulse frequency increases. Intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to grow, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1000 Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size being reduced to 13.87 μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1000 Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.
- Open Access
- 19 December 2023
- Published by MDPI AG in Preprints.org
Effect of High-Frequency Electric Pulse on the Solidification Microstructure and Properties of Hypoeutectic Al-Si Alloy
The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.
- 19 December 2023
- Published by MDPI AG in Preprints.org
Open AccessEffect of High-Frequency Electric Pulse on the Solidification Microstructure and Properties of Hypoeutectic Al-Si Alloy
The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.
- Open Access
Foaming Behavior of Microsized Aluminum Foam Using Hot Rolling Precursor
Aluminum foam that is lightweight with high specific strength, high energy absorption and other characteristics can be used in aerospace, transportation, machinery manufacturing and other fields. The PCM method is usually used to prepare closed-cell aluminum foams. The microsized aluminum foams made by this process can solve the non-uniform pore structures caused by liquid drainage during the foaming process of large aluminum foams. The surface morphology and internal pore structure of microsized aluminum foams are affected by the quality of the precursor used for foaming. In this paper, foamable precursors were obtained via either hot rolling or hot extrusion and subsequently foamed. By analyzing the micromorphology and foaming process of the precursor, the influence of the technological method on the macroscopic pore structure of the final aluminum foam was studied. The results show that the aluminum powder particles in the precursor prepared with the hot rolling method had metallurgical bonding, and the outer surface was dense, with almost no porosity and holes in the interior. The microsized aluminum foam obtained after foaming was smooth in appearance, and the internal pore structure was round and uniform. The reason is that during the foaming process of microsize aluminum foam, the foaming agent was evenly distributed in the precursor of the hot rolling process because of its compact structure. During the foaming process, the decomposed gas of the foaming agent will not escape, and the evenly distributed foaming agent tends to nucleate in situ. In the process of rapid foaming, the pressure in the bubble is enough to resist the liquid drainage phenomenon caused by gravity, and the growth direction of the gas core is isotropic, which promotes the foam structure to be more rounded and uniform.
Open AccessFoaming Behavior of Microsized Aluminum Foam Using Hot Rolling Precursor
Aluminum foam that is lightweight with high specific strength, high energy absorption and other characteristics can be used in aerospace, transportation, machinery manufacturing and other fields. The PCM method is usually used to prepare closed-cell aluminum foams. The microsized aluminum foams made by this process can solve the non-uniform pore structures caused by liquid drainage during the foaming process of large aluminum foams. The surface morphology and internal pore structure of microsized aluminum foams are affected by the quality of the precursor used for foaming. In this paper, foamable precursors were obtained via either hot rolling or hot extrusion and subsequently foamed. By analyzing the micromorphology and foaming process of the precursor, the influence of the technological method on the macroscopic pore structure of the final aluminum foam was studied. The results show that the aluminum powder particles in the precursor prepared with the hot rolling method had metallurgical bonding, and the outer surface was dense, with almost no porosity and holes in the interior. The microsized aluminum foam obtained after foaming was smooth in appearance, and the internal pore structure was round and uniform. The reason is that during the foaming process of microsize aluminum foam, the foaming agent was evenly distributed in the precursor of the hot rolling process because of its compact structure. During the foaming process, the decomposed gas of the foaming agent will not escape, and the evenly distributed foaming agent tends to nucleate in situ. In the process of rapid foaming, the pressure in the bubble is enough to resist the liquid drainage phenomenon caused by gravity, and the growth direction of the gas core is isotropic, which promotes the foam structure to be more rounded and uniform.
- Open Access
Preparation and Heat Dissipation Properties Comparison of Al and Cu Foam
The space holder method, a kind of powder metallurgy method which can avoid the process of melting metal to prepare metal foams, has particular significance in solving the difficulty of preparing metal foams with high melting points. In this paper, Na2S2O3·5H2O, a novel space holder, was used to prepare aluminium foam and copper foam, which were then used to test the heat dissipation performance of the metal foams. We first prepared two kinds of cell structures for (spherical cell and composite cells) aluminium and copper foam, then, we compared the performances of their heat dissipation, and it was found that both the spherical cell metal foam and composite cell metal foam promoted heat dissipation in the environment of natural convection, and the difference between them was not apparent. In the environment of forced convection, the composite porous metal showed a better heat dissipation performance.
Open AccessPreparation and Heat Dissipation Properties Comparison of Al and Cu Foam
The space holder method, a kind of powder metallurgy method which can avoid the process of melting metal to prepare metal foams, has particular significance in solving the difficulty of preparing metal foams with high melting points. In this paper, Na2S2O3·5H2O, a novel space holder, was used to prepare aluminium foam and copper foam, which were then used to test the heat dissipation performance of the metal foams. We first prepared two kinds of cell structures for (spherical cell and composite cells) aluminium and copper foam, then, we compared the performances of their heat dissipation, and it was found that both the spherical cell metal foam and composite cell metal foam promoted heat dissipation in the environment of natural convection, and the difference between them was not apparent. In the environment of forced convection, the composite porous metal showed a better heat dissipation performance.
- Open Access
Compressive Properties and Failure Mechanisms of Gradient Aluminum Foams Prepared by a Powder Metallurgy Method
A layered gradient aluminum foam was prepared by powder sintering with sodium thiosulfate (Na2S2O3) particles as the cell-forming agent. By cutting, polishing and observing under a microscope, it was found that the aluminum powder particles were not completely melted after sintering but were only combined by surface melting. Based on the quasi-static compression test and the macroscopic diagram of the sample during deformation, the mechanical properties of gradient aluminum foam were studied, and their deformation characteristics and mechanism were analyzed and discussed.
Open AccessCompressive Properties and Failure Mechanisms of Gradient Aluminum Foams Prepared by a Powder Metallurgy Method
A layered gradient aluminum foam was prepared by powder sintering with sodium thiosulfate (Na2S2O3) particles as the cell-forming agent. By cutting, polishing and observing under a microscope, it was found that the aluminum powder particles were not completely melted after sintering but were only combined by surface melting. Based on the quasi-static compression test and the macroscopic diagram of the sample during deformation, the mechanical properties of gradient aluminum foam were studied, and their deformation characteristics and mechanism were analyzed and discussed.