Ashish Bahuguna
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ashish Bahuguna has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Mohd Firoj
Department of Earthquake Engineering, IIT Roorkee, Roorkee, India
5 shared publications Mohd Firoj
3 shared publications- Nadarajah Ravichandran
Clemson Univ
3 shared publications - Arun K. Saraf
Indian Institute of Technology Roorkee
2 shared publications - Daya Shanker
Department of Earthquake Engineering, Indian Institute of Technology, Roorkee, India
2 shared publications - Hardeep Panchal
IIT Roorkee
2 shared publications
Latest Publications
- 1 May 2026
- Published by American Society of Civil Engineers (ASCE) in International Journal of Geomechanics
- Vol. 26 (5) , 04026080
Nonlinear Seismic Risk Assessment of Reinforced Concrete Pile Groups in Charleston, South Carolina, Considering Three-Dimensional Soil–Structure Interaction
Most of the current seismic design specifications are based on traditional fixed-based or simplified soil–structure interaction (SSI) approaches, which often fail to estimate the accurate r...
- 1 May 2026
- Published by American Society of Civil Engineers (ASCE) in International Journal of Geomechanics
- Vol. 26 (5) , 04026080
Nonlinear Seismic Risk Assessment of Reinforced Concrete Pile Groups in Charleston, South Carolina, Considering Three-Dimensional Soil–Structure Interaction
Most of the current seismic design specifications are based on traditional fixed-based or simplified soil–structure interaction (SSI) approaches, which often fail to estimate the accurate r...
- 3 November 2025
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 178 (12) , 1104-1114
Enhancement in the performance of concrete using a crystalline admixture
Concrete structures deteriorate due to water ingress and aggressive chemical penetration, leading to steel corrosion, spalling and reduced durability. To mitigate these issues, the use of a crystalline admixture (CA) in concrete was explored in this study. The CA was used at a rate of 0.8% by weight of cement in concrete specimens, which were compared with control concrete without CA. The experimental results reveal significant performance improvements: the CA concrete exhibited a compressive strength increase of 15% at 28 days, while water permeability decreased by 24%. Additionally, rapid chloride penetration test results showed a reduction of 52% in total charge passed through the CA concrete (756.7 C) as compared with the control concrete (1573.3 C), classifying the admixed concrete as ‘very low’ penetrability compared with the ‘low’ rating of the control. These findings confirm that the CA significantly enhanced the durability and resilience of concrete, making the addition of CA a viable solution for extending the lifespan of concrete structures.
- 3 November 2025
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 178 (12) , 1104-1114
Enhancement in the performance of concrete using a crystalline admixture
Concrete structures deteriorate due to water ingress and aggressive chemical penetration, leading to steel corrosion, spalling and reduced durability. To mitigate these issues, the use of a crystalline admixture (CA) in concrete was explored in this study. The CA was used at a rate of 0.8% by weight of cement in concrete specimens, which were compared with control concrete without CA. The experimental results reveal significant performance improvements: the CA concrete exhibited a compressive strength increase of 15% at 28 days, while water permeability decreased by 24%. Additionally, rapid chloride penetration test results showed a reduction of 52% in total charge passed through the CA concrete (756.7 C) as compared with the control concrete (1573.3 C), classifying the admixed concrete as ‘very low’ penetrability compared with the ‘low’ rating of the control. These findings confirm that the CA significantly enhanced the durability and resilience of concrete, making the addition of CA a viable solution for extending the lifespan of concrete structures.
- 13 August 2025
- Published by Springer Nature in Indian Geotechnical Journal
- Vol. 56 (8) , 1-26
Effect of Shear Wave Velocity Contrast on Computed Surface Responses and Site Amplification Factors: A Case Study of Charleston, SC Seismic Zone
- 13 August 2025
- Published by Springer Nature in Indian Geotechnical Journal
- Vol. 56 (8) , 1-26
Effect of Shear Wave Velocity Contrast on Computed Surface Responses and Site Amplification Factors: A Case Study of Charleston, SC Seismic Zone
- Open Access
- 24 March 2025
- Published by MDPI AG in Geosciences
- Vol. 15 (4) , 115
Comparison of Seismic Site Factor Models Based on Equivalent Linear and Nonlinear Analyses and Correction Factors for Updating Equivalent Linear Results for Charleston, South Carolina
In practice, site-specific one-dimensional (1D) seismic site response analyses are conducted to compute surface acceleration time histories considering shear wave velocity profile, modulus reduction, damping, and site-specific ground motions. The computed surface responses depend not only on the geologic and seismic characteristics but also on the type of 1D analysis (i.e., equivalent linear or nonlinear) and the software. Equivalent linear analysis (EQLA) is preferred by practicing engineers because the analysis procedure is well defined, but the accuracy of the results is questionable for certain geologic and input motion characteristics. On the other hand, nonlinear analysis (NNLA) is accurate for any geologic and input motion characteristics, but it is complicated because certain steps in the analysis procedure are complicated and not well defined. The objective of this study is to compare the responses computed from EQLA and NNLA procedures and make recommendations on when to use EQLA and NNLA, considering Charleston, South Carolina; geology; and seismicity. About 18,000 NNLAs (DMOD2000 and DEEPSOIL) and EQLAs (SHAKE2000) were performed, considering variations in shear wave velocity profiles, shear modulus reduction curves, damping curves, and ground motions. Based on the results from each software, three seismic site factor models were developed and compared with the published models. Results show that the EQLAs produced conservative estimates compared to the NNLAs. It is also observed that the site factor model based on EQLA diverges from the models based on NNLA even at the lowest amplitude shaking considered in the study (0.05 g), particularly for profiles with low shear wave velocity. This indicates that soils behave nonlinearly even at low amplitude shaking. Although a similar shear stress/shear strain model is used in DMOD2000 and DEEPSOIL, the site factor models show significant differences. Finally, an easy-to-use chart was developed to select suitable software and analysis types for accurately computing the surface responses based on the peak ground acceleration (PGA) of the input motion at the reference rock outcrop and average shear wave velocity in the top 30 m.
- 24 March 2025
- Published by MDPI AG in Geosciences
- Vol. 15 (4) , 115
Open AccessComparison of Seismic Site Factor Models Based on Equivalent Linear and Nonlinear Analyses and Correction Factors for Updating Equivalent Linear Results for Charleston, South Carolina
In practice, site-specific one-dimensional (1D) seismic site response analyses are conducted to compute surface acceleration time histories considering shear wave velocity profile, modulus reduction, damping, and site-specific ground motions. The computed surface responses depend not only on the geologic and seismic characteristics but also on the type of 1D analysis (i.e., equivalent linear or nonlinear) and the software. Equivalent linear analysis (EQLA) is preferred by practicing engineers because the analysis procedure is well defined, but the accuracy of the results is questionable for certain geologic and input motion characteristics. On the other hand, nonlinear analysis (NNLA) is accurate for any geologic and input motion characteristics, but it is complicated because certain steps in the analysis procedure are complicated and not well defined. The objective of this study is to compare the responses computed from EQLA and NNLA procedures and make recommendations on when to use EQLA and NNLA, considering Charleston, South Carolina; geology; and seismicity. About 18,000 NNLAs (DMOD2000 and DEEPSOIL) and EQLAs (SHAKE2000) were performed, considering variations in shear wave velocity profiles, shear modulus reduction curves, damping curves, and ground motions. Based on the results from each software, three seismic site factor models were developed and compared with the published models. Results show that the EQLAs produced conservative estimates compared to the NNLAs. It is also observed that the site factor model based on EQLA diverges from the models based on NNLA even at the lowest amplitude shaking considered in the study (0.05 g), particularly for profiles with low shear wave velocity. This indicates that soils behave nonlinearly even at low amplitude shaking. Although a similar shear stress/shear strain model is used in DMOD2000 and DEEPSOIL, the site factor models show significant differences. Finally, an easy-to-use chart was developed to select suitable software and analysis types for accurately computing the surface responses based on the peak ground acceleration (PGA) of the input motion at the reference rock outcrop and average shear wave velocity in the top 30 m.
- 26 December 2023
- Published by Wiley in Earthquake Engineering and Resilience
- Vol. 2 (4) , 493-514
Analytical plasticity‐based model for soil–structure interaction of lumped system on heterogeneous soil media
In the present study, an analytical approach is developed for the soil–structure interaction for the linear, eq. linear and elastic‐perfectly plastic layered soil strata. The amplification factor is calculated at the top of a lumped structure incorporating layered soil, foundation, and super‐structure deformation. The equation of motion of the system under the normalized earthquake excitation is solved using the direct integration method. MATLAB script is developed to carry out the parametric study, and nonlinear time history analysis is performed. The present methodology is compared with the finite element model (FEM), which shows good agreement. The computational time is much less than the FEM method. A parametric study is carried out in terms of soil heterogeneity, mass ratio, slenderness ratio, excitation frequency, and material model. The results indicate that due to the heterogeneity of the soil, the response of the structure is increased significantly; with the increase in the mass ratio, the amplification factor decreases with excitation frequency up to resonance, and the effect of mass ratio is negligible at the higher frequency range; with the increase in slenderness ratio, the amplification factor increases up to resonance, however, at higher frequency ranges there is no effect of slenderness ratio.
- 26 December 2023
- Published by Wiley in Earthquake Engineering and Resilience
- Vol. 2 (4) , 493-514
Analytical plasticity‐based model for soil–structure interaction of lumped system on heterogeneous soil media
In the present study, an analytical approach is developed for the soil–structure interaction for the linear, eq. linear and elastic‐perfectly plastic layered soil strata. The amplification factor is calculated at the top of a lumped structure incorporating layered soil, foundation, and super‐structure deformation. The equation of motion of the system under the normalized earthquake excitation is solved using the direct integration method. MATLAB script is developed to carry out the parametric study, and nonlinear time history analysis is performed. The present methodology is compared with the finite element model (FEM), which shows good agreement. The computational time is much less than the FEM method. A parametric study is carried out in terms of soil heterogeneity, mass ratio, slenderness ratio, excitation frequency, and material model. The results indicate that due to the heterogeneity of the soil, the response of the structure is increased significantly; with the increase in the mass ratio, the amplification factor decreases with excitation frequency up to resonance, and the effect of mass ratio is negligible at the higher frequency range; with the increase in slenderness ratio, the amplification factor increases up to resonance, however, at higher frequency ranges there is no effect of slenderness ratio.
- 1 July 2023
- Published by Springer Nature
- p. 53-63
Co-seismic Deformation of Iran, 2021 Earthquake Using DInSAR Technique
- 1 July 2023
- Published by Springer Nature
- p. 53-63
Co-seismic Deformation of Iran, 2021 Earthquake Using DInSAR Technique
- 11 April 2023
- Published by Springer Nature in Pure and Applied Geophysics
- Vol. 180 (6) , 2007-2022
Thermal Anomaly, Co-Seismic Deformation and Seismic Source Parameters Estimation of June 21 2022, Afghanistan Earthquake Employing InSAR Observations
- 11 April 2023
- Published by Springer Nature in Pure and Applied Geophysics
- Vol. 180 (6) , 2007-2022
Thermal Anomaly, Co-Seismic Deformation and Seismic Source Parameters Estimation of June 21 2022, Afghanistan Earthquake Employing InSAR Observations
- 12 August 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 59
Effect of nonlinear soil−structure interaction and lateral stiffness on seismic performance of mid−rise RC building
- 12 August 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 59
Effect of nonlinear soil−structure interaction and lateral stiffness on seismic performance of mid−rise RC building
- 10 August 2022
- Published by Elsevier in Structures
- Vol. 44, 343-356
Numerical simulation of seismic response of Slope–Foundation–Structure interaction for mid–rise RC buildings at various locations
- 10 August 2022
- Published by Elsevier in Structures
- Vol. 44, 343-356
Numerical simulation of seismic response of Slope–Foundation–Structure interaction for mid–rise RC buildings at various locations