Kai Miao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kai Miao has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Kai Miao
State Key Laboratory of Manufacturing Systems Engineering, School of Mechanical Engineering, Xi’an Jiaotong University, Xi’an, China
4 shared publications - Dichen Li
School of Mechanical Engineering, Xi'an Jiaotong University
2 shared publications - Dichen Li
State Key Laboratory for Manufacturing System Engineering, School of Mechanical Engineering, Xi'an Jiaotong University, China
2 shared publications - Dichen Li
Aero Science Key Lab of High Reynolds Aerodynamic Force at High Speed, AVIC Aerodynamics Research Institute
2 shared publications - Fusheng Cao
State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications - Haitian Zhang
State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications
Latest Publications
- Open Access
- 1 March 2026
- Published by KEAI Publishing in Energetic Materials Frontiers
- Vol. 7 (4) , 452-462
Facile sol-gel synthesis of Al@PTFE core-shell powders for enhanced curing depth in UV-curing-assisted direct ink writing of composite solid propellants
- 1 March 2026
- Published by KEAI Publishing in Energetic Materials Frontiers
- Vol. 7 (4) , 452-462
Open AccessFacile sol-gel synthesis of Al@PTFE core-shell powders for enhanced curing depth in UV-curing-assisted direct ink writing of composite solid propellants
- Open Access
- 12 February 2025
- Published by Springer Nature in China Foundry
- Vol. 22 (2) , 128-138
High-temperature strength of gel casting silica-based ceramic core
- 12 February 2025
- Published by Springer Nature in China Foundry
- Vol. 22 (2) , 128-138
Open AccessHigh-temperature strength of gel casting silica-based ceramic core
- Open Access
Elimination of the Stray Grain Defects of Single Crystal Blade by Variable Wall Thickness Based on Integral Ceramic Mold
The stray grain defect is often found at the platform in the process of directional solidification of single crystal blades because local undercooling easily occurs in this area. A variable wall thickness mold based on stereolithography and gelcasting technology was proposed to solve the local undercooling at the platform. The influence of variable wall thickness mold on the temperature field of the platform during directional solidification was studied via simulation. The numerical simulation results show that variable wall thickness can effectively prevent heat dissipation at the platform, thereby reducing the undercooling and avoiding the formation of stray grains. At the same time, the influence of molds assembly angle on the formation of stray grains was analyzed, and the appropriate molds assembly angle is suggested.
Open AccessElimination of the Stray Grain Defects of Single Crystal Blade by Variable Wall Thickness Based on Integral Ceramic Mold
The stray grain defect is often found at the platform in the process of directional solidification of single crystal blades because local undercooling easily occurs in this area. A variable wall thickness mold based on stereolithography and gelcasting technology was proposed to solve the local undercooling at the platform. The influence of variable wall thickness mold on the temperature field of the platform during directional solidification was studied via simulation. The numerical simulation results show that variable wall thickness can effectively prevent heat dissipation at the platform, thereby reducing the undercooling and avoiding the formation of stray grains. At the same time, the influence of molds assembly angle on the formation of stray grains was analyzed, and the appropriate molds assembly angle is suggested.
- Open Access
The Effect of Scanning Strategies on FeCrAl Nuclear Thin-Wall Cladding Manufacturing Accuracy by Laser Powder Bed Fusion
FeCrAl alloy has been proposed as an alternative material for accident-tolerant fuel (ATF) cladding for nuclear reactors. Thin-wall cladding can be rapidly fabricated by laser powder bed fusion (LPBF). In this paper, a finite element model is established to simulate the transient temperature fields of the cladding under two different laser scanning strategies (linear scanning and ring scanning). In linear scanning simulations, bidirectional scanning, compared with unidirectional scanning, had a smaller temperature gradient along the radial direction. In the ring scanning simulation, the maximum temperature gradually increased and then became stable with the increase of layers. Then, FeCrAl thin-wall cladding with a wall thickness of 0.14 mm was fabricated by LPBF. FeCrAl cladding using the ring scanning strategy had a smaller roughness value (Ra = 4.061 μm). Ring scanning had better accuracy than bidirectional scanning for FeCrAl thin-wall cladding with a wall thickness below 0.4 mm. Therefore, compared with the bidirectional scanning, the ring scanning is more suitable for the high-accuracy manufacturing of FeCrAl thin-wall cladding.
Open AccessThe Effect of Scanning Strategies on FeCrAl Nuclear Thin-Wall Cladding Manufacturing Accuracy by Laser Powder Bed Fusion
FeCrAl alloy has been proposed as an alternative material for accident-tolerant fuel (ATF) cladding for nuclear reactors. Thin-wall cladding can be rapidly fabricated by laser powder bed fusion (LPBF). In this paper, a finite element model is established to simulate the transient temperature fields of the cladding under two different laser scanning strategies (linear scanning and ring scanning). In linear scanning simulations, bidirectional scanning, compared with unidirectional scanning, had a smaller temperature gradient along the radial direction. In the ring scanning simulation, the maximum temperature gradually increased and then became stable with the increase of layers. Then, FeCrAl thin-wall cladding with a wall thickness of 0.14 mm was fabricated by LPBF. FeCrAl cladding using the ring scanning strategy had a smaller roughness value (Ra = 4.061 μm). Ring scanning had better accuracy than bidirectional scanning for FeCrAl thin-wall cladding with a wall thickness below 0.4 mm. Therefore, compared with the bidirectional scanning, the ring scanning is more suitable for the high-accuracy manufacturing of FeCrAl thin-wall cladding.
- Open Access
Effect of Nano-Si3N4 Reinforcement on the Microstructure and Mechanical Properties of Laser-Powder-Bed-Fusioned AlSi10Mg Composites
Laser powder bed fusion (LPBF) technology is of great significance to the rapid manufacturing of high-performance metal parts. To improve the mechanical behavior of an LPBFed AlSi10Mg alloy, the influence of nano-Si3N4 reinforcement on densification behavior, microstructure, and tensile property of AlSi10Mg was studied. The experimental results show that 97% relative density of the 3 vol.% nano-Si3N4/AlSi10Mg composite was achieved via optimization of the LPBF process. With the increase in the nano-Si3N4 content, the tensile strength and the yield strength of the composite steadily increase as per the Orowan strengthening mechanism while the elongation decreases. In addition, nano-Si3N4 reinforcement reduces the width of the coarse cell structure region and the thermal influence region of the AlSi10Mg matrix. After annealing, the tensile strength of the nano-Si3N4/AlSi10Mg composite decreases and the elongation increases significantly.
Open AccessEffect of Nano-Si3N4 Reinforcement on the Microstructure and Mechanical Properties of Laser-Powder-Bed-Fusioned AlSi10Mg Composites
Laser powder bed fusion (LPBF) technology is of great significance to the rapid manufacturing of high-performance metal parts. To improve the mechanical behavior of an LPBFed AlSi10Mg alloy, the influence of nano-Si3N4 reinforcement on densification behavior, microstructure, and tensile property of AlSi10Mg was studied. The experimental results show that 97% relative density of the 3 vol.% nano-Si3N4/AlSi10Mg composite was achieved via optimization of the LPBF process. With the increase in the nano-Si3N4 content, the tensile strength and the yield strength of the composite steadily increase as per the Orowan strengthening mechanism while the elongation decreases. In addition, nano-Si3N4 reinforcement reduces the width of the coarse cell structure region and the thermal influence region of the AlSi10Mg matrix. After annealing, the tensile strength of the nano-Si3N4/AlSi10Mg composite decreases and the elongation increases significantly.
- Open Access
Study on the Properties of Coated Cutters on Functionally Graded WC-Co/Ni-Zr Substrates with FCC Phase Enriched Surfaces
Currently, the research on mechanical behavior and cutting performance of functionally graded carbides is quite limited, which limits the rapid development of high-performance cemented carbide cutting tools. Based on WC-Co-Zr and WC-Ni-Zr, this study synthesized two kinds of cemented carbide cutters, i.e., the cemented carbide cutters with homogeneous microstructure and functionally graded carbide (FGC) cutters with FCC phase ZrN-enriched surfaces. Furthermore, TiAlN coating has been investigated on these carbide cutters. Mechanical behavior, friction, wear performance, and cutting behavior have been investigated for these coated carbides and their corresponding substrates. It was found that, as compared with coated cutters on WC-Co/Ni-Zr carbide substrates with homogeneous microstructures, the coated cutters on WC-Co/Ni-Zr FGC substrates with FCC phase-enriched surfaces show higher wear resistance and cutting life, and the wear mechanism during cutting is mainly adhesion wear.
Open AccessStudy on the Properties of Coated Cutters on Functionally Graded WC-Co/Ni-Zr Substrates with FCC Phase Enriched Surfaces
Currently, the research on mechanical behavior and cutting performance of functionally graded carbides is quite limited, which limits the rapid development of high-performance cemented carbide cutting tools. Based on WC-Co-Zr and WC-Ni-Zr, this study synthesized two kinds of cemented carbide cutters, i.e., the cemented carbide cutters with homogeneous microstructure and functionally graded carbide (FGC) cutters with FCC phase ZrN-enriched surfaces. Furthermore, TiAlN coating has been investigated on these carbide cutters. Mechanical behavior, friction, wear performance, and cutting behavior have been investigated for these coated carbides and their corresponding substrates. It was found that, as compared with coated cutters on WC-Co/Ni-Zr carbide substrates with homogeneous microstructures, the coated cutters on WC-Co/Ni-Zr FGC substrates with FCC phase-enriched surfaces show higher wear resistance and cutting life, and the wear mechanism during cutting is mainly adhesion wear.
- Open Access
- 1 September 2021
- Published by Springer Nature in China Foundry
- Vol. 18 (5) , 433-441
Effect of mould baffle technology on stray grain formation in single crystal blades by integral fabrication based on 3D printing
- 1 September 2021
- Published by Springer Nature in China Foundry
- Vol. 18 (5) , 433-441
Open AccessEffect of mould baffle technology on stray grain formation in single crystal blades by integral fabrication based on 3D printing
- 24 August 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (2)
Effects of Boehmite on the Calcination Shrinkage and Mechanical Properties of Gypsum‐Bonded Molds
Calcination shrinkage is an essential factor in the evaluation of a gypsum‐bonded mold. Typically, if traditional fillers are used in a gypsum‐bonded mold, it is difficult to maintain sufficient strength due to the high dosages of fillers. Herein, a new filler system of gypsum, boehmite, is proposed to more efficiently compensate for shrinkage, while minimizing the impact on the strength. The effects of the fillers on the calcination shrinkages and mechanical properties of the gypsum‐bonded molds are studied. The phase transition and thermal expansion behaviors of the gypsum‐bonded molds are tested by thermal gravimetric analysis/differential scanning calorimetry (TG/DSC) and a thermal dilatometer. The microstructures of the fillers and gypsum‐bonded molds are characterized by a scanning electron microscope (SEM). The results show that the dosage of boehmite for near‐zero shrinkage is reduced to about 35 wt%, with the bending strength of the gypsum‐bonded mold remaining above 2 MPa throughout the whole calcination process. The mechanism of calcination expansion is revealed and ultimately attributed to the splitting of boehmite particles. This research provides a novel gypsum‐bonded mold for required high dimensional and mechanical properties, elevating the ability to form complex structures.
- 24 August 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (2)
Effects of Boehmite on the Calcination Shrinkage and Mechanical Properties of Gypsum‐Bonded Molds
Calcination shrinkage is an essential factor in the evaluation of a gypsum‐bonded mold. Typically, if traditional fillers are used in a gypsum‐bonded mold, it is difficult to maintain sufficient strength due to the high dosages of fillers. Herein, a new filler system of gypsum, boehmite, is proposed to more efficiently compensate for shrinkage, while minimizing the impact on the strength. The effects of the fillers on the calcination shrinkages and mechanical properties of the gypsum‐bonded molds are studied. The phase transition and thermal expansion behaviors of the gypsum‐bonded molds are tested by thermal gravimetric analysis/differential scanning calorimetry (TG/DSC) and a thermal dilatometer. The microstructures of the fillers and gypsum‐bonded molds are characterized by a scanning electron microscope (SEM). The results show that the dosage of boehmite for near‐zero shrinkage is reduced to about 35 wt%, with the bending strength of the gypsum‐bonded mold remaining above 2 MPa throughout the whole calcination process. The mechanism of calcination expansion is revealed and ultimately attributed to the splitting of boehmite particles. This research provides a novel gypsum‐bonded mold for required high dimensional and mechanical properties, elevating the ability to form complex structures.
- 19 June 2019
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 102 (12) , 7564-7574
Researches on the pyrolyzing strength of gelcasting Al 2 O 3 ‐based ceramic molds for double‐wall blade
An approach using AM‐MBAM and Na‐alginate double‐gel was proposed to avoid the cracking of ceramic impingement holes cores (CIHCs) during pyrolysis processing. Finite element analysis (FEA) was used to calculate the thermal stress that caused CIHCs cracking. For ceramic slurry with a double‐gel containing various proportions of alginate, the addition of 15.0 wt.% alginate was the most beneficial for the rheological and mechanical properties of Al 2 O 3 ‐based ceramic obtained by aqueous gelcasting based on the double‐gel network had a dramatically pyrolyzing strength of 14.1 MPa, which was 72.0 % higher than that of the ceramics based on the single AM‐MBAM system. The double‐gel network was responsible for the improved strength. By comparing the thermal stress with pyrolyzing strength, it was predicted that the available diameter of CIHCs was greater than 0.7 mm. Finally, CIHCs with a minimum diameter of 0.7 mm were successfully fabricated, consistent with the FEA prediction.
- 19 June 2019
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 102 (12) , 7564-7574
Researches on the pyrolyzing strength of gelcasting Al 2 O 3 ‐based ceramic molds for double‐wall blade
An approach using AM‐MBAM and Na‐alginate double‐gel was proposed to avoid the cracking of ceramic impingement holes cores (CIHCs) during pyrolysis processing. Finite element analysis (FEA) was used to calculate the thermal stress that caused CIHCs cracking. For ceramic slurry with a double‐gel containing various proportions of alginate, the addition of 15.0 wt.% alginate was the most beneficial for the rheological and mechanical properties of Al 2 O 3 ‐based ceramic obtained by aqueous gelcasting based on the double‐gel network had a dramatically pyrolyzing strength of 14.1 MPa, which was 72.0 % higher than that of the ceramics based on the single AM‐MBAM system. The double‐gel network was responsible for the improved strength. By comparing the thermal stress with pyrolyzing strength, it was predicted that the available diameter of CIHCs was greater than 0.7 mm. Finally, CIHCs with a minimum diameter of 0.7 mm were successfully fabricated, consistent with the FEA prediction.