Jie Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jie Liu has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Jiajia Yang
School of Materials Science and Engineering, North China University of Water Resources and Electric Power, Zhengzhou 450045, China
2 shared publications - Liang Huang
School of Materials Science and Engineering, North China University of Water Resources and Electric Power, Zhengzhou 450045, China
2 shared publications - Pengju Xu
School of Materials Science and Engineering, North China University of Water Resources and Electric Power, Zhengzhou 450045, China
2 shared publications - Qing Xu
R & D Sector, Foshan Huican Mechanical Equipment Co., Ltd., Foshan 528225, China
2 shared publications - Yong Huang
School of Materials Science and Engineering, Nanjing University of Science and Technology, Nanjing, China
2 shared publications - Zenglei Ni
School of Materials Science and Engineering, North China University of Water Resources and Electric Power, Zhengzhou 450045, China
2 shared publications
Latest Publications
- Open Access
Microstructure Evolution-Induced Mechanical Response in Welded Joints of 7075-T6 Aluminium Alloy Thin Sheets Subjected to Different Friction Stir Paths
As a solid-state joining technology, friction stir welding (FSW) exhibits significant advantages for joining aluminium alloys, including low heat input and minimal formation of intermetallic compounds, thereby enhancing joint quality and mitigating deformation. This study investigates the single-sided and double-sided FSW processes of 3 mm thick 7075-T6 aluminium alloy sheets, focusing on characterising the microstructure and mechanical properties of the joints. Experimental results show that at a rotational speed of 1500 rpm and a welding speed of 80 mm/min, the double-sided co-directional FSW joint achieves a tensile strength of 388 MPa and an elongation of 7.09%, significantly outperforming those of the other two welding paths. In the weld nugget zone (WNZ), continuous dynamic recrystallization (CDRX) occurs, generating uniformly refined equiaxed grains (average size: 1.10 μm) and facilitating the transformation of low-angle grain boundaries (LAGBs) to high-angle grain boundaries (HAGBs). Meanwhile, the strong rotated cube texture is remarkably weakened and replaced by random recrystallized brass textures with the lowest kernel average misorientation (KAM) value in the WNZ. In contrast, the thermo-mechanically affected zone (TMAZ) accumulates a high density of LAGBs due to welding-induced plastic deformation. Microhardness testing reveals a typical “W”-shaped distribution: WNZ hardness is relatively high but slightly lower than that of the base metal (BM), and the minimum hardness of the advancing side (AS) of the heat-affected zone (HAZ) is higher than that of the retreating side (RS). This study confirms that double-sided co-directional FSW crucially regulates microstructural evolution and improves the mechanical properties of 7075-T6 aluminium alloy joints, providing a viable process optimisation strategy for high-quality welding of thin-gauge sheets.
Open AccessMicrostructure Evolution-Induced Mechanical Response in Welded Joints of 7075-T6 Aluminium Alloy Thin Sheets Subjected to Different Friction Stir Paths
As a solid-state joining technology, friction stir welding (FSW) exhibits significant advantages for joining aluminium alloys, including low heat input and minimal formation of intermetallic compounds, thereby enhancing joint quality and mitigating deformation. This study investigates the single-sided and double-sided FSW processes of 3 mm thick 7075-T6 aluminium alloy sheets, focusing on characterising the microstructure and mechanical properties of the joints. Experimental results show that at a rotational speed of 1500 rpm and a welding speed of 80 mm/min, the double-sided co-directional FSW joint achieves a tensile strength of 388 MPa and an elongation of 7.09%, significantly outperforming those of the other two welding paths. In the weld nugget zone (WNZ), continuous dynamic recrystallization (CDRX) occurs, generating uniformly refined equiaxed grains (average size: 1.10 μm) and facilitating the transformation of low-angle grain boundaries (LAGBs) to high-angle grain boundaries (HAGBs). Meanwhile, the strong rotated cube texture is remarkably weakened and replaced by random recrystallized brass textures with the lowest kernel average misorientation (KAM) value in the WNZ. In contrast, the thermo-mechanically affected zone (TMAZ) accumulates a high density of LAGBs due to welding-induced plastic deformation. Microhardness testing reveals a typical “W”-shaped distribution: WNZ hardness is relatively high but slightly lower than that of the base metal (BM), and the minimum hardness of the advancing side (AS) of the heat-affected zone (HAZ) is higher than that of the retreating side (RS). This study confirms that double-sided co-directional FSW crucially regulates microstructural evolution and improves the mechanical properties of 7075-T6 aluminium alloy joints, providing a viable process optimisation strategy for high-quality welding of thin-gauge sheets.
- Open Access
- 24 December 2025
- Published by MDPI AG in Preprints.org
Microstructure Evolution-Induced Mechanical Response in Welded Joints of 7075-T6 Aluminium Alloy Thin Sheets Subjected to Different Friction Stir Paths
As a solid-state joining technology, friction stir welding (FSW) exhibits significant advantages for aluminium alloys, including low heat input and minimal intermetallic compounds formation, thereby enhancing joint quality and mitigating deformation. This study investigates the single-sided and double-sided FSW processes of 3-mm-thick 7075-T6 aluminium alloy sheets, focusing on characterizing the microstructure and mechanical properties of the joints. Experimental results show that under 1500 rpm rotation speed and 80 mm/min welding speed, the double-sided co-directional FSW joint achieves a tensile strength of 388 MPa and an elongation of 7.09%, significantly outperforming the other two welding paths. In the weld nugget zone (WNZ), continuous dynamic recrystallization (CDRX) occurs, generating uniformly refined equiaxed grains (average size: 1.10 μm) and facilitating the transformation of low-angle grain boundaries (LAGBs) to high-angle grain boundaries (HAGBs). Meanwhile the strong Rotated Cube texture is remarkably weakened into random recrystallized Brass textures with the lowest kernel average misorientation (KAM) value in the WNZ. In contrast, the thermo-mechanically affected zone (TMAZ) accumulates high-density LAGBs due to welding-induced plastic deformation. Microhardness testing reveals a typical "W"-shaped distribution: WNZ hardness is relatively high but slightly lower than that of the base metal (BM), and the minimum hardness in the advancing side (AS) heat-affected zone (HAZ) is higher than that on the retreating side (RS). This study confirms that double-sided co-directional FSW crucially regulates microstructural evolution and improves mechanical properties of 7075-T6 joints, providing a viable process optimization strategy for high-quality welding of thin-gauge sheets.
- 24 December 2025
- Published by MDPI AG in Preprints.org
Open AccessMicrostructure Evolution-Induced Mechanical Response in Welded Joints of 7075-T6 Aluminium Alloy Thin Sheets Subjected to Different Friction Stir Paths
As a solid-state joining technology, friction stir welding (FSW) exhibits significant advantages for aluminium alloys, including low heat input and minimal intermetallic compounds formation, thereby enhancing joint quality and mitigating deformation. This study investigates the single-sided and double-sided FSW processes of 3-mm-thick 7075-T6 aluminium alloy sheets, focusing on characterizing the microstructure and mechanical properties of the joints. Experimental results show that under 1500 rpm rotation speed and 80 mm/min welding speed, the double-sided co-directional FSW joint achieves a tensile strength of 388 MPa and an elongation of 7.09%, significantly outperforming the other two welding paths. In the weld nugget zone (WNZ), continuous dynamic recrystallization (CDRX) occurs, generating uniformly refined equiaxed grains (average size: 1.10 μm) and facilitating the transformation of low-angle grain boundaries (LAGBs) to high-angle grain boundaries (HAGBs). Meanwhile the strong Rotated Cube texture is remarkably weakened into random recrystallized Brass textures with the lowest kernel average misorientation (KAM) value in the WNZ. In contrast, the thermo-mechanically affected zone (TMAZ) accumulates high-density LAGBs due to welding-induced plastic deformation. Microhardness testing reveals a typical "W"-shaped distribution: WNZ hardness is relatively high but slightly lower than that of the base metal (BM), and the minimum hardness in the advancing side (AS) heat-affected zone (HAZ) is higher than that on the retreating side (RS). This study confirms that double-sided co-directional FSW crucially regulates microstructural evolution and improves mechanical properties of 7075-T6 joints, providing a viable process optimization strategy for high-quality welding of thin-gauge sheets.
- 1 April 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (20) , 23236-23248
The Effect of Laser Post-Heat Treatment of Laser Powder Bed Fusion High Nitrogen Steel on the Microstructure and Mechanical Properties
- 1 April 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (20) , 23236-23248
The Effect of Laser Post-Heat Treatment of Laser Powder Bed Fusion High Nitrogen Steel on the Microstructure and Mechanical Properties
- Open Access
A Novel Approach of Microstructure Refinement of TiAl in Laser Beam Welding
Grain refinement through borides is known to be suppressed when TiAl is welded with a laser beam. As β grains do not primarily nucleate on boride at a high cooling rate, a mixture of nitrogen and argon is applied as a protecting gas for the formation of TiN during solidification. The phase transformation is changed correspondingly from Liquid → Liquid + β → β → α + β → α + γ+ β → α2 + γ + B2 to Liquid → TiN + Liquid → β+ TiN → α + γ + TiN → α2 + γ+ TiN. It is found that β grains prefer to nucleate heterogeneously on the suspending TiN in the melt with orientation relationship , leading to refined β grains. α2 colonies that were thus modified into fine non-dendritic grains. The effects of nitrogen as a shielding atmosphere on the microstructure evolution of TiAl are elaborately studied.Open AccessA Novel Approach of Microstructure Refinement of TiAl in Laser Beam Welding
Grain refinement through borides is known to be suppressed when TiAl is welded with a laser beam. As β grains do not primarily nucleate on boride at a high cooling rate, a mixture of nitrogen and argon is applied as a protecting gas for the formation of TiN during solidification. The phase transformation is changed correspondingly from Liquid → Liquid + β → β → α + β → α + γ+ β → α2 + γ + B2 to Liquid → TiN + Liquid → β+ TiN → α + γ + TiN → α2 + γ+ TiN. It is found that β grains prefer to nucleate heterogeneously on the suspending TiN in the melt with orientation relationship , leading to refined β grains. α2 colonies that were thus modified into fine non-dendritic grains. The effects of nitrogen as a shielding atmosphere on the microstructure evolution of TiAl are elaborately studied.