Carmine Sabia
Research Subjects
Carmine Sabia has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Maurizio C. Barbato
Institute for Mechanical Engineering and Materials Technology, University of Applied Sciences and Arts of Southern Switzerland (SUPSI)
3 shared publications - Antonio Buffo
Department of Applied Science and Technology, Politecnico di Torino, Corso Duca Degli Abruzzi 24, 10129 Torino, Italy
1 shared publication - Daniele Luca Marchisio
Department of Applied Science and Technology, Politecnico di Torino, Torino, Italy
1 shared publication - Giovanni Frigerio1 shared publication
- Giuseppe Storti
Chemistry, Materials and Chemical Engineering Department “Giulio Natta”, Politecnico di Milano, Piazza L. da Vinci 32, 20133 Milan, Italy
1 shared publication - Heyko Jürgen Schultz
Department of Chemical Engineering, Faculty of Chemistry, University of Applied Sciences Niederrhein, Adlerstraße 32, 47798 Krefeld, Germany
1 shared publication
Latest Publications
- Open Access
- 2 February 2026
- Published by Elsevier in Advanced Powder Technology
- Vol. 37 (2)
PIV validation of the CFD simulation of single-phase velocity field in spiral jet mills
- 2 February 2026
- Published by Elsevier in Advanced Powder Technology
- Vol. 37 (2)
Open AccessPIV validation of the CFD simulation of single-phase velocity field in spiral jet mills
- Open Access
- 24 November 2025
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 3
On the Accuracy and Computational Load of Fast 1D Models for Solar Receiver Parametric Studies
A big challenge consists in maximizing the thermal efficiency of volumetric solar receivers that are used to collect solar energy and heat-up a heat transfer fluid in renewable energy systems. Parametric studies provide an undisputed aid in early design stages and fast computational models are important to rapidly test novel configurations. In this paper, a comprehensive analysis to assess the accuracy and the computational load of 1D and 3D models compared to relevant literature data is presented. A 1D finite volume model and a 1D explicit model based upon the thermal resistance network are built by solving the solid and fluid energy balances and results are compared to accurate 3D CFD simulations of a solar receiver consisting of a silicon-carbide absorbing structure. The calculated air and solid temperatures are compared to literature findings on a receiver test geometry for different heat transfer fluid velocities. Results show that fast 1D models provide very accurate results with a maximum error of 2%-5% with respect to the reference in a computational time of few seconds, two order of magnitude lower than the one needed by accurate 3D CFD simulations.
- 24 November 2025
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 3
Open AccessOn the Accuracy and Computational Load of Fast 1D Models for Solar Receiver Parametric Studies
A big challenge consists in maximizing the thermal efficiency of volumetric solar receivers that are used to collect solar energy and heat-up a heat transfer fluid in renewable energy systems. Parametric studies provide an undisputed aid in early design stages and fast computational models are important to rapidly test novel configurations. In this paper, a comprehensive analysis to assess the accuracy and the computational load of 1D and 3D models compared to relevant literature data is presented. A 1D finite volume model and a 1D explicit model based upon the thermal resistance network are built by solving the solid and fluid energy balances and results are compared to accurate 3D CFD simulations of a solar receiver consisting of a silicon-carbide absorbing structure. The calculated air and solid temperatures are compared to literature findings on a receiver test geometry for different heat transfer fluid velocities. Results show that fast 1D models provide very accurate results with a maximum error of 2%-5% with respect to the reference in a computational time of few seconds, two order of magnitude lower than the one needed by accurate 3D CFD simulations.
- Open Access
- 4 February 2022
- Published by Wiley in Macromolecular Reaction Engineering
- Vol. 16 (6) , 2100058
FBR for Polyolefin Production in Gas Phase: Validation of a Two‐Phase Compartmentalized Model by Comparison with CFD
Two different modeling approaches are applied in this work to the simulation of fluidized bed reactors containing solid particles of Geldart A‐B type and operated at typical conditions for polyolefins production. On one side, a fully detailed computational fluid‐dynamics (CFD) model is developed, considering a 2D planar geometry and a multi‐fluid description with kinetic theory of granular flows. On the other, a conventional three‐phase, 1D compartmentalized model (SCM) is also developed, implementing the fluid dynamic description based on popular, semi‐empirical relationships available in the literature. Given the huge difference of computational effort associated with the corresponding numerical solutions, our aim is to confirm the reliability of the simplified model by comparison with the results of the detailed CFD model. The results show that the oversimplified compartmentalized approach is capable to predict the solid mixing features established inside the reactor operated in bubbling fluidization regime with good reliability for non‐reactive polyethylene particles. Average solid volume fractions are particularly close to the values predicted by the CFD model when monodisperse particles are considered inside the examined range of gas velocity values. A generally good agreement is also found when solids with broad size distribution are analyzed.
- 4 February 2022
- Published by Wiley in Macromolecular Reaction Engineering
- Vol. 16 (6) , 2100058
Open AccessFBR for Polyolefin Production in Gas Phase: Validation of a Two‐Phase Compartmentalized Model by Comparison with CFD
Two different modeling approaches are applied in this work to the simulation of fluidized bed reactors containing solid particles of Geldart A‐B type and operated at typical conditions for polyolefins production. On one side, a fully detailed computational fluid‐dynamics (CFD) model is developed, considering a 2D planar geometry and a multi‐fluid description with kinetic theory of granular flows. On the other, a conventional three‐phase, 1D compartmentalized model (SCM) is also developed, implementing the fluid dynamic description based on popular, semi‐empirical relationships available in the literature. Given the huge difference of computational effort associated with the corresponding numerical solutions, our aim is to confirm the reliability of the simplified model by comparison with the results of the detailed CFD model. The results show that the oversimplified compartmentalized approach is capable to predict the solid mixing features established inside the reactor operated in bubbling fluidization regime with good reliability for non‐reactive polyethylene particles. Average solid volume fractions are particularly close to the values predicted by the CFD model when monodisperse particles are considered inside the examined range of gas velocity values. A generally good agreement is also found when solids with broad size distribution are analyzed.