Michael J. Wadas

Data for the shock equation of state of helium are obtained up to 360 G Pa , nearly doubling the pressure of previous experimental measurements. The helium samples are first precompressed to 0.35–0.42 g c m − 3 in a diamond anvil cell prior to laser-driven shock compression at the Omega Laser Facility. Time-resolved Doppler velocimetry and pyrometry reveal significant reflectivity and greater compressibility compared to the predictions of existing broad-range tabular equation of state models, which may be caused by the onset of ionization. These experimental observations, however, are largely captured with molecular-dynamics simulations based on density functional theory, affirming the ability of first-principles techniques to capture complex physics, while enabling critical insight for the behavior of warm dense helium in Jovian interiors and white dwarf atmospheres.

The growth of three-dimensional perturbations subject to the Crow instability along a vortex dipole resulting from the passage of a shock wave through a heavy gaseous cylinder is examined numerically. A linear stability analysis is performed based on geometric parameters extracted from two-dimensional simulations to determine the range of unstable wavenumbers, which is found to extend from 0.0 to 1.3 when normalized by the core separation distance. The analysis is then verified by comparison to three-dimensional simulations, which clearly show the development of the instability and the pinch-off of the vortex dipole into isolated vortex rings, which manifest as clumps of the original cylinder material. A scaling law is developed to determine the relevant spatiotemporal scales of the instability development, which is then used to assess the feasibility of a high-energy-density experiment visualizing clump formation. Specifically, a shocked cylinder with an initial diameter of 100 μm consisting of a perturbation of approximate wavelength and amplitude of 600 and 10 μm, respectively, is expected to form clumps resulting from the Crow instability approximately 40 ns after it is shocked, with dynamics which can be readily visualized on the Omega EP laser facility.

An explanation for the origin and number of clumps along the equatorial ring of Supernova 1987A has eluded decades of research. Our linear analysis and hydrodynamic simulations of the expanding ring prior to the supernova reveal that it is subject to the Crow instability between vortex cores. The dominant wave number is remarkably consistent with the number of clumps, suggesting that the Crow instability stimulates clump formation. Although the present analysis focuses on linear fluid flow, future nonlinear analysis and the incorporation of additional stellar physics may further elucidate the remnant structure and the evolution of the progenitor and other stars.

The growth of perturbations subject to the Crow instability along two vortex rings of equal and opposite circulation undergoing a head-on collision is examined. Unlike the planar case for semi-infinite line vortices, the zero-order geometry of the flow (i.e. the ring radius, core thickness and separation distance) and by extension the growth rates of perturbations vary in time. The governing equations are therefore temporally integrated to characterize the perturbation spectrum. The analysis, which considers the effects of ring curvature and the distribution of vorticity within the vortex cores, explains several key flow features observed in experiments. First, the zero-order motion of the rings is accurately reproduced. Next, the predicted emergent wavenumber, which sets the number of secondary vortex structures emerging after the cores come into contact, agrees with experiments, including the observed increase in the number of secondary structures with increasing Reynolds number. Finally, the analysis predicts an abrupt transition at a critical Reynolds number to a regime dominated by a higher-frequency, faster-growing instability mode that may be consistent with the experimentally observed rapid generation of a turbulent puff following the collision of rings at high Reynolds numbers.

Structures evoking vortex rings can be discerned in shock-accelerated flows ranging from astrophysics to inertial confinement fusion. By constructing an analogy between vortex rings produced in conventional propulsion systems and rings generated by a shock impinging upon a high-aspect-ratio protrusion along a material interface, we extend classical, constant-density vortex-ring theory to compressible multifluid flows. We further demonstrate saturation of such vortex rings as the protrusion aspect ratio is increased, thus explaining morphological differences observed in practice.

In high-energy-density shock compression experiments, the desired state of compression is typically achieved by passing shock waves through a sequence of different materials. In this study, a theoretical approach for transiently strengthening such shocks passing through interfaces of experimentally relevant impedance ratios is examined. A semi-analytical method based on characteristics analysis is used to solve the problem of a shock passing from one material to another through an intermediate region of non-uniform impedance; by appropriately designing this region, a greater shock strength can be achieved in the second material for a finite duration than in the absence of this region. When a shock passes into a material of higher impedance, the shock strengthening increases to a maximum before decreasing to an asymptotic value as the strength of the incident shock is increased. For shocks passing into materials of decreasing impedance, the shock strengthening increases monotonically as the strength of the incident shock is increased when the impedance ratio is above a critical threshold. Incorporating multiple intermediate materials can further increase the strength of the transmitted shock, with an exponential discretization of intermediate material impedances being the most effective distribution for strengthening strong shocks. The results suggest that up to 25% and 9% increases in pressure behind the leading shock can be achieved for materials of increasing and decreasing impedance, respectively. The technique is applied to the design of laser-driven dynamic compression experiments, and the results of the analysis are verified via comparison to simulations performed with the HYADES hydrodynamics code.