Lin Tian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lin Tian has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Xinke Wu
College of Electrical Engineering, Zhejiang University, Hangzhou, China
4 shared publications - Jinxu Yang
College of Electrical Engineering, Zhejiang University, Hangzhou, China
3 shared publications Congrang Jiang
Shanghai Institute of Space Power-SourcesState Key Laboratory of Space Power-Sources Technology, Shanghai, China
1 shared publication- Faheem Muhammad
Zhejiang University
1 shared publication - Hui Liu
College of Electrical Engineering, Zhejiang University, Yuquan Campus, Hangzhou 310027, China
1 shared publication - Tianji Liu
College of Electrical Engineering, Zhejiang University, Hangzhou, China
1 shared publication
Latest Publications
- Open Access
- 25 June 2025
- Published by MDPI AG in Electronics
- Vol. 14 (13) , 2564
A Reduced-Order Small-Signal Model for Four-Switch Buck–Boost Under Soft-Switching Current Shaping Control Strategy
The four-switch buck–boost (FSBB) converter, which possesses both step-up and step-down capabilities, is highly suitable for applications where input and output voltages have overlapping ranges. Correspondingly, the current shaping control (CSC) strategy is investigated for the FSBB converter, which shapes a quadrilateral inductor current waveform featuring the minimum RMS value to improve efficiency and power density. However, the small-signal model for the CSC algorithm has not yet been established, and the traditional and common modeling method requires considering multiple duty cycles and phase shifts of the FSBB converter, whose calculation is complex and inconvenient to use. For the special case of the CSC strategy using cycle-by-cycle current detection, an additional constraint of the averaged volt-second on the inductor can be regarded as zero, making the inductor current no longer a variable of the state-space, which eliminates the pole generated by the inductor and reduces the order of the small-signal model. Thus, this paper greatly simplifies the computation and design of the compensator by using the constraint condition mentioned above. This one-pole first-order model is simplified, maintains enough accuracy in the low-frequency domain, and can be corrected using only a simple PI controller. Finally, a prototype of the 300 W FSBB converter under the digital CSC algorithm was built to validate the precision and dynamic performance of the proposed first-order small-signal model.
- 25 June 2025
- Published by MDPI AG in Electronics
- Vol. 14 (13) , 2564
Open AccessA Reduced-Order Small-Signal Model for Four-Switch Buck–Boost Under Soft-Switching Current Shaping Control Strategy
The four-switch buck–boost (FSBB) converter, which possesses both step-up and step-down capabilities, is highly suitable for applications where input and output voltages have overlapping ranges. Correspondingly, the current shaping control (CSC) strategy is investigated for the FSBB converter, which shapes a quadrilateral inductor current waveform featuring the minimum RMS value to improve efficiency and power density. However, the small-signal model for the CSC algorithm has not yet been established, and the traditional and common modeling method requires considering multiple duty cycles and phase shifts of the FSBB converter, whose calculation is complex and inconvenient to use. For the special case of the CSC strategy using cycle-by-cycle current detection, an additional constraint of the averaged volt-second on the inductor can be regarded as zero, making the inductor current no longer a variable of the state-space, which eliminates the pole generated by the inductor and reduces the order of the small-signal model. Thus, this paper greatly simplifies the computation and design of the compensator by using the constraint condition mentioned above. This one-pole first-order model is simplified, maintains enough accuracy in the low-frequency domain, and can be corrected using only a simple PI controller. Finally, a prototype of the 300 W FSBB converter under the digital CSC algorithm was built to validate the precision and dynamic performance of the proposed first-order small-signal model.
- Open Access
- 13 January 2025
- Published by MDPI AG in Electronics
- Vol. 14 (2) , 298
High-Frequency High-Magnetic Flux Variation Foil Winding AC Inductor Design with the Vertical Penetrating Magnetic Field Elimination
In traditional inductor design with planar windings, the magnetic field distribution may not be well-organized, leading to significant winding loss, particularly at high switching frequencies. This study explores the relationship between current distribution and magnetic field distribution in the winding region. Unlike conventional magnetic flux distribution, which directs a large portion of the magnetic field vertically through the windings in the winding region, this work introduces a structure that maintains most of the magnetic flux parallel to the foil windings through the application of quasi-distributed air gaps. This paper presents a design methodology for a high-frequency foil winding inductor with high flux variation. Building on this concept, a high-power density, low loss inductor with foil windings is designed based on the four-switch buck-boost (FSBB) converter. Experimental results demonstrate that the proposed inductor design significantly reduces winding loss in inductors with planar windings.
- 13 January 2025
- Published by MDPI AG in Electronics
- Vol. 14 (2) , 298
Open AccessHigh-Frequency High-Magnetic Flux Variation Foil Winding AC Inductor Design with the Vertical Penetrating Magnetic Field Elimination
In traditional inductor design with planar windings, the magnetic field distribution may not be well-organized, leading to significant winding loss, particularly at high switching frequencies. This study explores the relationship between current distribution and magnetic field distribution in the winding region. Unlike conventional magnetic flux distribution, which directs a large portion of the magnetic field vertically through the windings in the winding region, this work introduces a structure that maintains most of the magnetic flux parallel to the foil windings through the application of quasi-distributed air gaps. This paper presents a design methodology for a high-frequency foil winding inductor with high flux variation. Building on this concept, a high-power density, low loss inductor with foil windings is designed based on the four-switch buck-boost (FSBB) converter. Experimental results demonstrate that the proposed inductor design significantly reduces winding loss in inductors with planar windings.
- 18 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (10) , 12536-12546
Soft-Switching Control for a Resonant Four-Switch Inverting Buck–Boost DC/DC Converter With Wide Voltage Range
A resonant four-switch inverting buck-boost converter is a good choice for DC/DC applications that require an inverting voltage solution. A soft switching control scheme with four segments of resonance current has been examined using duty ratio and phase shift as control variables. As a result, the RMS value of the resonance current is low compared to DCM, which is directly proportional to the conduction loss. This control scheme allows the converter to regulate its output voltages more efficiently with soft switching operations. Thus, it contributes to an increment in efficiency improvement and board size reduction. At the same time, a simple close-loop is designed to meet the requirement of a wide voltage range with the corresponding simplified real-time PI control algorithm. For the verification of the proposed control scheme, a resonant four-switch inverting buck-boost DC/DC converter is designed and experimentally tested, which has recorded over 98.5% peak efficiency at a 1:1 inverting case (-48Vdc to 48Vdc). The converter's wide operating range is from -48Vdc to 28ni Vdc ∼ 60Vdc output voltage with a power density of 500W/in3.
- 18 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (10) , 12536-12546
Soft-Switching Control for a Resonant Four-Switch Inverting Buck–Boost DC/DC Converter With Wide Voltage Range
A resonant four-switch inverting buck-boost converter is a good choice for DC/DC applications that require an inverting voltage solution. A soft switching control scheme with four segments of resonance current has been examined using duty ratio and phase shift as control variables. As a result, the RMS value of the resonance current is low compared to DCM, which is directly proportional to the conduction loss. This control scheme allows the converter to regulate its output voltages more efficiently with soft switching operations. Thus, it contributes to an increment in efficiency improvement and board size reduction. At the same time, a simple close-loop is designed to meet the requirement of a wide voltage range with the corresponding simplified real-time PI control algorithm. For the verification of the proposed control scheme, a resonant four-switch inverting buck-boost DC/DC converter is designed and experimentally tested, which has recorded over 98.5% peak efficiency at a 1:1 inverting case (-48Vdc to 48Vdc). The converter's wide operating range is from -48Vdc to 28ni Vdc ∼ 60Vdc output voltage with a power density of 500W/in3.
- 19 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (8) , 7920-7929
A Simplified Real-Time Digital Control Scheme for ZVS Four-Switch Buck–Boost With Low Inductor Current
In this article, the four-switch buck–boost (FSBB) converter is a preferred choice for the dc–dc applications where the step-up and step-down are needed. In order to reduce the inductor size and improve the efficiency, the zero-voltage switch (ZVS) control schemes with four segments inductor current for FSBB have been investigated in numerous publications. Among these ZVS control schemes, the optimized control variable stored as the huge look-up table data achieved minimum root-mean-square (RMS) inductor current, and the complex real-time calculation is avoided. However, for the purpose of matching the wide input and output voltage ranges, an external flash is needed for storing the look-up table data; And the large time consumption for invoking the data hazard the dynamic performance significantly. To reduce the storage device cost and meet the demand of transient, a simplified real-time control algorithm is proposed by dividing the operation into the defined Discontinuous Conduction Mode (DCM) and Continuous Conduction Mode (CCM) operation featuring the minimum RMS inductor current and ZVS operation during the whole voltage range without complex calculation and mode transient. Finally, a 300 W dc–dc prototype is built to verify the theoretical analysis and proposed control scheme with a low-cost real-time digital controller.
- 19 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (8) , 7920-7929
A Simplified Real-Time Digital Control Scheme for ZVS Four-Switch Buck–Boost With Low Inductor Current
In this article, the four-switch buck–boost (FSBB) converter is a preferred choice for the dc–dc applications where the step-up and step-down are needed. In order to reduce the inductor size and improve the efficiency, the zero-voltage switch (ZVS) control schemes with four segments inductor current for FSBB have been investigated in numerous publications. Among these ZVS control schemes, the optimized control variable stored as the huge look-up table data achieved minimum root-mean-square (RMS) inductor current, and the complex real-time calculation is avoided. However, for the purpose of matching the wide input and output voltage ranges, an external flash is needed for storing the look-up table data; And the large time consumption for invoking the data hazard the dynamic performance significantly. To reduce the storage device cost and meet the demand of transient, a simplified real-time control algorithm is proposed by dividing the operation into the defined Discontinuous Conduction Mode (DCM) and Continuous Conduction Mode (CCM) operation featuring the minimum RMS inductor current and ZVS operation during the whole voltage range without complex calculation and mode transient. Finally, a 300 W dc–dc prototype is built to verify the theoretical analysis and proposed control scheme with a low-cost real-time digital controller.