Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Christos Georgios Aneziris has a total of 61 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Additive Manufacturing of Layered Nb-Al2O3 Composite Granules Based on Paste Extrusion

    by Tilo Zienert, Dinesh Kumar Gunasekar, Dirk Endler, Christina Faßauer, Christos G. Aneziris

    How would it be possible to functionalize ceramic aggregates for use in refractories? In this work, we demonstrate how paste extrusion can be used to fabricate layered and porous Nb-Al2O3-based composite refractories for adjusting thermal and electrical conductivity. Additive manufacturing is used to generate a specific sequence of alumina and composite layers. After drying, the samples were sintered at 1600 °C, crushed, and sieved into particle sizes up to 3150 µm. The rheology of the paste revealed the intended shear-thinning behavior with microcrack formation between the yield and flow strain. The sintered material showed promising thermal-shock characteristics reaching plateau values after the third cycle without signs of further structural damage up to the fifth thermal shock. The layered microstructure was retained after crushing the composites, establishing functionalization of the refractory granules for all particle sizes.


  • Open Access

    Thermal Expansion of Electrofused MgO-Based Spinel Systems Containing Fe2O3, Al2O3-Fe2O3, Al2O3-Cr2O3-Fe2O3 and Al2O3-NiO-Fe2O3

    by Tilo Zienert, Otávio H. Borges, Victor C. Pandolfelli, Christos G. Aneziris

    Magnesia-spinel multicomponent materials have been used as refractories for a long time. In addition to a few binary systems, the influence of spinel phases on the thermal expansion (α) of MgO or the resulting compound has not been studied so far. As α is critical for refractories in application, this work investigates the thermal expansion of complex MgO-based spinel systems using X-ray diffraction (XRD) in combination with Rietveld refinement in the temperature range between 30 °C and 1200 °C. All studied periclase solid solutions, in contact with spinels of the systems Mg1.01(Al0.23Cr1.64Fe0.13)O4, Fe3O4–MgFe2O4, NiFe2O4–NiAl2O4, MgAl2O4–MgFe2O4, Fe3O4–FeAl2O4 and Fe3O4·NiFe2O4·2MgAl2O4 showed α trends below plain MgO, or even decreasing values above 1000 °C. Many spinels showed large negative thermal expansion coefficients. It was found that the structural change in spinels is constrained, leading to a common analytical expression to calculate the lattice parameter of spinels with temperature, which was used to study the nature of the investigated spinels in more detail. The work highlights that Cr-free MgO-spinel systems show similar or even better high-temperature behaviour than commonly used magnesia–chrome aggregates.


  • Open Access

    Employing miniaturized test methods to determine high-temperature strength of carbon-bonded alumina

    by Shahin Takht Firouzeh, Martin Abendroth, Tony Wetzig, Christos G. Aneziris, Bjoern Kiefer

  • Open Access

    Towards High-Quality Investment Casting of Ti-6Al-4V with Novel Calcium Zirconate Crucibles and Optimized Process Control

    by Florian Bulling, Ulrich E. Klotz, Alexander Heiss, Lisa Freitag, Christina Faßauer, Christos G. Aneziris

    The investment casting of titanium and its alloys relies on a high resistance of the crucibles and shell molds in terms of temperature and reactivity. The availability of ceramic crucibles that offer sufficient resistance to the titanium melt enables vacuum induction melting (VIM). CaZrO3 prepared from a mixture of CaO and ZrO2 as a raw material for refractory ceramics shows a high corrosion resistance against metallic melts even under very high temperatures up to 1800 °C. Crucibles and shell molds of CaZrO3 were successfully produced and used in subsequent casting trials. This study is focused on the refractory crucibles suitable for casting Ti-6Al-4V (Ti-64) using a tilt casting machine. In order to evaluate the crucible reaction and, therefore, the quality of the castings, chemical analyses, investigations of the microstructures and hardness measurements were carried out. Careful control of the melting duration is mandatory to avoid crucible reactions that otherwise result in contamination of the cast with oxygen and zirconium. This was achieved by modified coil geometries. Under optimized casting conditions, the oxygen and zirconium impurity limits of ASTM B367-09 for titanium castings were met. Based on the correlations found, optimized casting parameters with regard to material quantity, coil geometry and heating power could be determined in order to provide guidance for a high-quality casting process with VIM.


  • Open Access

    Ceramic Filter Materials and Filter Structures with Active and Reactive Functional Pores for the Aluminum Melt Filtration

    by Claudia Voigt, Tony Wetzig, Jana Hubálková, Patrick Gehre, Nora Brachhold, Christos G. Aneziris

    The application of ceramic foam filters is state of the art in the casting of aluminum melt. Despite their industrial use since the 1960s, the filtration mechanisms are not fully understood. The Collaborative Research Center 920 investigated the influence of the filter surface chemistry and wetting between filter and melt on the filtration efficiency. The investigated filter surfaces based on Al2O3, MgAl2O4, 3Al2O3·2SiO2and TiO2 showed differences in the filtration efficiency and the wetting behavior whereby a good correlation for inclusions smaller than 110 µm was found–the larger the contact angle the higher the filtration efficiency. The results raised the question whether the intrinsic contact angle or the different roughness of the materials caused the changes in the filtration efficiency. A filtration trial at the Hydro pilot filtration line revealed a strong influence of the filter surface roughness on the filtration efficiency. A filter coated with Nano-Al2O3, with a divergent intrinsic contact angle compared to be Al2O3 reference filter, showed no improvement of the filtration behavior indicating no influence of the intrinsic contact angle on the filtration.

  • Open Access

    Cleanness of Molten Steel—Active and Reactive, Exchangeable Filter Systems for the Continuous Casting of Steel

    by Tony Wetzig, Andreas Baaske, Sven Karrasch, Steffen Dudczig, Christos G. Aneziris

    The filtration of steel melts in the continuous casting of steel is of special interest in order to meet the ever-increasing purity requirements regarding the metal’s purity. Due to the high mass flow and the high casting duration, the application of in-built filters in the tundish system is rather challenging, especially regarding the filter capacity. In the framework of this contribution, a new concept involving the immersion of filters into the steel melt from above the tundish was investigated. This approach allows for the flexible exchange of used filters without interruption of the underlying process. At the Institute of Ceramics, Refractories and Composite Materials, carbon-bonded alumina filters on the basis of established slurry compositions and modified replication techniques were scaled up for the industrial application in continuous casting of steel. The best property profile was observed for a triple coating approach based on centrifugation, dip coating and spray coating. In the tundish of a steel casting simulator, a lab-scale casting test was conducted in order to check the thermos-mechanical behavior of the filter in contact with molten steel. After the successful evaluation in lab scale, the filters were tested in industrial trials in cooperation with the company thyssenkrupp Steel Europe AG. A ladle casting with immersed filter lasted approximately 45 min with a static casting speed of 8 to 10 t/min and a melt temperature of above 1550 °C. The filters were analyzed for inclusions and potential damage at the Institute of Ceramics, Refractories and Composite Materials. Dense clogging layers on the filter surface were identified as in-situ layers as usually observed in lab-scale steel casting simulator tests in consequence of reactive filtration effects. Furthermore, inclusion clusters which were removed at the filter bottom due to the direct inflow in consequence of the buoyancy were observed as signs of active filtration. A further alternative to foam filters is presented by gel-cast spaghetti filter structures with mechanically robust full-strut structure. In the subproject T01K, the gel casting process was optimized in order to realize the necessary upscaling of the components. With the aid of alginate-based gel casting, spaghetti filter with organized lattice structures were manufactured and tested. Steel casting simulator trials showed favorable behavior in contact with the melt.

  • Open Access

    In Situ Observation of Collision Between Exogenous and Endogenous Inclusions on Steel Melts for Active Steel Filtration

    by Christina Schröder, Xingwen Wei, Undine Fischer, Gert Schmidt, Olena Volkova, Christos G. Aneziris

    Investigations at the high-temperature confocal laser scanning microscope (HT-CLSM) allow observing the interaction of non-metallic particles in terms of potential filter material with endogenous particles of molten steel in the high-temperature range. The respective particle velocities are determined from the particle movements and conclusions are drawn about the attractive forces of the particles. The interactions of exogenous Al2O3 particles, MgO and MgAl2O4 spinel particles, and CA6 calcium aluminate particles with endogenous constituents of molten steel X15CrNiSi25-20 are analyzed in the present work. Accompanying experiments were performed in a heating microscope on the interaction between steel and MgO and steel and CA6. Scanning electron microscopy SEM/EDX/EBSD studies reveal not only the interactions of the non-metallic inclusions with each other, but also reactions of the molten steel with the exogenous particles that affect the agglomeration behavior. While exogenous and endogenous Al2O3 particles exhibit high attractive forces and almost no react with the molten steel, a liquid reaction layer forms around the magnesia particles, which leads to a reduction of the attractive forces. After dissolution of the reaction layer, the attractive forces increase. Spinel particles are surrounded by a strong meniscus in the observed steel melt. Endogenous particles moving toward the spinel do not adhere to the particle. Reactions were also observed when CA6 particles came into contact with molten steel. In this process, the calcium aluminate is depleted of calcium. Only loose connections of the exogenous Ca-depleted CA6 with endogenous Al2O3 particles have been detected.


  • Open Access

    Qualitative and Quantitative X-ray Tomography of Filter Macrostructures and Functional Components

    by Jana Hubálková, Christos G. Aneziris

    This chapter focuses on the application of a conventional attenuation based X-ray computed tomography for the investigation of porous and dense structural components in different stages of the manufacturing process and loading. Firstly, the image acquisition process, image processing and qualitative evaluation are introduced using reticulated foam filter and a nozzle component as examples. Secondly, the quantification strategies of the reconstructed volume data involving segmentation of targeted features and its geometrical characterization are presented. Thirdly, the issue of ex-situ investigations is outlined and discussed using differently sized carbon-bonded alumina filters subjected to thermomechanical loading. Fourthly, the interrupted in-situ compression testing of glass foam structures is demonstrated. Finally, the benefits and limitations of conventional X-ray computed tomography as analysis method for porous and dense materials are emphasized.


  • Open Access

    Functionalized Feeders, Hollowware, Spider Bricks and Starter Casting Tubes for Increasing the Purity in Steel Casting Processes

    by Tony Wetzig, Matthias Schwarz, Leandro Schöttler, Patrick Gehre, Christos G. Aneziris

    Although continuous casting became the state of the art for the casting of ordinary steel grades, ingot casting by bottom teeming still has relevance in the steelmaking industry, especially for the manufacturing of specialty and alloy steels. As for every casting process, the ever-increasing quality requirements by customers lead to increased demand for new technologies to increase the purity of the cast steel melt regarding its inclusion content. Due to the special design of the bottom-teeming ingot casting facility and the discontinuous operation as batch process, the application of filters is a promising approach. Tailored foam geometries were prepared based on additive manufacturing via selective laser sintering (SLS) and transformed into filters via modified replication techniques and flame spraying. Additionally to filter application, the functionalization and quality improvement of applied hollowware refractories has high potential to remove existing inclusions from the steel melt and avoid the formation of new inclusions during casting. The investigated hollowware components were manufactured by pressure slip casting on the basis of coarse-grained alumina compositions and subsequent functionalization by spray coating based on carbon-bonded alumina slurries. Simultaneous application of functionalized, “reactive” refractory components and flame-sprayed, “active” filters enables a combined filtration system which unites the advantages of the distinct filtration mechanisms. In the continuous casting of specialty steels, the conditions are more severe resulting in additional challenges regarding the application of filters. An approach investigated in this subproject is the use of extruded filter starter casting tubes above the tundish outlet. To achieve this, extrusion mixes based on cellulose derivatives and materials of the system Al2O3-ZrO2-C (AZC) were investigated for their suitability. The new concepts were tested in industrial casting trials in cooperation with the company Deutsche Edelstahlwerke Specialty Steels Europe GmbH (DEW). Post-mortem, the former melt-refractory interface of the applied components was investigated and steel samples from the ladle, the gating system and the ingot were analyzed in comparison to untreated samples.

  • Open Access

    Novel Ceramic Foam Filter Materials for the Filtration of Magnesium Alloy Melts

    by Alina Schramm, Christos G. Aneziris, Christiane Scharf

    Cleanliness of magnesium alloy melts plays an important role in producing high-quality, lightweight products exemplary for the automotive or aircraft industry with high-quality standards. Therefore, the applicability of ceramic foam filters in the active and reactive filtration of magnesium alloys was explored as an option of metallurgical refining. Carbon-bonded alumina foams were selected in their uncoated as well as variously coated states. To evaluate the applicability of selected ceramic filter materials, various tests were applied, investigating filter properties, interface interactions, melt cleanliness and wetting behavior of the filter, such as sessile drop tests, immersion and filtration tests, and metallographic evaluation of AZ91. Immersion tests in AZ91 at 680 °C for up to 60 min showed the durability of coated and uncoated Al2O3-C and the formation of finely-structured MgO in-situ layers on any alumina- or spinel-containing surfaces in contact with molten AZ91. These layers, resulting from interface reactions with the melt, are regarded to have the potential to attract and bind oxidic inclusions from the metallic melt during filtration, as AZ91 samples showed reduced inclusion amounts after their contact with Al2O3-C filters. Another milestone was the synthesis of MgAlON as a filter coating, proven to be resistant towards the reactive magnesium alloy melt.