YLYibo Liu

Yibo Liu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yibo Liu has a total of 15 co-authors. Here are the top co-authors by number of shared publications:

  • Baojia Chen

    Hubei Key Laboratory of Hydroelectric Machinery Design & Maintenance Three Gorges University Yichang China

    2 shared publications
  • Bo Tao

    Wuhan University of Science and Technology

    2 shared publications
  • Nannan Sun

    Technology research and development Huaxia Xingguang Industrial Design Jiangsu Co., Ltd. Suqian China

    2 shared publications
  • Yongcheng Cao

    Technology Research and Development Hubei Jingmen Wusan Machinery Equipment Manufacturing Co., Ltd. China

    2 shared publications
  • Chengcheng Li

    Key Laboratory of Metallurgical Equipment and Control Technology of Ministry of Education Wuhan University of Science and Technology Wuhan China

    1 shared publication
  • Dou An

    Department of Automation Science and Technology, Xian Jiaotong University, Xian, China

    1 shared publication

Latest Publications

  • Manipulator trajectory planning based on work subspace division

    by Yibo Liu, Fan Xiao, Xiliang Tong, Bo Tao, Manman Xu, Guozhang Jiang, Baojia Chen, Yongcheng Cao, Nannan Sun

    The manipulator workspace is an essential element in the field of manipulator research and is of great significance for manipulator motion planning. However, little research has been conducted on dividing the manipulator workspace into working subspaces. No precise division method has been proposed; the inverse kinematics of multiple solutions in manipulator trajectory planning may also cause abrupt joint changes, thus affecting the planned trajectory. The article proposes a working subspace division method for all ball‐wrist 6DOF(degree‐of‐freedom) manipulators that satisfy the Piper criterion to address the above problems. The kinematic model of the manipulator is established, and the Jacobi matrix of the manipulator is obtained. The space of joints of the manipulator is divided into unique domains containing only single inverse kinematic solutions by means of singular trajectory lines when the determinant of the Jacobi matrix is zero; The solution from the joint space to the workspace is achieved by a nonlinear mapping, which completes the partitioning of the work subspace, and each work subspace contains only unique inverse kinematic solutions. When trajectory planning is carried out from the independent area of a single workspace to the overlapping area of multiple workspaces, selecting the inverse kinematic solution in a single working subspace can effectively avoid abrupt changes in the joints of the manipulator and trajectory misalignment caused by numerous inverse solution selection problems and make the planned trajectory smooth and consistent with the operational requirements of each scene.


  • Wrist angle prediction under different loads based on GA‐ELM neural network and surface electromyography

    by Yibo Liu, Chengcheng Li, Du Jiang, Baojia Chen, Nannan Sun, Yongcheng Cao, Bo Tao, Gongfa Li

    In sEMG (surface electromyography) pattern recognition, most of the research focuses on the static pattern recognition of different limbs, ignoring the importance of changing load intensity, and joint angle movement information. Traditional static qualitative pattern recognition cannot adjust the motion amplitude and load intensity, so it is of great significance to study the continuous prediction of wrist angle under different load intensities. Based on the correlation between the surface EMG signal and the joint angle signal, the article is based on the neural network to identify and predict the wrist angle under different loads continuously quantitatively. The sEMG signal in this article was collected with the approval and review of the Ethics Committee and the people's informed consent. Since qualitative pattern recognition cannot adjust the wrist movement range and the different load training intensity, the article establishes an angle prediction model based on a genetic algorithm to optimize the extreme learning machine (ELM). In addition, the article analyzes the influence of different loads on the continuous prediction accuracy of the wrist angle, realizes the continuous quantitative angle of the precise wrist prediction. Experimental analysis shows that the wrist joint angle predicted by the ELM optimized based on genetic algorithm is close to the actual angle, and the average error is about 5.96 degrees.


  • An improved fault diagnosis method based on deep wavelet neural network

    by Yibo Liu, Qingyu Yang, Dou An, Yongqiang Nai, Zhiqiang Zhang

    Deep learning has been successfully applied to the field of fault diagnosis in recent years. Due to the advantages of deep belief network (DBN) in fitting nonlinear complex systems and the ability of wavelet analysis in time-frequency analysis, in this paper, an improved fault diagnosis method based on a deep wavelet neural network (DWNN), which combines the DBN with morlet activation functions, is proposed for fault diagnosis of reciprocating compressor. A five-layer DBN using sigmoid, tanh, rectified linear unit (ReLU) and morlet wavelet functions as the activation functions of hidden layers separately is proposed for fault diagnosis of reciprocating compressor. As the contrast, a three-layer back propagation neural network (BPNN) using the same four activation functions separately is proposed for fault diagnosis of reciprocating compressor. The experimental results show that, the fault diagnosis rate of five-layer DBN is higher than the three-layer BPNN. The method based on DWNN can make the fault diagnosis rate reach 100% within short time. Compared with using other activation functions, the DWNN architecture requires less epochs to train the model.