Jing Di

In this paper, long-term loading tests of ten prestressed glulam beams were carried out for 45 days, using the loading method of three-point hanging heavy objects. We analyzed the influence of prestressed steel wire numbers and total preloading force on parameters such as failure mode of beams, variation of steel wire stress, and long-term deflection of mid-span. When the total prestress was constant and the number of steel wires was 2, 4, and 6, the total stress of steel wires decreased by 33.07%, 37.26%, and 50.04%, respectively, after long-term testing for 45 days. The ratio of mid-span deflection to total deflection was 61.5%, 54.8%, and 40.9% respectively. When the number of steel wires was constant and the values of total prestress were 0, 3.079 kN and 6.158 kN, the total stress decreased by 28.90%, 36.59%, and 36.63%, respectively, after long-term loading. The ratio of long-term deflection of mid-span to total deflection was 60.7%, 54.8%, and 39.3%, respectively. The more steel wires, the greater the value of total prestress and the loss of total stress, the smaller the mid-span long-term deflection. After the test, we analyzed and fitted the test data to obtain the specific numerical of the creep coefficient θ under normal conditions, and the formula for calculating the long-term stiffness of the glulam beams based on the creep effects is proposed.

This paper describes experimental and numerical investigations on a new type of strengthened light-wood-framed (LWF) shear wall (SW) that has parallel strand bamboo (PSB) panels at each end. The experiments are divided into two parts: (1) monotonic loading tests of panel-to-frame joints representing different positions along the wall; (2) monotonic loading tests of a group of traditional full-scale SWs and two groups of strengthened walls with nailed or screwed PSB panels. The failure modes, load–displacement curves, ultimate bearing capacity, elastic stiffness, and dissipation are analyzed, and the mechanical properties of panel-to-frame joints and the lateral performance of SWs are discussed. Moreover, nonlinear finite-element analysis shows that the numerical results are in good agreement with the test results. Our findings suggest that using LWF SWs strengthened with nailed PSB panels effectively improves the failure mode and the ductility, stiffness, and dissipation of traditional walls. Using sheathing screws on the PSB panels increases the lateral bearing capacity and the dissipation of the walls, but decreases their ductility ratio. Setting end PSB panels improves the overturning resistance capacity by restricting the uplift of studs. The LWF SWs strengthened with end PSB panels are found to meet the design requirements and reduce construction costs.

To exploit the spruce-pine-fir (SPF) panel and the parallel strand bamboo (PSB) panel used in light wood framed shear wall and investigate the lateral behaviors of frame-to-sheathing joints in light wood framed shear wall with different characteristics, the experimental investigation and reliability analysis were carried out under monotonic load. The test configurations included joints with perpendicular-to-framing-grain load or parallel-to-framing-grain load, with SPF sheathing panel or PSB sheathing panel and with nail or screw. The results suggested that nailed joints with PSBpanel occurred ductile failure but other joints occurred brittle failure. Moreover, theultimate bearing capacity and the elastic stiffness of the joints under perpendicular load were higher than that ofthe joints under parallel load. The use of PSB panel and screw increased theultimate bearing capacity of the joints. Furthermore, based on Johansen yield theory and experimental results, the reliability analysis was carried out through first-order reliability methods. The results showed that the SPF-nail joints, the PSB-nail joints, and PSB-screw joints achieved the reliability requirements.

Purpose: In view of the defects of glued wood beams, a new composite member – reconstituted bamboo board reinforced glued wood beams is proposed to improve the bearing capacity of glued wood beams.Design/methodology/approach: The bending test studied the ordinary glulam beams and the reinforced glulam beams with different layer numbers and different layer thicknesses by comparing with six kinds of glulam beams strengthened with bamboo scrimber and one kind of ordinary glulam beams and used the method of third-point stepwise loading on the glulam beams strengthened with bamboo scrimber.Findings: The bamboo scrimber improved the bending behavior of the ordinary glulam beams. The 10 mm bamboo scrimber layer can meet the requirements of the maximum ultimate bending capacity and minimize the defects. So 10 mm bamboo scrimber layer was the optimal thickness. During the loading process, the strain change of the normal section of the reconstituted bamboo board reinforced glued wood beam basically conforms to the plane section assumption.Originality/value: The bending rigidities of the glulam beams strengthened with bamboo scrimber increased up to 28.25%, 8.53% and 76.67%, and the ultimate bending capacity increased from 83.44% to 99.34% with the increase of the bamboo scrimber plate layers (the replacement rate). The ultimate bending capacities and the bending rigidities of the glulam beams strengthened with bamboo scrimber increased to 52.32%∼60.18% and 90.07%∼99.34% with the changing of the bamboo scrimber thicknesses from 7.1 mm to 25 mm.

Purpose: The sheathing panels of traditional light wood frame shear walls mainly use oriented strand board (OSB) panels, and the damage of the traditional walls is mainly caused by the tear failure at the bottom corner of the OSB panel. In order to improve the lateral performance of the traditional light wood frame shear wall, a new type of end narrow panels reinforced light wood frame shear wall is proposed.Design/methodology/approach: The monotonic loading tests and finite element analysis of nine groups of walls, with different types of end narrow panel, types of fasteners used on the end narrow panels and the end narrow panels edge fastener spacing, are carried out. The effects of different characters on lateral performance of light wood frame shear walls are reported and discussed.Findings: The failure modes of the wall reinforced by parallel strand bamboo narrow panels with 150 mm edge nails spacing are similar to the traditional wall. Conversely, the failure modes of other groups of walls reinforced by end narrow panels are the tears of the bottom narrow panel or the bottom beam. The end narrow panel reinforced light wood frame shear wall can make full use of the material property of sheathing panels. Compared with the lateral performance of traditional walls, the new-type end narrow panels reinforced walls have better lateral performance.Originality/value: A new type of end narrow panels reinforced light wood frame shear wall is proposed, which can enhance the lateral performance of the traditional light wood frame shear wall. The new-type walls have advantages of convenient operation, manufacture cost saving and important value of engineering application.

The seismic performance of a light wood frame structure is determined by sheathing-to-framing joints. In order to encourage the use of more sustainable materials in structures, the spruce-pine-fir (SPF) panel and the bamboo scrimber (BS) panel were considered as sheathing materials. Monotonic and cyclic tests were conducted on the joints with different parameters to obtain their mechanical properties. Moreover, the design value of the bearing capacity of sheathing-to-framing joints was calculated and compared in accordance with Chinese code (GB50005) and European code (Eurocode 5). Based on the test results and the design codes, the reliability index of the design value of the bearing capacity of joints was calculated using the first-order reliability method (FORM). Results demonstrate that the joints have high bearing capacity and stiffness at initial loading stage when the loading direction is perpendicular to the framing grain. BS panels make better use of the bending strength of fasteners than SPF panels. The screwed joints have lower strength and stiffness degradation than nailed joints, but the nailed joints show better ductile and dissipation than screwed joints. In addition, the reliability indexes of design bearing capacity calculated by the Chinese code of joints under monotonic load are conservative, but those of joints under cyclic load are unconservative. Therefore, in order to ensure the safety and economy of design, a modification factor for the GB50005 design method of joints is proposed to meet the target reliability index.