Kirill Ostrovnoy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kirill Ostrovnoy has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Vitaliy Tyukanko
Department of Chemistry and Chemical Technology, M. Kozybayev North Kazakhstan University, Petropavlovsk 150000, Kazakhstan
3 shared publications - Alexandr Demyanenko
Department of Chemistry and Chemical Technology, M. Kozybayev North Kazakhstan University, Petropavlovsk 150000, Kazakhstan
2 shared publications - Antonina Dyuryagina
Manash Kozybayev North Kazakhstan University
2 shared publications A. N. Dyuryagina
Kozybaev North Kazakhstan State University
1 shared publication- A. S. Zhabina
Manash Kozybayev North Kazakhstan University NPLC
1 shared publication - Aida Lutsenko
Manash Kozybayev North Kazakhstan University
1 shared publication
Latest Publications
- Open Access
- 23 December 2024
- Published by Non-profit limited company "Manash Kozybayev North Kazakhstan University" in Vestnik of M. Kozybayev North Kazakhstan University
- No. 4 (64),p. 35-42
Preparation of lignosulfonic acid salts by sulfite cooking of used non-condensing wood
This article is devoted to the production of lignosulfonic acid salts by sulfite cooking. Lignosulfonates are important organic compounds that have unique surface-active properties and are widely used in various industries. The article analyzes the main stages of the preparation and separation of lignosulfonates. The possibilities of the synthesis of lignosulfonic acid salts and the potential of their use as additives in water-soluble paints and varnishes are described. The positive effect of the lignosulfonate content on the change in the surface tension of water-acrylic dispersions is shown. Based on the obtained synthesis results, the yield of sodium lignosulfonate was calculated and a technical and economic calculation of the cost of producing 10 kg of the product was performed.
- 23 December 2024
- Published by Non-profit limited company "Manash Kozybayev North Kazakhstan University" in Vestnik of M. Kozybayev North Kazakhstan University
- No. 4 (64),p. 35-42
Open AccessPreparation of lignosulfonic acid salts by sulfite cooking of used non-condensing wood
This article is devoted to the production of lignosulfonic acid salts by sulfite cooking. Lignosulfonates are important organic compounds that have unique surface-active properties and are widely used in various industries. The article analyzes the main stages of the preparation and separation of lignosulfonates. The possibilities of the synthesis of lignosulfonic acid salts and the potential of their use as additives in water-soluble paints and varnishes are described. The positive effect of the lignosulfonate content on the change in the surface tension of water-acrylic dispersions is shown. Based on the obtained synthesis results, the yield of sodium lignosulfonate was calculated and a technical and economic calculation of the cost of producing 10 kg of the product was performed.
- Open Access
- 29 June 2024
- Published by Shakarim University in Bulletin of Shakarim University. Technical Sciences
- Vol. 1 (2(14)) , 519-527
FEATURES OF THE CHEMICAL COMPOSITION AND PRODUCTION OF SAPROPEL IN EUTROPHIC LAKES OF THE NORTH KAZAKHSTAN REGION
The bottom sediments of the eutrophic lakes of the North Kazakhstan region are distinguished by the presence of sapropel, which can be used in agriculture. To create an effective technology for processing sapropels, it is necessary to know the features of their chemical composition, which ultimately affects the indicators of the sowing qualities of crop seeds. Based on the study of the chemical composition of the bottom sediments of three eutrophic lakes, a raw source for the production of sapropel with optimal organic and mineral composition is identified in this article. A method for processing bottom sediments is proposed. The resulting sapropel product is used for pre-sowing treatment of vegetable seeds. The results of chemical analysis of organomineral bottom sediments of three eutrophic lakes of the Kyzylzhar district of the North Kazakhstan region showed that the bottom sediments of Lake Penkovskoye are characterized by an increased content of organic matter, humus and mineral composition necessary for plant growth and development. The possibility of separating sapropelic product from bottom sediments of eutrophic lakes is shown. Laboratory tests conducted on the variable use of sapropel product, beet seeds of the Bordeaux 237 variety for germination and germination energy showed that the content of 1.6 g /dm3 in sapropel solution is sufficient to increase the germination energy of vegetable seeds by 2 times, and germination by more than 50%.
- 29 June 2024
- Published by Shakarim University in Bulletin of Shakarim University. Technical Sciences
- Vol. 1 (2(14)) , 519-527
Open AccessFEATURES OF THE CHEMICAL COMPOSITION AND PRODUCTION OF SAPROPEL IN EUTROPHIC LAKES OF THE NORTH KAZAKHSTAN REGION
The bottom sediments of the eutrophic lakes of the North Kazakhstan region are distinguished by the presence of sapropel, which can be used in agriculture. To create an effective technology for processing sapropels, it is necessary to know the features of their chemical composition, which ultimately affects the indicators of the sowing qualities of crop seeds. Based on the study of the chemical composition of the bottom sediments of three eutrophic lakes, a raw source for the production of sapropel with optimal organic and mineral composition is identified in this article. A method for processing bottom sediments is proposed. The resulting sapropel product is used for pre-sowing treatment of vegetable seeds. The results of chemical analysis of organomineral bottom sediments of three eutrophic lakes of the Kyzylzhar district of the North Kazakhstan region showed that the bottom sediments of Lake Penkovskoye are characterized by an increased content of organic matter, humus and mineral composition necessary for plant growth and development. The possibility of separating sapropelic product from bottom sediments of eutrophic lakes is shown. Laboratory tests conducted on the variable use of sapropel product, beet seeds of the Bordeaux 237 variety for germination and germination energy showed that the content of 1.6 g /dm3 in sapropel solution is sufficient to increase the germination energy of vegetable seeds by 2 times, and germination by more than 50%.
- Open Access
- 28 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (6(115)) , 31-42
Modeling the wetting of titanium dioxide and steel substrate in water-borne paint and varnish materials in the presence of surfactants
This paper reports the results of studying the effect of two additives such as polyether siloxane (PS) and sodium polyacrylate (SPA) on the wetting of various substrates in water-borne paints (WB paints). Titanium dioxide (TiO2), paraffin (PA), steel (ST), and glass (GL) were used as solid substrates. The edge wetting angle (θ0) and the ratio (dCosθ/dСS) were used as the criterion for assessing the wettability of solid substrates. In aqueous solutions (without acrylic resin), both surfactants improve the wetting of the substrates. For PS, all the substrates studied, depending on θ depression, can be arranged in a row: ST>PA>GL>TiO2. For SPA: PA>TiO2>GL>ST. The introduction of an acrylic film-forming agent in the composition enhances the wetting ability of SPA (in comparison with the aqueous solution of surfactants). With an increase in the concentration of SPA from 0 to 4 g/dm3 in acrylic resin solutions, the edge wetting angle of steel decreases by 6÷8° (while in water by only 3°). With respect to TiO2, the wetting activity of SPA does not depend on the acrylic content of the water. PS in acrylic-containing compositions exhibits worse wetting activity than SPA. The introduction of surfactants in the compositions improves the quality of coatings. With optimal SPA contents in the compositions, the corrosion rate of coatings is reduced (in distilled water by 45 %, in 60 % NaCl solution by 60 %). At the same time, the gloss of coatings increases by 50 % while adhesion increases by 2 points (according to ISO 11845: 2020). This is fully correlated with the nature of the effect of surfactants on the wetting of the steel substrate and pigment (titanium dioxide). Based on probabilistic-deterministic planning, the compositions of WB paints were optimized, ensuring their maximum wetting of TiO2 and ST. Equations for calculating cosθ depending on the content of acrylic polymer and surfactants have been derived
- 28 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (6(115)) , 31-42
Open AccessModeling the wetting of titanium dioxide and steel substrate in water-borne paint and varnish materials in the presence of surfactants
This paper reports the results of studying the effect of two additives such as polyether siloxane (PS) and sodium polyacrylate (SPA) on the wetting of various substrates in water-borne paints (WB paints). Titanium dioxide (TiO2), paraffin (PA), steel (ST), and glass (GL) were used as solid substrates. The edge wetting angle (θ0) and the ratio (dCosθ/dСS) were used as the criterion for assessing the wettability of solid substrates. In aqueous solutions (without acrylic resin), both surfactants improve the wetting of the substrates. For PS, all the substrates studied, depending on θ depression, can be arranged in a row: ST>PA>GL>TiO2. For SPA: PA>TiO2>GL>ST. The introduction of an acrylic film-forming agent in the composition enhances the wetting ability of SPA (in comparison with the aqueous solution of surfactants). With an increase in the concentration of SPA from 0 to 4 g/dm3 in acrylic resin solutions, the edge wetting angle of steel decreases by 6÷8° (while in water by only 3°). With respect to TiO2, the wetting activity of SPA does not depend on the acrylic content of the water. PS in acrylic-containing compositions exhibits worse wetting activity than SPA. The introduction of surfactants in the compositions improves the quality of coatings. With optimal SPA contents in the compositions, the corrosion rate of coatings is reduced (in distilled water by 45 %, in 60 % NaCl solution by 60 %). At the same time, the gloss of coatings increases by 50 % while adhesion increases by 2 points (according to ISO 11845: 2020). This is fully correlated with the nature of the effect of surfactants on the wetting of the steel substrate and pigment (titanium dioxide). Based on probabilistic-deterministic planning, the compositions of WB paints were optimized, ensuring their maximum wetting of TiO2 and ST. Equations for calculating cosθ depending on the content of acrylic polymer and surfactants have been derived
- Open Access
- 31 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (6(112)) , 41-50
Optimization of titanium dioxide wetting in alkyd paint and varnish materials in the presence of surfactants
This paper reports the results of studying the influence of surfactants (SAS) on the wetting of titanium dioxide in alkyd paint and varnish materials (PVM), based on pentaphthalic (PPh) and alkyd-urethane (AU) film-forming substances. Edge wetting angle (θ°) and adhesion work (Wa) were used as the criteria for assessing the wettability of titanium dioxide. Three additives were used as SAS: the original product AS-1, obtained from waste of oil refining (with low cost), and industrial additives: "Telaz" and polyethylene polyamine (PEPA). All the studied additives in PPh and AU PVM improve the wetting of titanium dioxide. At the 30 % content of AS film-forming substance in the composition, the maximum decrease in θ° for AS-1 is 4.5°, for PEPA and Telaz it is 4°. For pentaphthalic composition under similar conditions, a decrease in edge wetting angle for AS-1 is 10 °, for Telaz 8.6°, and for PEPA 5.9°. According to the relative change in edge wetting angle for both systems, the maximum decrease in θ° is about 10 %. The introduction of SAS into the composition of AU ambiguously affects the adhesion work, for PPh, the introduction of SAS causes a decrease in adhesion work (Wa). AS-1 is the SAS that minimally reduces adhesion work. The compositions of the PVM by the method of probabilistic-deterministic planning, which ensures maximum wetting of titanium dioxide with film-forming solutions, were analyzed. The equations for calculating the edge angle of wetting of titanium dioxide depending on the content of solvent and the SAS in the PVM were derived. The effectiveness of the AS-1 product as a wetting additive for alkyd paints and varnishes was proven. The wetting ability of the original SAS – AS-1 is close to industrial additives PEPA and Telaz.
- 31 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (6(112)) , 41-50
Open AccessOptimization of titanium dioxide wetting in alkyd paint and varnish materials in the presence of surfactants
This paper reports the results of studying the influence of surfactants (SAS) on the wetting of titanium dioxide in alkyd paint and varnish materials (PVM), based on pentaphthalic (PPh) and alkyd-urethane (AU) film-forming substances. Edge wetting angle (θ°) and adhesion work (Wa) were used as the criteria for assessing the wettability of titanium dioxide. Three additives were used as SAS: the original product AS-1, obtained from waste of oil refining (with low cost), and industrial additives: "Telaz" and polyethylene polyamine (PEPA). All the studied additives in PPh and AU PVM improve the wetting of titanium dioxide. At the 30 % content of AS film-forming substance in the composition, the maximum decrease in θ° for AS-1 is 4.5°, for PEPA and Telaz it is 4°. For pentaphthalic composition under similar conditions, a decrease in edge wetting angle for AS-1 is 10 °, for Telaz 8.6°, and for PEPA 5.9°. According to the relative change in edge wetting angle for both systems, the maximum decrease in θ° is about 10 %. The introduction of SAS into the composition of AU ambiguously affects the adhesion work, for PPh, the introduction of SAS causes a decrease in adhesion work (Wa). AS-1 is the SAS that minimally reduces adhesion work. The compositions of the PVM by the method of probabilistic-deterministic planning, which ensures maximum wetting of titanium dioxide with film-forming solutions, were analyzed. The equations for calculating the edge angle of wetting of titanium dioxide depending on the content of solvent and the SAS in the PVM were derived. The effectiveness of the AS-1 product as a wetting additive for alkyd paints and varnishes was proven. The wetting ability of the original SAS – AS-1 is close to industrial additives PEPA and Telaz.
- 1 January 2019
- Published by Pleiades Publishing Ltd in Glass Physics and Chemistry
- Vol. 45 (1) , 79-81
Effect of Adding Phosphorus-Containing Surfactants on the Properties of Organosilicon Compositions
We report the results of studying the effect of phosphorus-containing compounds, tetraethyl-diamino- tert-butyl phosphite and diethyl phosphite, on organosilicon compositions based on...
- 1 January 2019
- Published by Pleiades Publishing Ltd in Glass Physics and Chemistry
- Vol. 45 (1) , 79-81
Effect of Adding Phosphorus-Containing Surfactants on the Properties of Organosilicon Compositions
We report the results of studying the effect of phosphorus-containing compounds, tetraethyl-diamino- tert-butyl phosphite and diethyl phosphite, on organosilicon compositions based on...
- 1 April 2014
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 87 (4) , 428-433
Bulk and surface properties of lignosulfonic acids and their salts
Results of a study of the influence exerted by the cation composition on the bulk and surface properties of modified lignosulfonates are reported. It was found that the dissolution of lignosulfonic acids is accompanied by dissociation and conformational transitions of macromolecules, which leads to concentration of molecules of lignosulfonic acids in the solution bulk and, as a consequence, to a substantial increase in the surface tension.
- 1 April 2014
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 87 (4) , 428-433
Bulk and surface properties of lignosulfonic acids and their salts
Results of a study of the influence exerted by the cation composition on the bulk and surface properties of modified lignosulfonates are reported. It was found that the dissolution of lignosulfonic acids is accompanied by dissociation and conformational transitions of macromolecules, which leads to concentration of molecules of lignosulfonic acids in the solution bulk and, as a consequence, to a substantial increase in the surface tension.