LCLiangliang Chen

Liangliang Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Liangliang Chen has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Evolution Law and Prediction Model of Anti-Skid and Wear-Resistant Performance of Asphalt Pavement Based on Aggregate Types and Deepened Texture

    by Shaopeng Zheng, Zilong Zhang, Peiwen Hao, Jian Ma, Liangliang Chen

    This study investigates the evolution laws and prediction models of anti-skid and wear-resistant performance for asphalt pavements during the operation period. Using a combination of indoor accelerated wear tests and field detection, mixed specimens are prepared with SBS modified asphalt, limestone, and basalt aggregates. Through accelerated wear tests of different durations, the structural depth and friction coefficient are measured. Combined with the field data from the G56 K2319 section of the Hangrui Expressway, the decay laws of anti-skid performance are analyzed, and prediction models are established. The results show that the anti-skid performance of basalt mixtures is superior to that of limestone. The deepened structure technology significantly enhances the performance of basalt but has a negative impact on the pendulum value of limestone. The influence degrees of wear duration, aggregate type, and deepened structure state on structural depth and pendulum value vary. The initial structural depth of basalt mixtures (0.85 mm) is 11.8% higher than that of limestone (0.76 mm). The longitudinal pendulum value of basalt (44) is 10% higher than that of limestone (40), while the transverse pendulum value of limestone (50) is 4.2% higher than that of basalt (48). After 21 h of wear, the structural depth of basalt (0.68 mm) is 4.6% higher than that of limestone (0.65 mm), with a decay rate 23.6% lower. The pendulum value of basalt remains above 50, while limestone’s longitudinal pendulum value drops to 36 (10% lower than its initial value), even below the unmodified state. The influence order for structural depth is deepened structure state > wear duration > aggregate type, and for lateral pendulum value, it is wear duration > deepened structure state > aggregate type. There is a significant linear relationship between structural depth/pendulum value and wear duration, and the prediction models are reliable. The indoor accelerated wear of 44.5 h is equivalent to the field operation wear of 3 years. The research findings provide a theoretical basis for the evaluation of anti-skid performance, maintenance decision-making, and material optimization of asphalt pavements.


  • Open Access

    Optimized Proportioning Techniques and Roadway Performance Evaluation of Colored Asphalt Pavement Materials

    by Silin Fan, Shaopeng Zheng, Jian Ma, Liangliang Chen, Xiao Li, Cheng Cheng

    This study systematically investigated the formulation optimization, performance evaluation, and practical application of epoxy-based composite materials for colored asphalt pavement. By conducting comprehensive experiments, we optimized the composition of epoxy-based composites, verifying their excellent bonding performance, good heat resistance, and UV aging resistance under various temperature conditions. The key optimized component ratios were determined as a 1:1 blend of Type I and Type II epoxy resins, 30 phr of curing agent, 10 phr of toughening agent, 5 phr of diluent, 10% filler, 12% flame retardant, and 10% pigment. At the recommended dosage of 2.0 kg/m2 of epoxy binder, the composite structure exhibited the best reinforcement effect, improving low-temperature performance significantly. Compared to ordinary asphalt mixtures, the colored pavement composite structure showed superior mechanical strength, deformation capacity, high-temperature stability (dynamic stability approximately three times higher), and water stability (TSR values up to 95.5%). Furthermore, its fatigue life decay rate was significantly lower, with fatigue limit loading frequencies more than three times those of ordinary asphalt mixtures, demonstrating excellent fatigue resistance. This study provides strong technical support and a theoretical basis for the development and practical application of colored asphalt pavement.


  • Open Access

    Analyzing Pore Evolution Characteristics in Cementitious Materials Using a Plane Distribution Model

    by Yezhen Yuan, Zhe He, Kaimin Niu, Bo Tian, Liangliang Chen, Wei Bai, Shaopeng Zheng, Guoman Yu

    This research aims to analyze the distribution and evolution of pores within the planar structure of cement-based materials. Utilizing digital imaging methods, a model for pore plane distribution was established, and the evolutionary patterns of both total pore numbers and varying pore sizes in cement-based materials were investigated. The research introduced an innovative experimental method for analyzing pore distribution within cement-based planar structures. Additionally, a hybrid method was proposed, combining automated image binarization thresholding with manual comparative analysis, thereby enhancing the feasibility of comparative research. Pores were categorized into four distinct sizes: tiny pores (5–200 μm), small pores (200–500 μm), medium pores (500–1000 μm), and large pores (>1000 μm). Areas with apertures <5 μm were classified as dense areas. The findings indicated that the overall number of pores in cement-based materials increased due to the influence of styrene butadiene latex additives. However, at a 15% dosage, the rate of pore formation reached an inflection point, confirming that various factors, such as styrene butadiene latex, air bubbles, and the cement-based material itself, collectively influenced pore formation. The research also demonstrated that styrene butadiene latex affected the four categorized pore sizes differently. Importantly, a higher latex dosage did not necessarily lead to a proportional increase in pore content. Pore content was influenced by multiple factors and exhibited different distribution patterns. The number of micropores, although relatively small, gradually increased with higher latex dosages, while small and medium pores generally showed an upward trend. At a 10% latex dosage, both small and medium pores reached a turning point in their rate of increase. Large pores also exhibited a general increase, peaking at a latex dosage of 10%. It was confirmed that both the total pore volume and the content of micropores were critical factors in determining the mechanical properties of cementitious materials. Higher porosity and micropore content generally weakened mechanical performance. However, at a small latex dosage, there was an improvement in flexural strength. When the latex dosage reached 15%, the total pore and micropore content declined, resulting in a balanced increase in flexural strength and a mitigated decline in compressive strength. This study offers valuable insights into the evolution of total pore volume and the content of pores of various sizes, providing a theoretical basis for the meticulous selection of additive types and dosages from a microscopic perspective.


  • Open Access

    Study on Compaction Properties and Skeleton Structural Characteristics of Porous Asphalt Mixture

    by Zhihao Cheng, Xiao Li, Qilin Yang, Naixing Liang, Liangliang Chen, Shaopeng Zheng, Dawei Wang

    Porous asphalt pavements have a skeletal structure with a large number of interconnecting pores, which can improve drainage, ensure traffic safety, and reduce tire noise. However, it can weaken the mechanical properties of the pavement. One of the key factors affecting the performance of porous asphalt pavements is the quality of compaction, the assessment of which is difficult to accurately quantify. Therefore, Superpave gyratory compaction (SGC) and skeleton penetration tests of porous asphalt mixtures were carried out using three engineering-differentiated gradations in this paper to investigate the gyratory compaction characteristics and the skeleton contact state during penetration. The results show that obvious stages with the increase in number of cycles can be observed during the compaction process. All gradations can achieve the maximum porosity requirements within a reasonable number of compaction cycles, while only the medium and fine gradations can approximately meet the minimum porosity requirements. The coarse gradation takes too long to finish compaction and is almost impossible to meet the minimum porosity. The optimum match between the void ratio of the design gradation and the skeleton contact state can be verified using the VCA ratio and void ratio curves. This is a new method to determine the corresponding target compaction number that can ensure better accuracy and ease of engineering application. Moreover, medium-graded mixtures with better skeletal embedding exhibit greater skeletal strength than coarse-graded aggregates, which provide theoretical support for the establishment of material grade optimization methods.


  • Open Access

    Experiments and Modeling of the Attenuation of the Dynamic Elastic Modulus of Saturated Red Clay under Cyclic Loading

    by Hongyan Ma, Yuanlong Zhuang, Liangliang Chen, Mengxi Lv, Song Xu

    Due to the long-term effect of cyclic traffic loads, the accumulated deformation of red clay subgrades is increasing, strength is decreasing, and problems such as uneven settlement are occurring. In order to improve the stability and durability of red clay subgrade, this paper analyzes the effects of cyclic stress ratios and compactness on the development of the dynamic elastic modulus of saturated red clay. This is achieved through dynamic triaxial tests on red clay in the Qingyuan County, Zhejiang Province, China. The results show that the saturated red clay has an attenuation threshold cyclic stress ratio under cyclic loading. The attenuation threshold cyclic stress ratio prediction models were constructed based on the confining pressure and compactness, respectively. By introducing the concept of a relative cyclic stress ratio, the prediction model of the dynamic elastic modulus of saturated red clay (as based on cyclic vibration times and close cyclic stress ratio) is constructed. The model realizes the prediction of the dynamic elastic modulus of red clay under arbitrary cyclic vibration times via the initial cyclic stress ratio, compactness, and other parameters. It provides a theoretical basis for rationally evaluating the dynamic stability of red clay subgrade under cyclic loading.


  • Open Access

    Experimental Investigation of Cracking and Impact Resistance of Polymer- and Fiber-Enhanced Concrete for Ultra-Thin Whitetopping

    by Liangliang Chen, Shaopeng Zheng, Xiao Li, Zhihao Cheng, Xiaonan Wang

    In order to investigate the effectiveness of polymer modification and fiber reinforcement on the cracking and impact resistance of concrete materials prepared for ultra-thin whitetopping (UTW), carboxyl butyl benzene latex and polyformaldehyde fibers were added to the conventional cement concrete mix. In addition, test methods that used an asphalt mixture performance tester (AMPT) and mechanical rammer were developed to evaluate concrete cracking and impact resistance, respectively. Results from the AMPT test revealed that the cracking resistance can be enhanced with polymer and fiber, especially the initial tensile load peak, which can be improved by more than 40% when fiber and polymer compound modification is applied. Meanwhile, the impact loading test revealed that the inclusion of both fiber and polymer results in a two-fold increase in the number of impacts before visible cracking occurs, and the number of blows to failure increased by 21.4%. Moreover, microstructures were investigated by scanning electron microscopy (SEM) to confirm the reinforcing mechanism of both polymer modification and fiber reinforcement.


  • Open Access

    Microstructure and Key Properties of Phosphogypsum-Red Mud-Slag Composite Cementitious Materials

    by Feiyue Ma, Liangliang Chen, Zhiwei Lin, Zhuo Liu, Weichuan Zhang, Rongxin Guo

    Due to the low content of silicon and aluminum in red mud and the low reaction activity of red mud, when it was used to prepare composite cementitious materials, it was necessary to assist other aluminosilicates and improve their activity by certain methods. In this study, it was proposed to add slag to increase the percentage of silicon and aluminum in the system, and to improve the reactivity of the system through the activation effect of sulfate in phosphogypsum. The effects of slag and phosphogypsum contents on the mechanical properties and microstructures of composite cementitious materials were studied. X-ray diffraction analysis (XRD), thermogravimetric analysis (TG-DTG), and scanning electron microscopy (SEM) were used to analyze the effects of slag and phosphogypsum contents on the hydration products, microstructure, and strength formation mechanism of composite cementitious materials. The results show that with the increase of slag, the strength of the composite cementitious material increases gradually. When the slag content is 50%, the 28-day compressive strength reaches a maximum of about 14 MPa. Compared with the composite material without phosphogypsum, the composite cementitious material with 10–20% phosphogypsum showed higher strength properties, in which the 28-day compressive strength exceeds 24 MPa. The main reason for this is that the sulfate in phosphogypsum can cause the composite cementitious material to generate a large amount of ettringite and accelerate the dissolution of red mud and slag, increasing the release of aluminates, silicates, and Ca2+ to form more C-(A)-S-H and ettringite. In addition, a large amount of C-(A)-S-H makes ettringite and unreacted particles combine into a uniform and compact structure, thus improving the strength. When the content of phosphogypsum exceeds 40%, the 28-day compressive strength of the composite cementitious material drops below 12 MPa due to the presence of fewer hydration products and the expansion of ettringite.


  • Open Access

    Maximum Likelihood Estimation of Parameters for Advanced Continuously Reinforced Concrete Pavement (CRCP) Punchout Calibration Model

    by Liangliang Chen, Feng Zhang, Changjun Zhou

    Pavement performance prediction is the essential part of the pavement design, which is very important for highway agencies for the purpose of budget allocating. This study introduces a model of local calibration for punchout, which is the major structural distress of continuously reinforced concrete pavement (CRCP). It is assumed that the number of equivalent single axle loads’ (ESALs) leads to punchout follows a Weibull distribution. The parameters of Weibull distribution were estimated by maximum likelihood estimation (MLE). Additionally, an approach of estimating the initial value of the parameters was also presented before applying the Newton method for solving the likelihood equations. The regression result was found to fit the performance‐monitoring data from LTPP very well. The proposed calibration model is capable of describing the punchout and can be employed to predict the failure rate and reliability of CRCP in the pavement design and the arrangement of rehabilitation activities.


  • Rheological, mechanical, and abrasion characteristics of polymer-modified cement mortar and concrete

    by Changjun Zhou, Liangliang Chen, Shaopeng Zheng, Yunxi Xu, Decheng Feng

    The settlement of fresh concrete or improper operation during construction usually makes the water to cement (w/c) ratio of the cement mortar on the concrete pavement surface higher than designed, which may influence the abrasion resistance of concrete pavement. This study firstly tried to establish relationships between abrasion of hardened cement mortar and rheological characteristics of fresh cement mortar in the laboratory. Secondly, a polymer-modified cement mortar was developed with carboxyl styrene butadiene rubber latex added to the cement mortar. Its rheological properties in mixing, mechanical properties, and abrasion were investigated. It is found that the polymer-modified cement mortar has a much better abrasion resistance and flexural strength while lower compressive strength than cement mortar. A stronger correlation was observed between flexural strength rather than compressive strength and abrasion resistance of cement mortar. The proposed polymer-modified concrete also exhibited good abrasion resistance.