Włodzimierz Bochniak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Włodzimierz Bochniak has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Paweł Ostachowski
Faculty of Non–Ferrous Metals, AGH University of Krakow, Kraków, Poland
2 shared publications Andrzej Korbel
AGH University of Science and Technology
1 shared publicationKatarzyna Pantoł
Department of Structure and Mechanics of Solids, AGH-University of Science and Technology, al. Mickiewicza 30, 30-059 Kraków, Poland
1 shared publication- Marek Hebda
Faculty of Mechanical Engineering, Cracow University of Technology, Warszawska 24, 31-155 Krakow, Poland
1 shared publication - Martin Duarte Guigou
Department of Engineering and Technology, Catholic University of Uruguay Damaso Antonio Larrañaga, Av. 8 de Octubre 2738, Montevideo 11600, Uruguay
1 shared publication - Piotr Długosz
Centre of Casting Technology, Research Network Lukasiewicz-Krakow Institute of Technology, Zakopiańska 73, 30-418 Kraków, Poland
1 shared publication
Latest Publications
- Open Access
The Influence of Conventional or KOBO Extrusion Process on the Properties of AZ91 (MgAl9Zn1) Alloy
Designers’ efforts to use the lightest possible materials with very good mechanical properties mean that in recent years magnesium alloys have been increasingly used. It is well-known that the use of various plastic working processes allows achieving even better strength properties of the material, often without significant loss of plastic properties in relation to the properties of products obtained in the casting process. The article presents the results of research on microstructural changes and mechanical properties of the alloy AZ91 (MgAl9Zn1) occurring in samples subjected to conventional plastic deformation and the KOBO method. The obtained results were compared to the properties of reference samples, i.e., cast samples. The article presents the advantage of using the low-temperature KOBO method compared to the high-temperature deformation in a conventional manner. Moreover, it has been shown that the use of KOBO extrusion allows the alloy AZ91 (MgAl9Zn1) to obtain superplasticity properties with an elongation of up to 577% compared to the cast reference sample, which is generally classified as difficult for plastic deformation.
Open AccessThe Influence of Conventional or KOBO Extrusion Process on the Properties of AZ91 (MgAl9Zn1) Alloy
Designers’ efforts to use the lightest possible materials with very good mechanical properties mean that in recent years magnesium alloys have been increasingly used. It is well-known that the use of various plastic working processes allows achieving even better strength properties of the material, often without significant loss of plastic properties in relation to the properties of products obtained in the casting process. The article presents the results of research on microstructural changes and mechanical properties of the alloy AZ91 (MgAl9Zn1) occurring in samples subjected to conventional plastic deformation and the KOBO method. The obtained results were compared to the properties of reference samples, i.e., cast samples. The article presents the advantage of using the low-temperature KOBO method compared to the high-temperature deformation in a conventional manner. Moreover, it has been shown that the use of KOBO extrusion allows the alloy AZ91 (MgAl9Zn1) to obtain superplasticity properties with an elongation of up to 577% compared to the cast reference sample, which is generally classified as difficult for plastic deformation.
- 13 June 2016
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 138 (4) , 041002
Plastic Forming of AZ91 Alloy Using the KOBO Method
The desirability of using the KOBO extrusion process for AZ91 magnesium alloy preceding its further plastic processing has been experimentally verified. Importantly, during the conducted experiments, heat treatment (e.g., homogenization) was applied either before or after direct KOBO extrusion, which if used might have affected the properties of the alloy. The products of the cold KOBO process take the form of tapes with different cross sections. They were pressed (deep drawing), or, alternatively, subjected to conventional indirect extrusion in order to acquire the desired spatial geometry of the product. Due to the need for relatively wide strips, a variant of the KOBO extrusion with lateral outflow was used, since the press structure, providing reversibly oscillating die, strongly limited the cross sections of directly extruded products. The research procedure, involving plastic deformation with cyclic changes of the deformation path, allowed to obtain results indicating new potential properties of metallic materials crucial for their applicability.
- 13 June 2016
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 138 (4) , 041002
Plastic Forming of AZ91 Alloy Using the KOBO Method
The desirability of using the KOBO extrusion process for AZ91 magnesium alloy preceding its further plastic processing has been experimentally verified. Importantly, during the conducted experiments, heat treatment (e.g., homogenization) was applied either before or after direct KOBO extrusion, which if used might have affected the properties of the alloy. The products of the cold KOBO process take the form of tapes with different cross sections. They were pressed (deep drawing), or, alternatively, subjected to conventional indirect extrusion in order to acquire the desired spatial geometry of the product. Due to the need for relatively wide strips, a variant of the KOBO extrusion with lateral outflow was used, since the press structure, providing reversibly oscillating die, strongly limited the cross sections of directly extruded products. The research procedure, involving plastic deformation with cyclic changes of the deformation path, allowed to obtain results indicating new potential properties of metallic materials crucial for their applicability.
- 1 February 2013
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 93 (15) , 1883-1913
Lüders deformation and superplastic flow of metals extruded by KOBO method
The work brings the results of the study on mechanical properties of some metallic materials subjected to very large plastic deformation by KOBO extrusion. The unexpected features of the KOBO products like Lüders deformation in pure metals and superplastic flow in coarse grain materials are discussed in terms of micro- and nano-scale elements of their structure. The choice to the experiment materials having different crystallographic and phase structure (commercial purity aluminium, multiphase aluminium 7075 alloy, pure zinc and multiphase magnesium AZ91 alloy) and different history (extrusion, casting) allowed to identify the common nano-size elements of the structure generated during the KOBO deformation which seems to be responsible for the mechanical behaviour of these materials. In particular, clusters of point defects (self-interstitials) formed under the KOBO extrusion conditions (cyclic change in the deformation path, high hydrostatic pressure) were found in these materials regardless of grain size and material early history. They correlate with appearance of unstable Lüders-like or even Portevin–LeChatelier deformation at ambient and superplastic flow at elevated temperatures.
- 1 February 2013
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 93 (15) , 1883-1913
Lüders deformation and superplastic flow of metals extruded by KOBO method
The work brings the results of the study on mechanical properties of some metallic materials subjected to very large plastic deformation by KOBO extrusion. The unexpected features of the KOBO products like Lüders deformation in pure metals and superplastic flow in coarse grain materials are discussed in terms of micro- and nano-scale elements of their structure. The choice to the experiment materials having different crystallographic and phase structure (commercial purity aluminium, multiphase aluminium 7075 alloy, pure zinc and multiphase magnesium AZ91 alloy) and different history (extrusion, casting) allowed to identify the common nano-size elements of the structure generated during the KOBO deformation which seems to be responsible for the mechanical behaviour of these materials. In particular, clusters of point defects (self-interstitials) formed under the KOBO extrusion conditions (cyclic change in the deformation path, high hydrostatic pressure) were found in these materials regardless of grain size and material early history. They correlate with appearance of unstable Lüders-like or even Portevin–LeChatelier deformation at ambient and superplastic flow at elevated temperatures.
- 21 November 2008
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 208 (1-3) , 366-371
Structure of copper subjected to changes of the loading scheme during rolling
- 21 November 2008
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 208 (1-3) , 366-371
Structure of copper subjected to changes of the loading scheme during rolling