Mehdi Balooch
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mehdi Balooch has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Aa Tesar
Lawrence Livermore National Laboratory 1 Livermore, CA94551
1 shared publication- Andres Marquez Rossy
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
1 shared publication - Hsin Wang
Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831, USA
1 shared publication Joseph Simpson
Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
1 shared publicationKenneth Kane
Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
1 shared publication- Kevin G. Field
Department of Nuclear Engineering and Radiological Sciences University of Michigan Ann Arbor Michigan USA
1 shared publication
Latest Publications
- 13 July 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (2) , 025106
Helium implantation in Si (100): Swelling, microstructure, and mechanical property changes
Microstructural changes induced by helium implantation in materials lead to volumetric swelling and mechanical property changes. How these properties are linked and establishing direct relationships can be difficult due to the underlying material’s microstructure evolution. Some materials also experience a phase change due to irradiation damage making them even more complex to analyze. Here, single crystalline Si (100) was used to establish a relationship among these parameters. The swelling height as a function of implantation fluence can equally fit a linear relationship. Solely irradiation induced defects are observed at low fluence below 5.0 × 1016 ions/cm2. An abrupt amorphous and crystalline mixed layer of ∼200 nm thick within a highly damaged polycrystalline matrix is observed when implantation fluence exceeds 5.0 × 1016 ions/cm2, leading to the appearance of irradiation induced swelling and hardening behavior. As the fluence increases beyond 1.0 × 1017 ions/cm2, the amorphous layer expands in size and the bubble size distribution takes the form of a Gaussian distribution with a maximum size of up to 6.4 nm, which causes a further increase in the height of swelling. Furthermore, irradiation induced softening appeared due to the enlarged bubble size and amorphization.
- 13 July 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (2) , 025106
Helium implantation in Si (100): Swelling, microstructure, and mechanical property changes
Microstructural changes induced by helium implantation in materials lead to volumetric swelling and mechanical property changes. How these properties are linked and establishing direct relationships can be difficult due to the underlying material’s microstructure evolution. Some materials also experience a phase change due to irradiation damage making them even more complex to analyze. Here, single crystalline Si (100) was used to establish a relationship among these parameters. The swelling height as a function of implantation fluence can equally fit a linear relationship. Solely irradiation induced defects are observed at low fluence below 5.0 × 1016 ions/cm2. An abrupt amorphous and crystalline mixed layer of ∼200 nm thick within a highly damaged polycrystalline matrix is observed when implantation fluence exceeds 5.0 × 1016 ions/cm2, leading to the appearance of irradiation induced swelling and hardening behavior. As the fluence increases beyond 1.0 × 1017 ions/cm2, the amorphous layer expands in size and the bubble size distribution takes the form of a Gaussian distribution with a maximum size of up to 6.4 nm, which causes a further increase in the height of swelling. Furthermore, irradiation induced softening appeared due to the enlarged bubble size and amorphization.
- Open Access
- 20 September 2019
- Published by Office of Scientific and Technical Information (OSTI)
Handbook of Advanced Manufactured Material Properties From TCR Structure Builds at ORNL (FY2019)
The U.S. Department of Energy's Office of Scientific and Technical Information
- 20 September 2019
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessHandbook of Advanced Manufactured Material Properties From TCR Structure Builds at ORNL (FY2019)
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 January 1991
- Published by ASTM International
- p. 228-236
Morphology and Laser Damage Studies by Atomic Force Microscopy of E-Beam Evaporation Deposited AR and HR Coatings
Atomic Force Microscopy is a powerful tool for exploring the surface morphology of dielectric thin film coatings. We have demonstrated the utility of this tool in monitoring processing defects, laser conditioning and aging, and laser damage in e-beam evaporation deposited AR and HR coatings with a resolution not previously available.
- 1 January 1991
- Published by ASTM International
- p. 228-236
Morphology and Laser Damage Studies by Atomic Force Microscopy of E-Beam Evaporation Deposited AR and HR Coatings
Atomic Force Microscopy is a powerful tool for exploring the surface morphology of dielectric thin film coatings. We have demonstrated the utility of this tool in monitoring processing defects, laser conditioning and aging, and laser damage in e-beam evaporation deposited AR and HR coatings with a resolution not previously available.