Abdalla Mostafa Elmarhomy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Abdalla Mostafa Elmarhomy has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Abd El-Aziz Morgan
Mechanical Power Engineer Department, Faculty of Engineering, Ain Shams University in Egypt, Cairo 11517, Egypt
1 shared publication - Ahmed M. Shawqran
Department of Engineering Physics and Mathematics, Faculty of Engineering, Ain Shams University, Cairo 11566, Egypt
1 shared publication - Ahmed Mohamed Reda Elbaz
The British University in Egypt
1 shared publication - Alaa Ismail
Engineering Physics and Mathematics Department., Faculty of Engineering, Ain Shams University in Egypt, Cairo 11517, Egypt
1 shared publication - Ali Shehab
Ain Shams University
1 shared publication - Ashraf Mostafa Hamed
Mechanical Power Engineering Department, Faculty of Engineering, Ain Shams University, Cairo, Egypt
1 shared publication
Latest Publications
- Open Access
- 19 June 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 106 (1) , 147-157
Numerical Modeling and Geometry Enhancement of a Reactive Silencer
Internal combustion engines and blowers frequently utilize silencers to reduce exhaust noise. In the current paper, the transmission loss of reactive silencers is predicted using the plane wave decomposition method and a three-dimensional (3-D) time-domain computational fluid dynamics (CFD) approach. A mass-flow-inlet boundary condition is first used to perform a steady flow computation, which serves as an initial condition for the two subsequent unsteady flow computations. At the model's inlet, an impulse (acoustic excitation) is placed over the constant mass flow to perform the first unstable flow computation. Once the impulse has fully propagated into the silencer, the non-reflecting boundary condition (NRBC) is then added. For the scenario without acoustic excitation at the inlet, a second unsteady flow computation is performed. During the two transient computations, the time histories of the pressure and velocity at the upstream measuring points as well as the history of the pressures at the downstream measuring point are recorded. The related acoustic quantities show variations between the two unsteady flow computational findings. As a result, the transmitted sound pressure signal is just the sound pressure downstream, while the incident sound pressure signal is obtained by utilizing plane wave decomposition upstream. The transmission loss (TL) of the silencer is then calculated after the Fast Fourier Transform (FFT) converts the two sound pressure signals from the time domain to the frequency domain. The numerical calculations and the reported data are in good agreement for the published results, in addition to geometry enhancement by increasing number of holes in the cross section for muffler.
- 19 June 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 106 (1) , 147-157
Open AccessNumerical Modeling and Geometry Enhancement of a Reactive Silencer
Internal combustion engines and blowers frequently utilize silencers to reduce exhaust noise. In the current paper, the transmission loss of reactive silencers is predicted using the plane wave decomposition method and a three-dimensional (3-D) time-domain computational fluid dynamics (CFD) approach. A mass-flow-inlet boundary condition is first used to perform a steady flow computation, which serves as an initial condition for the two subsequent unsteady flow computations. At the model's inlet, an impulse (acoustic excitation) is placed over the constant mass flow to perform the first unstable flow computation. Once the impulse has fully propagated into the silencer, the non-reflecting boundary condition (NRBC) is then added. For the scenario without acoustic excitation at the inlet, a second unsteady flow computation is performed. During the two transient computations, the time histories of the pressure and velocity at the upstream measuring points as well as the history of the pressures at the downstream measuring point are recorded. The related acoustic quantities show variations between the two unsteady flow computational findings. As a result, the transmitted sound pressure signal is just the sound pressure downstream, while the incident sound pressure signal is obtained by utilizing plane wave decomposition upstream. The transmission loss (TL) of the silencer is then calculated after the Fast Fourier Transform (FFT) converts the two sound pressure signals from the time domain to the frequency domain. The numerical calculations and the reported data are in good agreement for the published results, in addition to geometry enhancement by increasing number of holes in the cross section for muffler.
- 30 May 2023
- Published by Springer Nature
- p. 159-182
Hydrodynamic Analysis and CFD Modeling of PAWEC Interacted with Regular Waves Using CFX
- 30 May 2023
- Published by Springer Nature
- p. 159-182
Hydrodynamic Analysis and CFD Modeling of PAWEC Interacted with Regular Waves Using CFX
- Open Access
Reduction of Total Harmonic Distortion of Wind Turbine Active Power Using Blade Angle Adaptive PI Controller
Power quality can have a large detrimental effect on industrial processes and the commercial sector. Thus, this paper proposes a new technique to improve the power quality of electric power systems. This technique relies on auto-adjusting of the blade angle to mitigate the harmonics in wind generator active power. A new adaptive PI blade-angle controller is applied in this technique to reduce the total harmonic distortion (THD) of the output power. The parameters of the adaptive PI controller are initialized by using the Harmony Search algorithm (HSA), hybrid Harmony Search optimization and Equilibrium optimization (EO), and hybrid Harmony Search optimization and Teaching learning-based optimization (TLBO). The execution of the optimization algorithms relies mainly on the optimization objective function. Two optimization objective functions are mathematically modeled and compared to enhance the power quality. The first one is to minimize the sum square of error, while the second objective is to minimize the THD. Many case studies are applied with various wind-speed profiles under normal and faulty conditions. Results show the superiority of HSA hybrid EO algorithm with the second objective functions through reducing the harmonics and enhancing the power quality. Moreover, laboratory studies are applied to investigate the effect of the blade-angle variations on the extracted active power.
Open AccessReduction of Total Harmonic Distortion of Wind Turbine Active Power Using Blade Angle Adaptive PI Controller
Power quality can have a large detrimental effect on industrial processes and the commercial sector. Thus, this paper proposes a new technique to improve the power quality of electric power systems. This technique relies on auto-adjusting of the blade angle to mitigate the harmonics in wind generator active power. A new adaptive PI blade-angle controller is applied in this technique to reduce the total harmonic distortion (THD) of the output power. The parameters of the adaptive PI controller are initialized by using the Harmony Search algorithm (HSA), hybrid Harmony Search optimization and Equilibrium optimization (EO), and hybrid Harmony Search optimization and Teaching learning-based optimization (TLBO). The execution of the optimization algorithms relies mainly on the optimization objective function. Two optimization objective functions are mathematically modeled and compared to enhance the power quality. The first one is to minimize the sum square of error, while the second objective is to minimize the THD. Many case studies are applied with various wind-speed profiles under normal and faulty conditions. Results show the superiority of HSA hybrid EO algorithm with the second objective functions through reducing the harmonics and enhancing the power quality. Moreover, laboratory studies are applied to investigate the effect of the blade-angle variations on the extracted active power.