Zain Maqsood
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zain Maqsood has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Badee Alshameri
National University of Sciences and Technology, Islamabad, Pakistan
4 shared publications Jiren Xie
2 shared publications- Jiren Xie
Department of Civil Engineering, Central South University, Changsha, China
2 shared publications - Junichi Koseki
Department of Civil Engineering, The University of Tokyo
2 shared publications Lin Wenli
2 shared publicationsLiu Ang
2 shared publications
Latest Publications
- Open Access
Experimental Evaluation and Prediction of the Dynamic Modulus of Crumb Rubber-Modified Stone Mastic Asphalt Mixtures
Increased and excessive axle loads (exceeding design specifications) at high temperatures stimulate premature distresses in flexible pavements. This study utilizes the novelty of engineered bituminous composite—crumb rubber-modified (CRM) stone mastic asphalt (SMA) for pavement longevity and sustainable performance. Dynamic modulus testing was employed at four temperatures and six frequency sweeps. The experimental design included the preparation of SMA 19 specimens with six different percentages of crumb rubber (CR) mixed in bitumen. CR addition to the mix translated into an improved stiffness of the mix, as a 64% increase in dynamic modulus (on average) was reported at 10% CR as compared to a neat mixture. Master curves were produced using |E*| test results, which revealed that 10% modified SMA was relatively stiffer and more rut-resistant than the other mixtures. Performance prediction models were developed for |E*| using artificial neural networks (ANNs) and non-linear regression, wherein the former proved to be more robust. Sensitivity analysis revealed that a temperature rise (21.1 to 37.8 °C) translated into a 65% drop in |E*| (on average) and a rise in frequency (0.1 to 25 Hz) divulged a 72% upsurge in |E*| (on average). This research demonstrates the promise of deploying CR SMA mixtures, particularly for high-traffic and heavy-load scenarios.
Open AccessExperimental Evaluation and Prediction of the Dynamic Modulus of Crumb Rubber-Modified Stone Mastic Asphalt Mixtures
Increased and excessive axle loads (exceeding design specifications) at high temperatures stimulate premature distresses in flexible pavements. This study utilizes the novelty of engineered bituminous composite—crumb rubber-modified (CRM) stone mastic asphalt (SMA) for pavement longevity and sustainable performance. Dynamic modulus testing was employed at four temperatures and six frequency sweeps. The experimental design included the preparation of SMA 19 specimens with six different percentages of crumb rubber (CR) mixed in bitumen. CR addition to the mix translated into an improved stiffness of the mix, as a 64% increase in dynamic modulus (on average) was reported at 10% CR as compared to a neat mixture. Master curves were produced using |E*| test results, which revealed that 10% modified SMA was relatively stiffer and more rut-resistant than the other mixtures. Performance prediction models were developed for |E*| using artificial neural networks (ANNs) and non-linear regression, wherein the former proved to be more robust. Sensitivity analysis revealed that a temperature rise (21.1 to 37.8 °C) translated into a 65% drop in |E*| (on average) and a rise in frequency (0.1 to 25 Hz) divulged a 72% upsurge in |E*| (on average). This research demonstrates the promise of deploying CR SMA mixtures, particularly for high-traffic and heavy-load scenarios.
- 10 November 2025
- Published by Springer Nature in Acta Geotechnica
- Vol. 21 (3) , 1729-1748
Acoustic emission characterization of mechanical behavior during pile penetration in dry calcareous sands
- 10 November 2025
- Published by Springer Nature in Acta Geotechnica
- Vol. 21 (3) , 1729-1748
Acoustic emission characterization of mechanical behavior during pile penetration in dry calcareous sands
- Open Access
- 12 August 2025
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 16 (1) , 1-34
Data-driven approach to enhance deep foundation safety: reliable methods for predicting bored pile capacity
The interpretation methods used to predict ultimate pile capacity from load-settlement curves yield varied results due to their unique assumptions and limitations. Misinterpreting ultimate pile capacity can negatively impact the safety and economy of deep foundations, which often consist of numerous piles. This study examines a database of 93 static pile load tests on axially loaded bored concrete piles to identify suitable methods for predicting ultimate pile capacity. Specifically, 43 static pile load tests from Pile Database A were analyzed to compare ultimate capacities derived from theoretical methods, twelve pile load test interpretation techniques, and numerical analysis using PLAXIS 3D. For the numerical analysis, all bored piles in Database A were loaded until a pile head settlement equal to 8% of the pile diameter, which is the average failure settlement percentage derived from 50 full-scale static pile load tests (Database-B). The results indicate that the interpretation methods of DeBeer and Mazurkiewicz provide results closest to the maximum test load in static pile load tests, with an average deviation of 4.16% from the maximum applied test load. Therefore, these methods are reliable for predicting the ultimate capacity of bored piles. The findings of this study are expected to help design professionals adopt suitable and reliable methods for accurately assessing the ultimate capacity of bored piles.
- 12 August 2025
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 16 (1) , 1-34
Open AccessData-driven approach to enhance deep foundation safety: reliable methods for predicting bored pile capacity
The interpretation methods used to predict ultimate pile capacity from load-settlement curves yield varied results due to their unique assumptions and limitations. Misinterpreting ultimate pile capacity can negatively impact the safety and economy of deep foundations, which often consist of numerous piles. This study examines a database of 93 static pile load tests on axially loaded bored concrete piles to identify suitable methods for predicting ultimate pile capacity. Specifically, 43 static pile load tests from Pile Database A were analyzed to compare ultimate capacities derived from theoretical methods, twelve pile load test interpretation techniques, and numerical analysis using PLAXIS 3D. For the numerical analysis, all bored piles in Database A were loaded until a pile head settlement equal to 8% of the pile diameter, which is the average failure settlement percentage derived from 50 full-scale static pile load tests (Database-B). The results indicate that the interpretation methods of DeBeer and Mazurkiewicz provide results closest to the maximum test load in static pile load tests, with an average deviation of 4.16% from the maximum applied test load. Therefore, these methods are reliable for predicting the ultimate capacity of bored piles. The findings of this study are expected to help design professionals adopt suitable and reliable methods for accurately assessing the ultimate capacity of bored piles.
- 3 August 2024
- Published by Springer Nature in Multiscale and Multidisciplinary Modeling, Experiments and Design
- Vol. 7 (6) , 5809-5827
Predictive modeling of Atterberg's limits of soil passing through sieve #40 and #200 using artificial neural networks and multivariate regression: advancing sustainable construction practices
- 3 August 2024
- Published by Springer Nature in Multiscale and Multidisciplinary Modeling, Experiments and Design
- Vol. 7 (6) , 5809-5827
Predictive modeling of Atterberg's limits of soil passing through sieve #40 and #200 using artificial neural networks and multivariate regression: advancing sustainable construction practices
- 1 February 2024
- Published by Emerald Publishing in Geosynthetics International
- Vol. 31 (1) , 18-30
Mechanical behaviour and stress-strain recovery characteristics of expanded polypropylene
Expanded polypropylene (EPP) foam has been widely recognized as an energy absorbing material, and it is routinely used for variety of industrial applications. However, EPP foam has a relatively limited scope in the construction industry, especially for load-bearing applications. To address this aspect, the mechanical behaviour of EPP foam was examined under unconfined conditions in this study, and the effects of different preloading/precompression strain histories (5% to 60%) on the stress-strain response and strain energy characteristics of EPP were evaluated. Additionally, the stress-strain recovery behaviour of EPP foam having different preloading histories was also studied while considering the effects of recovery time after preloading (0 to 28 Days). The results suggest that EPP foam subjected to different preloading histories has identical patterns of stress-strain response to other conventional closed-cell polymeric foams, such as expanded polystyrene (EPS) foam, and EPP can adequately be used for load-bearing applications under the recommended design limits. Furthermore, noticeable recovery in the stress-strain response of EPP was also witnessed during the initial 14 days after preloading. Based on these findings, it is anticipated that the promising stress-strain recovery characteristics of EPP foam enable it to be reused, even after experiencing large in situ deformations.
- 1 February 2024
- Published by Emerald Publishing in Geosynthetics International
- Vol. 31 (1) , 18-30
Mechanical behaviour and stress-strain recovery characteristics of expanded polypropylene
Expanded polypropylene (EPP) foam has been widely recognized as an energy absorbing material, and it is routinely used for variety of industrial applications. However, EPP foam has a relatively limited scope in the construction industry, especially for load-bearing applications. To address this aspect, the mechanical behaviour of EPP foam was examined under unconfined conditions in this study, and the effects of different preloading/precompression strain histories (5% to 60%) on the stress-strain response and strain energy characteristics of EPP were evaluated. Additionally, the stress-strain recovery behaviour of EPP foam having different preloading histories was also studied while considering the effects of recovery time after preloading (0 to 28 Days). The results suggest that EPP foam subjected to different preloading histories has identical patterns of stress-strain response to other conventional closed-cell polymeric foams, such as expanded polystyrene (EPS) foam, and EPP can adequately be used for load-bearing applications under the recommended design limits. Furthermore, noticeable recovery in the stress-strain response of EPP was also witnessed during the initial 14 days after preloading. Based on these findings, it is anticipated that the promising stress-strain recovery characteristics of EPP foam enable it to be reused, even after experiencing large in situ deformations.
- Open Access
- 2 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1603
Verification of 3D AE Source Location Technique in Triaxial Compression Tests Using Pencil Lead Break Sources on a Cylindrical Metal Specimen
Recently, the acoustic emission (AE) technique has been widely applied in the field of geotechnical engineering. One of the main applications of this technique is to locate damage sources, which is known as the AE source location technique. In this research, the 3D AE source location technique based on the time difference of arrival is verified by conducting pencil lead break (PLB) tests on a cylindrical metal specimen. From the results of this study, the existing method is proven to have the least error in terms of distance from the coordinate origin, but with some errors along x, y, and z axes. When the PLB sources originate in the middle part of the specimen, the calculated result has a higher accuracy, as compared to other positions. It seems that the calculated AE sources tend to be concentrated on the central part with some errors. Moreover, outside noises induced by a hammer hit have virtually no effect on this AE source location technique.
- 2 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1603
Open AccessVerification of 3D AE Source Location Technique in Triaxial Compression Tests Using Pencil Lead Break Sources on a Cylindrical Metal Specimen
Recently, the acoustic emission (AE) technique has been widely applied in the field of geotechnical engineering. One of the main applications of this technique is to locate damage sources, which is known as the AE source location technique. In this research, the 3D AE source location technique based on the time difference of arrival is verified by conducting pencil lead break (PLB) tests on a cylindrical metal specimen. From the results of this study, the existing method is proven to have the least error in terms of distance from the coordinate origin, but with some errors along x, y, and z axes. When the PLB sources originate in the middle part of the specimen, the calculated result has a higher accuracy, as compared to other positions. It seems that the calculated AE sources tend to be concentrated on the central part with some errors. Moreover, outside noises induced by a hammer hit have virtually no effect on this AE source location technique.
- Open Access
Experimental Study on the Relationship between the Velocity of Surface Movements and Tilting Rate in Pre-Failure Stage of Rainfall-Induced Landslides
With the development of deformation measuring technology at slope surfaces, prediction methods for rainfall-induced landslides based on the surface movements and tilting of slopes in the pre-failure stage have been recognized as a promising technique for risk reduction of slope failure triggered by rainfall. However, the correlation and possible mechanism for these prediction methods were rarely discussed. In this study, the comparison between the prediction methods of slope failure based on the time history of surface displacements and tilting in the acceleration stage was carried out by conducting a series of laboratory tests and field tests under rainfall, in which the movements and tilting behaviors at the slope surface were measured. The results show that the predicted failure time of tested slopes obtained by different prediction methods is consistent, and the correlation between these landslide prediction methods were also detected. A proportional relationship between the velocity of surface displacements and tilting rate was observed, and a possible mechanism for the sliding behavior was discussed based on this linear relationship as well. In addition, an expression for the linear relationship between the rate of the surface tilting and displacement was also established in this study, and the results could have significance for the understanding of the sliding behavior in the failure process in rainfall-induced landslides.
Open AccessExperimental Study on the Relationship between the Velocity of Surface Movements and Tilting Rate in Pre-Failure Stage of Rainfall-Induced Landslides
With the development of deformation measuring technology at slope surfaces, prediction methods for rainfall-induced landslides based on the surface movements and tilting of slopes in the pre-failure stage have been recognized as a promising technique for risk reduction of slope failure triggered by rainfall. However, the correlation and possible mechanism for these prediction methods were rarely discussed. In this study, the comparison between the prediction methods of slope failure based on the time history of surface displacements and tilting in the acceleration stage was carried out by conducting a series of laboratory tests and field tests under rainfall, in which the movements and tilting behaviors at the slope surface were measured. The results show that the predicted failure time of tested slopes obtained by different prediction methods is consistent, and the correlation between these landslide prediction methods were also detected. A proportional relationship between the velocity of surface displacements and tilting rate was observed, and a possible mechanism for the sliding behavior was discussed based on this linear relationship as well. In addition, an expression for the linear relationship between the rate of the surface tilting and displacement was also established in this study, and the results could have significance for the understanding of the sliding behavior in the failure process in rainfall-induced landslides.