Gokilakrishnan Gopal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gokilakrishnan Gopal has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
B. N. Sreeharan
Department of Mechanical Engineering, Kumaraguru College of Technology, Coimbatore, India
2 shared publicationsC. Nithiyapathi
Department of Mechanical Engineering, Karpagam Academy of Higher Education, Coimbatore, India
2 shared publicationsC. Rajendran
Dean R&D and Innovation, Sri Krishna College of Engineering and Technology, Coimbatore, India
2 shared publicationsG. Mahendran
Centre for Vibration Testing and Analysis, Department of Mechanical Engineering, Chennai Institute of Technology, Chennai-600069, Tamil Nadu, India
2 shared publicationsN. Kavitha
Department of Science and Humanities, Sri Eshwar College of Engineering, Coimbatore, India
2 shared publicationsP. Ashoka Varthanan
Dean R&D and Innovation, Sri Krishna College of Engineering and Technology, Coimbatore, India
2 shared publications
Latest Publications
- 29 September 2026
- Published by Springer Nature in Polymer Bulletin
- Vol. 83 (12) , 657
Mechanical, wear, flammability, and thermal conductivity behaviour of epoxy composites reinforced with bottle gourd stem cellulose and chopped grape stem fibers
- 29 September 2026
- Published by Springer Nature in Polymer Bulletin
- Vol. 83 (12) , 657
Mechanical, wear, flammability, and thermal conductivity behaviour of epoxy composites reinforced with bottle gourd stem cellulose and chopped grape stem fibers
- Open Access
- 1 August 2025
- Published by CSIR-National Institute of Science Communication and Policy Research (NIScPR) in Journal of Scientific & Industrial Research
- Vol. 84 (8) , 890-900
Analysis of Barriers to Implement Lean Manufacturing Principles and Industry 4.0 Technologies Concurrently in Indian Manufacturing Organizations
Industries all over the world are practicing Lean Manufacturing (LM) techniques during the last twenty years and have significantly reduced the wastes from the shop floor level to enterprise level activities. On the other hand, the industrial settings are elevated to the next level with the help of Industry 4.0 technologies. Despite this transition, Small and Medium Enterprises (SMEs) face challenges like technological constraints, financial limitations and regulatory complexities. To address this issue, the present study aims to analyse the barriers for implementing LM and Industry 4.0 concurrently in SMEs across process, product and service industries in the southern part of India. In addition, the driving forces and strategies were also analysed to understand the perception towards LM and Industry 4.0. A questionnaire-based survey methodology is adapted to carry out the research. The survey method is intended to highlight the barriers faced by Indian SMEs while implementing LM and Industry 4.0 technologies. Though 43% of the surveyed SMEs already started practicing LM and Industry 4.0 techniques, remaining still requires directions to adapt these techniques. A novel approach adapting hypothesis testing and Principal Component Analysis (PCA) was used to prioritize the identified barriers. Analysis on the survey results show that the majority of the barriers are related to standards, knowledge and awareness on LM and Industry 4.0. The results provide an overview of Indian SMEs’ present status on LM and Industry 4.0 adaption, and important aspects to be focused by the organizations’ management and academicians for the successful implementation.
- 1 August 2025
- Published by CSIR-National Institute of Science Communication and Policy Research (NIScPR) in Journal of Scientific & Industrial Research
- Vol. 84 (8) , 890-900
Open AccessAnalysis of Barriers to Implement Lean Manufacturing Principles and Industry 4.0 Technologies Concurrently in Indian Manufacturing Organizations
Industries all over the world are practicing Lean Manufacturing (LM) techniques during the last twenty years and have significantly reduced the wastes from the shop floor level to enterprise level activities. On the other hand, the industrial settings are elevated to the next level with the help of Industry 4.0 technologies. Despite this transition, Small and Medium Enterprises (SMEs) face challenges like technological constraints, financial limitations and regulatory complexities. To address this issue, the present study aims to analyse the barriers for implementing LM and Industry 4.0 concurrently in SMEs across process, product and service industries in the southern part of India. In addition, the driving forces and strategies were also analysed to understand the perception towards LM and Industry 4.0. A questionnaire-based survey methodology is adapted to carry out the research. The survey method is intended to highlight the barriers faced by Indian SMEs while implementing LM and Industry 4.0 technologies. Though 43% of the surveyed SMEs already started practicing LM and Industry 4.0 techniques, remaining still requires directions to adapt these techniques. A novel approach adapting hypothesis testing and Principal Component Analysis (PCA) was used to prioritize the identified barriers. Analysis on the survey results show that the majority of the barriers are related to standards, knowledge and awareness on LM and Industry 4.0. The results provide an overview of Indian SMEs’ present status on LM and Industry 4.0 adaption, and important aspects to be focused by the organizations’ management and academicians for the successful implementation.
- 21 May 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 33 (13)
CHARACTERIZATION OF AMINO-SILANE FUNCTIONALIZED ANNEALED BIOSILICA AND NETTLE FIBER-REINFORCED VINYL ESTER COMPOSITE
In this research study, the characterization of vinyl-based composites reinforced with annealed-amino silane functionalized fox tail millet husk biosilica and nettle fiber is performed. The primary objective of this study is to analyze how the annealed aminosilane-treated fox tail millet husk biosilica performed as a functional filler in a nettle fiber-reinforced vinyl ester resin composite. The vinyl resin was selected for its small shrinkage after curing, and the biosilica was obtained by an alkaline and acid treatment method. The extracted biosilica was subjected to annealing at [Formula: see text]C to enhance its microstructural properties and subsequently treated with an amino silane coupling agent to improve its compatibility with the resin matrix. The composites were produced by integrating vinyl ester resin, 30[Formula: see text]vol.% nettle fiber, and different quantities of biosilica, subsequently undergoing curing and post-curing procedures. Among the evaluated specimens VNB4 exhibited exceptional mechanical properties. Similarly, composite VNB6 demonstrated an optimal wear resistance, characterized by a specific wear rate of 0.00081[Formula: see text]mm 3 /Nm and a coefficient of friction (COF) of 0.085, resulting from enhanced matrix reinforcement and reduced friction. Moreover, composite VNB6 demonstrates the greatest thermal stability, achieving a TG% of 99 at [Formula: see text]C. Scanning electron microscopy (SEM) examination validated these findings by demonstrating well-dispersed biosilica particles and enhanced fiber-matrix adhesion. Finally, the research proves that the meticulous regulation of the treatment and incorporation of biosilica and nettle fiber substantially enhanced the load-bearing properties of composite with promising engineering applications.
- 21 May 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 33 (13)
CHARACTERIZATION OF AMINO-SILANE FUNCTIONALIZED ANNEALED BIOSILICA AND NETTLE FIBER-REINFORCED VINYL ESTER COMPOSITE
In this research study, the characterization of vinyl-based composites reinforced with annealed-amino silane functionalized fox tail millet husk biosilica and nettle fiber is performed. The primary objective of this study is to analyze how the annealed aminosilane-treated fox tail millet husk biosilica performed as a functional filler in a nettle fiber-reinforced vinyl ester resin composite. The vinyl resin was selected for its small shrinkage after curing, and the biosilica was obtained by an alkaline and acid treatment method. The extracted biosilica was subjected to annealing at [Formula: see text]C to enhance its microstructural properties and subsequently treated with an amino silane coupling agent to improve its compatibility with the resin matrix. The composites were produced by integrating vinyl ester resin, 30[Formula: see text]vol.% nettle fiber, and different quantities of biosilica, subsequently undergoing curing and post-curing procedures. Among the evaluated specimens VNB4 exhibited exceptional mechanical properties. Similarly, composite VNB6 demonstrated an optimal wear resistance, characterized by a specific wear rate of 0.00081[Formula: see text]mm 3 /Nm and a coefficient of friction (COF) of 0.085, resulting from enhanced matrix reinforcement and reduced friction. Moreover, composite VNB6 demonstrates the greatest thermal stability, achieving a TG% of 99 at [Formula: see text]C. Scanning electron microscopy (SEM) examination validated these findings by demonstrating well-dispersed biosilica particles and enhanced fiber-matrix adhesion. Finally, the research proves that the meticulous regulation of the treatment and incorporation of biosilica and nettle fiber substantially enhanced the load-bearing properties of composite with promising engineering applications.
- Open Access
- 16 August 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 19 (5) , 3867
Correction: Simulation based swarm intelligence optimization to develop manufacturing distribution plan
- 16 August 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 19 (5) , 3867
Open AccessCorrection: Simulation based swarm intelligence optimization to develop manufacturing distribution plan
- 8 July 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 19 (5) , 3855-3865
Simulation based swarm intelligence optimization to develop manufacturing distribution plan
- 8 July 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 19 (5) , 3855-3865
Simulation based swarm intelligence optimization to develop manufacturing distribution plan
- 17 February 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (4) , 5911-5924
Characterization of heat-treated biosilica from biomass waste fox tail millet husks and banana fiber reinforced epoxy composite
- 17 February 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (4) , 5911-5924
Characterization of heat-treated biosilica from biomass waste fox tail millet husks and banana fiber reinforced epoxy composite
- 10 February 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (1) , 1433-1442
Mechanical, wear, and flammability of chitin-rich endoskeleton of Sepioteuthis Sepioidea powder-dispersed pineapple fiber-reinforced polyester composite
- 10 February 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (1) , 1433-1442
Mechanical, wear, and flammability of chitin-rich endoskeleton of Sepioteuthis Sepioidea powder-dispersed pineapple fiber-reinforced polyester composite
- 23 May 2023
- Published by Springer Nature in International Journal of System Assurance Engineering and Management
- Vol. 14 (4) , 1208-1217
Implementation of lean six sigma (LSS) techniques for tyre manufacturing in small and medium-sized enterprises
- 23 May 2023
- Published by Springer Nature in International Journal of System Assurance Engineering and Management
- Vol. 14 (4) , 1208-1217
Implementation of lean six sigma (LSS) techniques for tyre manufacturing in small and medium-sized enterprises