Osman Perçi̇n
Research Subjects
Osman Perçi̇n has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Bilal Dogan
Institute of Graduate Education, Kutahya Dumlupinar University, Kutahya, Turkey
2 shared publications - Mustafa Altunok
Gazi Üniversitesi
2 shared publications - Ercan Çi̇ğDem
Kutahya Dumlupinar Universitesi
1 shared publication - Mehmet Sarıkahya
Afyon Kocatepe Universitesi
1 shared publication - Musa Atar
Gazi Üniversitesi
1 shared publication Mustafa Altunok
1 shared publication
Latest Publications
- 16 December 2025
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 8 (2) , 358-372
Emprenye ve ısıl işlemin karaçam (Pinus nigra) ağacının fiziksel ve mekanik özellikleri üzerine etkileri
Bu çalışmada, bor bileşikleri ile emprenye işleminden sonra farklı sıcaklıklarda uygulanan ısıl işlemin ahşap malzemenin fiziksel ve mekanik özellikleri üzerindeki etkisi incelenmiştir. Bu amaçla, deney örnekleri %1, %3 ve %5 konsantrasyonlarında boraks (Bx) ve borik asit (Ba) çözeltileriyle 48 saat daldırma yöntemiyle emprenye edilmiş ve ardından 150°C, 170°C, 190°C ve 210°C'de üç saat ısıl işlem uygulanmıştır. Deney örneklerinin hava kurusu yoğunluk, liflere paralel basınç direnci (BD) ve eğilme direnci (ED) değerleri belirlenmiştir. Araştırma sonuçları, ısıl işlem uygulanmış deney örneklerinde yoğunluk değerlerinin, artan ısıl işlem sıcaklığıyla azaldığını göstermiştir. Öte yandan, bor bileşikleri ısıl işlem uygulanmamış deney örneklerinin yoğunluk değerlerini artırmıştır. Bor bileşikleri ile emprenye işlemi ve ısıl işlem uygulaması deney örneklerinin BD özelliklerinde hafif bir artışa neden olmuştur. Ayrıca, emprenye edilmiş ve ısıl işlem uygulanmış deney örneklerinin ED değerleri, düşük sıcaklıklarda arttığı, yüksek sıcaklıklarda ise azaldığı tespit edilmiştir. Isıl işlem sırasında ED ve BD özelliklerinde görülen azalmaların, ısıl işlemden önce bor bileşikleri ile emprenye edilmesiyle hafifletildiği ve Bx ve Ba emprenye çözeltilerinin sırasıyla BD ve ED özellikleri üzerinde daha olumlu etkilere sahip olduğu belirlenmiştir.
- 16 December 2025
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 8 (2) , 358-372
Emprenye ve ısıl işlemin karaçam (Pinus nigra) ağacının fiziksel ve mekanik özellikleri üzerine etkileri
Bu çalışmada, bor bileşikleri ile emprenye işleminden sonra farklı sıcaklıklarda uygulanan ısıl işlemin ahşap malzemenin fiziksel ve mekanik özellikleri üzerindeki etkisi incelenmiştir. Bu amaçla, deney örnekleri %1, %3 ve %5 konsantrasyonlarında boraks (Bx) ve borik asit (Ba) çözeltileriyle 48 saat daldırma yöntemiyle emprenye edilmiş ve ardından 150°C, 170°C, 190°C ve 210°C'de üç saat ısıl işlem uygulanmıştır. Deney örneklerinin hava kurusu yoğunluk, liflere paralel basınç direnci (BD) ve eğilme direnci (ED) değerleri belirlenmiştir. Araştırma sonuçları, ısıl işlem uygulanmış deney örneklerinde yoğunluk değerlerinin, artan ısıl işlem sıcaklığıyla azaldığını göstermiştir. Öte yandan, bor bileşikleri ısıl işlem uygulanmamış deney örneklerinin yoğunluk değerlerini artırmıştır. Bor bileşikleri ile emprenye işlemi ve ısıl işlem uygulaması deney örneklerinin BD özelliklerinde hafif bir artışa neden olmuştur. Ayrıca, emprenye edilmiş ve ısıl işlem uygulanmış deney örneklerinin ED değerleri, düşük sıcaklıklarda arttığı, yüksek sıcaklıklarda ise azaldığı tespit edilmiştir. Isıl işlem sırasında ED ve BD özelliklerinde görülen azalmaların, ısıl işlemden önce bor bileşikleri ile emprenye edilmesiyle hafifletildiği ve Bx ve Ba emprenye çözeltilerinin sırasıyla BD ve ED özellikleri üzerinde daha olumlu etkilere sahip olduğu belirlenmiştir.
- Open Access
- 30 June 2025
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 8 (1) , 156-171
Performance properties of heat treated and reinforced laminated veneer lumber with glass fiber
In this study, some technological properties of test samples manufactured from heat-treated scotch pine (Pinus sylvestris L.) wood were analyzed. For this aim, experimental specimens were manufactured from heat-treated material at temperatures of 140 °C, 160 °C, 180 °C and 200 °C for 3 hours. Three different experimental groups were prepared from the sapwood of the log. The first group was massive wood (wood), the second group was laminated veneer lumber (LVL), and the third group was reinforced laminated veneer lumber (RLVL) using glass fiber fabric. One-component polyurethane based adhesive was used as a binder in this study. Air-dry density, equilibrium moisture content (EMC), and compressive strength parallel to the grain were determined to analyze the effects of the reinforcement on the LVL composite. Test results showed that reinforced heat-treated LVL samples with glass fibers increased both air dry density and compressive strength parallel to the grain. On the other hand, the EMC values of the test samples decreased with increasing heat treatment temperature and reinforcement process. Improving the some physical and mechanical properties of heat-treated wood material can contribute to the widespread use in buildings.
- 30 June 2025
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 8 (1) , 156-171
Open AccessPerformance properties of heat treated and reinforced laminated veneer lumber with glass fiber
In this study, some technological properties of test samples manufactured from heat-treated scotch pine (Pinus sylvestris L.) wood were analyzed. For this aim, experimental specimens were manufactured from heat-treated material at temperatures of 140 °C, 160 °C, 180 °C and 200 °C for 3 hours. Three different experimental groups were prepared from the sapwood of the log. The first group was massive wood (wood), the second group was laminated veneer lumber (LVL), and the third group was reinforced laminated veneer lumber (RLVL) using glass fiber fabric. One-component polyurethane based adhesive was used as a binder in this study. Air-dry density, equilibrium moisture content (EMC), and compressive strength parallel to the grain were determined to analyze the effects of the reinforcement on the LVL composite. Test results showed that reinforced heat-treated LVL samples with glass fibers increased both air dry density and compressive strength parallel to the grain. On the other hand, the EMC values of the test samples decreased with increasing heat treatment temperature and reinforcement process. Improving the some physical and mechanical properties of heat-treated wood material can contribute to the widespread use in buildings.
- Open Access
- 28 December 2024
- Published by Necmettin Erbakan University in Konya Sanat, Necmettin Erbakan University
- No. 7,p. 254-263
Determining the Usage of Under Sink Cabinets in Residential Kitchens
In this research, it is intended to determine modes of use for undersink cabinets located in house kitchens and to determine the needs required in this volume of space. For this purpose 50 house kitchen undersink cabinets have been photographed while they are being used and materials-objects contained in them have been determined in Türkiye. In conclusion it has been determined that contained in the undersink cabinet are cleaning supplies (cleaning chemicals, bleach, vinegar, dish soap, cleaning bucket, etc.), foodstuff (oil, jarred food, food in plastic bags, etc.), small appliances and tools (oven-stove with single burner, toaster, small-large propane bottle, etc.), various utensils (plastic containers, pots, frying pans, trays, teapots, etc.), kitchen waste bin and water filtration appliance to varying extents. Of the undersink cabinets we examined, 40% has a single shelf within and 60% has no shelves. It was observed that due to careless design of the under-sink cabinets and failure to plan for the requirements, layouts are untidy and it was determined that the users use certain items such as cabinet door baskets, in-cabinet organizers, etc. in order to cope with this untidy layouts. Given the facts that oil and such materials as bleach etc. which stand side by side in the cabinet may react with each other in case of toppling or leakage, it might be suggested that such volumes must be planned very carefully and that users must be very careful against poisoning.
- 28 December 2024
- Published by Necmettin Erbakan University in Konya Sanat, Necmettin Erbakan University
- No. 7,p. 254-263
Open AccessDetermining the Usage of Under Sink Cabinets in Residential Kitchens
In this research, it is intended to determine modes of use for undersink cabinets located in house kitchens and to determine the needs required in this volume of space. For this purpose 50 house kitchen undersink cabinets have been photographed while they are being used and materials-objects contained in them have been determined in Türkiye. In conclusion it has been determined that contained in the undersink cabinet are cleaning supplies (cleaning chemicals, bleach, vinegar, dish soap, cleaning bucket, etc.), foodstuff (oil, jarred food, food in plastic bags, etc.), small appliances and tools (oven-stove with single burner, toaster, small-large propane bottle, etc.), various utensils (plastic containers, pots, frying pans, trays, teapots, etc.), kitchen waste bin and water filtration appliance to varying extents. Of the undersink cabinets we examined, 40% has a single shelf within and 60% has no shelves. It was observed that due to careless design of the under-sink cabinets and failure to plan for the requirements, layouts are untidy and it was determined that the users use certain items such as cabinet door baskets, in-cabinet organizers, etc. in order to cope with this untidy layouts. Given the facts that oil and such materials as bleach etc. which stand side by side in the cabinet may react with each other in case of toppling or leakage, it might be suggested that such volumes must be planned very carefully and that users must be very careful against poisoning.
- Open Access
- 29 December 2023
- Published by Necmettin Erbakan University in Konya Sanat, Necmettin Erbakan University
- No. 6,p. 25-41
İç Mekân Alanı Öğrencilerinin Mobilya Öğesine İlişkin Görüşleri
İç mekan tasarımı ve iç mimarlık öğrencileri eğitimleri boyunca iç mekan tasarımına yönelik farklı isim ve içeriklerde dersler almaktadırlar. Mekan tefrişlerinde çoğunlukla mobilyalar tasarlamakta ve iç mekanların tasarımını tamamlamaktadırlar. Bu araştırmanın amacı, iç mekan tasarımı ve iç mimarlık bölümlerinde öğrenim gören öğrencilerin iç mekan tasarım öğelerinden biri olan mobilya öğesi hakkındaki görüşlerini belirlemektir. Bu amaçla öğrencilere “İç mekan tasarımında mobilya bana…. ifade eder. Çünkü....” şeklinde açık uçlu bir maddenin bulunduğu formu doldurmaları istenmiştir. Ön lisans ve lisans öğrencileri tarafından doldurulan toplam 108 anket değerlendirmeye alınmıştır. Katılımcıların görüşleri incelendiğinde 47 farklı düşünce üretildiği görülmüştür. Geçerli görüşler içerik analizi yöntemi ile analiz edilmiştir. Analiz sonucunda görüşler ortak özellikleri dikkate alınarak on iki kavramsal kategori altında toplanmıştır. Bu kavramsal kategoriler; estetik (%30.83), rahatlık (%13.33), konfor (%10), eşya (%8.33), tasarım (%8.33), ihtiyaç (%5.83), insan için esas önemli olan yapı (%5.83), yapıya hayat veren öğe (%5), ergonomi (%3.33), tamamlayıcı öğe (%3.33), yaşam standardı (%3.33) ile kullanışlılık ve işlevsellik (%2.5) şeklindedir. Araştırma sonucunda öğrencilerin mobilya öğesini en fazla “estetik”, “rahatlık” ve “konfor” kavramları ile ilişkilendirdikleri görülmüştür. Öğrencilerin mobilyayı genel anlamda estetik, konfor, rahatlık, ergonomi, tasarım, kullanışlılık gibi teknik kavramlarla ve zorunlu bir ihtiyaç ve yaşamsal bir öğe olduğunu oluşturdukları düşüncelerle ifade etmeleri öğrencilerin bu kavramlara yakın ve tasarımlarında kullanacakları hissini vermektedir.
- 29 December 2023
- Published by Necmettin Erbakan University in Konya Sanat, Necmettin Erbakan University
- No. 6,p. 25-41
Open Accessİç Mekân Alanı Öğrencilerinin Mobilya Öğesine İlişkin Görüşleri
İç mekan tasarımı ve iç mimarlık öğrencileri eğitimleri boyunca iç mekan tasarımına yönelik farklı isim ve içeriklerde dersler almaktadırlar. Mekan tefrişlerinde çoğunlukla mobilyalar tasarlamakta ve iç mekanların tasarımını tamamlamaktadırlar. Bu araştırmanın amacı, iç mekan tasarımı ve iç mimarlık bölümlerinde öğrenim gören öğrencilerin iç mekan tasarım öğelerinden biri olan mobilya öğesi hakkındaki görüşlerini belirlemektir. Bu amaçla öğrencilere “İç mekan tasarımında mobilya bana…. ifade eder. Çünkü....” şeklinde açık uçlu bir maddenin bulunduğu formu doldurmaları istenmiştir. Ön lisans ve lisans öğrencileri tarafından doldurulan toplam 108 anket değerlendirmeye alınmıştır. Katılımcıların görüşleri incelendiğinde 47 farklı düşünce üretildiği görülmüştür. Geçerli görüşler içerik analizi yöntemi ile analiz edilmiştir. Analiz sonucunda görüşler ortak özellikleri dikkate alınarak on iki kavramsal kategori altında toplanmıştır. Bu kavramsal kategoriler; estetik (%30.83), rahatlık (%13.33), konfor (%10), eşya (%8.33), tasarım (%8.33), ihtiyaç (%5.83), insan için esas önemli olan yapı (%5.83), yapıya hayat veren öğe (%5), ergonomi (%3.33), tamamlayıcı öğe (%3.33), yaşam standardı (%3.33) ile kullanışlılık ve işlevsellik (%2.5) şeklindedir. Araştırma sonucunda öğrencilerin mobilya öğesini en fazla “estetik”, “rahatlık” ve “konfor” kavramları ile ilişkilendirdikleri görülmüştür. Öğrencilerin mobilyayı genel anlamda estetik, konfor, rahatlık, ergonomi, tasarım, kullanışlılık gibi teknik kavramlarla ve zorunlu bir ihtiyaç ve yaşamsal bir öğe olduğunu oluşturdukları düşüncelerle ifade etmeleri öğrencilerin bu kavramlara yakın ve tasarımlarında kullanacakları hissini vermektedir.
- 1 December 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 26 (4) , 1421-1429
Effects of Impregnation and Heat Treatment on Some Physical and Mechanical Properties of Wood Material
The aim of this study was to determine some physical and mechanical properties of spruce (Picea orientalis) wood, which was impregnated with aqueous solutions of valonia (valex) (the extract of Quercus ithaburensis), pine bark powder (pinex) (Pinus brutia Ten.) and gallnut powder (galex) (Quercus infectoria Oliver) as a pre-treatment and then heat treated. Test specimens were prepared from sapwood of spruce wood and impregnated with 10% tannin solutions before heat treatment base on ASTM D 1413-76. After pre-impregnation processs, specimens subjected to heat treatment at 150 °C, 175 °C and 200 °C for 2 h. The effect of impregnation process and heat treatment temperature on the air-dried density, compressive strength paralell to the grain (CS), bending strength (MOR) and modulus of elasticity in bending (MOE) were analyzed. As results, impregnation solutions showed positive effects on mechanical strength in unheat-treated samples and determined that mecnaical strength loses due to heat treatment slightly limited at low temperatures. However, strength loses increased with increasing temperature. The highest strength loses were also determined in impregnated samples with galex extract and heat-treated samples at 200 °C.
- 1 December 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 26 (4) , 1421-1429
Effects of Impregnation and Heat Treatment on Some Physical and Mechanical Properties of Wood Material
The aim of this study was to determine some physical and mechanical properties of spruce (Picea orientalis) wood, which was impregnated with aqueous solutions of valonia (valex) (the extract of Quercus ithaburensis), pine bark powder (pinex) (Pinus brutia Ten.) and gallnut powder (galex) (Quercus infectoria Oliver) as a pre-treatment and then heat treated. Test specimens were prepared from sapwood of spruce wood and impregnated with 10% tannin solutions before heat treatment base on ASTM D 1413-76. After pre-impregnation processs, specimens subjected to heat treatment at 150 °C, 175 °C and 200 °C for 2 h. The effect of impregnation process and heat treatment temperature on the air-dried density, compressive strength paralell to the grain (CS), bending strength (MOR) and modulus of elasticity in bending (MOE) were analyzed. As results, impregnation solutions showed positive effects on mechanical strength in unheat-treated samples and determined that mecnaical strength loses due to heat treatment slightly limited at low temperatures. However, strength loses increased with increasing temperature. The highest strength loses were also determined in impregnated samples with galex extract and heat-treated samples at 200 °C.
- 30 June 2023
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 6 (1) , 104-114
Isıl işlem uygulanmış karbon fiber ile güçlendirilmiş lamine kaplama kerestenin (LVL) hava kurusu yoğunluk ve liflere paralel basınç direncinin belirlenmesi
Isıl işlem, kimyasal madde kullanılmadan ağaç malzemenin bazı özelliklerinin iyileştirilmesi için geliştirilen çevre dostu bir odun modifikasyon yöntemidir ve son yıllarda Avrupa ve Dünya’da yaygın olarak kullanılmaya başlanmıştır. Isıl işlem, ahşap malzemede denge rutubet miktarını azaltmakta, boyutsal stabilizasyonu ve biyolojik direnci önemli derecede de artırmaktadır. Bu çalışma, ısıl işlem uygulanmış ahşap malzemelerden farklı tutkallarla yapıştırılarak ve karbon fiber kumaş ile güçlendirilerek üretilen lamine kaplama kerestelerin (LVL) hava kurusu yoğunluk ve liflere paralel basınç direnci değerlerindeki değişimlerin belirlenmesi amacıyla yapılmıştır. Bu maksatla karaçam (Pinus nigra) ahşap malzemeler, 150, 175 ve 200 °C’de 2 saat ısıl işlem uygulandıktan sonra uygun boyutlarda kesilmiş, poliüretan (PU) ve polivinil asetat (PVAc) tutkalları kullanılarak lamine edilmiştir. Lamine kompozit malzemenin özelliklerini iyileştirmek için ahşap kaplamalar arasına takviye tabakası olarak karbon fiberler eklenmiştir. Test sonuçları ısıl işlemin, hava kurusu yoğunluk değerleri ve liflere paralel basınç direncini azalttığını göstermiştir. Öte yandan güçlendirme işlemi hava kurusu yoğunluk ve liflere paralel basınç direncinin ikisini de artırmıştır.
- 30 June 2023
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 6 (1) , 104-114
Isıl işlem uygulanmış karbon fiber ile güçlendirilmiş lamine kaplama kerestenin (LVL) hava kurusu yoğunluk ve liflere paralel basınç direncinin belirlenmesi
Isıl işlem, kimyasal madde kullanılmadan ağaç malzemenin bazı özelliklerinin iyileştirilmesi için geliştirilen çevre dostu bir odun modifikasyon yöntemidir ve son yıllarda Avrupa ve Dünya’da yaygın olarak kullanılmaya başlanmıştır. Isıl işlem, ahşap malzemede denge rutubet miktarını azaltmakta, boyutsal stabilizasyonu ve biyolojik direnci önemli derecede de artırmaktadır. Bu çalışma, ısıl işlem uygulanmış ahşap malzemelerden farklı tutkallarla yapıştırılarak ve karbon fiber kumaş ile güçlendirilerek üretilen lamine kaplama kerestelerin (LVL) hava kurusu yoğunluk ve liflere paralel basınç direnci değerlerindeki değişimlerin belirlenmesi amacıyla yapılmıştır. Bu maksatla karaçam (Pinus nigra) ahşap malzemeler, 150, 175 ve 200 °C’de 2 saat ısıl işlem uygulandıktan sonra uygun boyutlarda kesilmiş, poliüretan (PU) ve polivinil asetat (PVAc) tutkalları kullanılarak lamine edilmiştir. Lamine kompozit malzemenin özelliklerini iyileştirmek için ahşap kaplamalar arasına takviye tabakası olarak karbon fiberler eklenmiştir. Test sonuçları ısıl işlemin, hava kurusu yoğunluk değerleri ve liflere paralel basınç direncini azalttığını göstermiştir. Öte yandan güçlendirme işlemi hava kurusu yoğunluk ve liflere paralel basınç direncinin ikisini de artırmıştır.
- Open Access
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 33 (1) , e20230007
Influence of carbon fibre layers on the strength of thermally modified laminated veneer lumber
Thermally modification of wood is an environment-friendly alternative method for improving several properties of wood without the use of chemicals. The compressive strength (CS) parallel to the grain of reinforced laminated veneer lumber (LVL) manufactured from heat treated beech (Fagus orientalis) veneers and carbon fibre was determined. Thermally modification was performed at 140°C, 160°C, 180°C, and 200 °C according to thermal treatment process. Carbon fibre were added as a reinforcement layer between wood veneers bonded with phenol-formaldehyde (PF), polyvinyl acetate (PVAc) polyurethane adhesives (PU) to improve properties of LVL. Results showed that reinforcing LVL panels with carbon fibre increased both density and CS. The PF adhesive showed better results for reinforced LVL panels with carbon fibre. The anatomical structure and density of the wood material significantly affect its mechanical properties, including compressive strength parallel to the grains. Wood density had a strong significant linear relationship with CS.
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 33 (1) , e20230007
Open AccessInfluence of carbon fibre layers on the strength of thermally modified laminated veneer lumber
Thermally modification of wood is an environment-friendly alternative method for improving several properties of wood without the use of chemicals. The compressive strength (CS) parallel to the grain of reinforced laminated veneer lumber (LVL) manufactured from heat treated beech (Fagus orientalis) veneers and carbon fibre was determined. Thermally modification was performed at 140°C, 160°C, 180°C, and 200 °C according to thermal treatment process. Carbon fibre were added as a reinforcement layer between wood veneers bonded with phenol-formaldehyde (PF), polyvinyl acetate (PVAc) polyurethane adhesives (PU) to improve properties of LVL. Results showed that reinforcing LVL panels with carbon fibre increased both density and CS. The PF adhesive showed better results for reinforced LVL panels with carbon fibre. The anatomical structure and density of the wood material significantly affect its mechanical properties, including compressive strength parallel to the grains. Wood density had a strong significant linear relationship with CS.
- 7 October 2022
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 38 (2) , 653-664
Karbon fiber ve cam fiber ile güçlendirilmiş ısıl işlem uygulanmış lamine kaplama kerestelerin (lvl) bazı fiziksel ve mekaniksel özellikleri
Ahşap, yaygın olarak kullanılan en eski yapı malzemelerden birisidir. Farklı alanlarda da farklı amaçlarla kullanımına yönelik giderek artan bir talep vardır. Bu talebi karşılayabilmek için ahşap esaslı yapısal kompozitler geliştirilmiştir. Bu çalışmada, ısıl işlem uygulanmış ve fenol formaldehit (FF) tutkalı kullanılarak karbon ve cam elyaf ile güçlendirilmiş kayın (Fagus orientalis Lipsky) kompozit örneklerin bazı fiziksel ve mekaniksel özellikleri araştırılmıştır. Bu amaçla ahşap malzemelere 150, 175 ve 200°C sıcaklıkta 3 saat süre ile ısıl işlem uygulanmış ve deney örnekleri hazırlanmıştır. Test sonuçları, karbon ve cam elyaf ile güçlendirilmiş örneklerin eğilme direnci (MOR) ve eğilmede elastikiyet modülü (MOE) değerlerini artırdığını göstermiştir. Bununla birlikte liflere paralel basınç direnci (CS//) değerlerinde, uygulanan ısıl işlem sıcaklığına ve güçlendirici malzeme türüne göre önemli değişikliklere neden olurken, liflere paralel yapışma direnci (SS) değerlerinde düşüşler belirlenmiştir. Genel olarak, karbon fiber ile güçlendirilmiş deney örneklerin MOR ve MOE değerleri, cam elyaf ile güçlendirilmiş örneklerden daha yüksek, CS// ve SS değerleri ise daha düşük belirlenmiştir.
- 7 October 2022
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 38 (2) , 653-664
Karbon fiber ve cam fiber ile güçlendirilmiş ısıl işlem uygulanmış lamine kaplama kerestelerin (lvl) bazı fiziksel ve mekaniksel özellikleri
Ahşap, yaygın olarak kullanılan en eski yapı malzemelerden birisidir. Farklı alanlarda da farklı amaçlarla kullanımına yönelik giderek artan bir talep vardır. Bu talebi karşılayabilmek için ahşap esaslı yapısal kompozitler geliştirilmiştir. Bu çalışmada, ısıl işlem uygulanmış ve fenol formaldehit (FF) tutkalı kullanılarak karbon ve cam elyaf ile güçlendirilmiş kayın (Fagus orientalis Lipsky) kompozit örneklerin bazı fiziksel ve mekaniksel özellikleri araştırılmıştır. Bu amaçla ahşap malzemelere 150, 175 ve 200°C sıcaklıkta 3 saat süre ile ısıl işlem uygulanmış ve deney örnekleri hazırlanmıştır. Test sonuçları, karbon ve cam elyaf ile güçlendirilmiş örneklerin eğilme direnci (MOR) ve eğilmede elastikiyet modülü (MOE) değerlerini artırdığını göstermiştir. Bununla birlikte liflere paralel basınç direnci (CS//) değerlerinde, uygulanan ısıl işlem sıcaklığına ve güçlendirici malzeme türüne göre önemli değişikliklere neden olurken, liflere paralel yapışma direnci (SS) değerlerinde düşüşler belirlenmiştir. Genel olarak, karbon fiber ile güçlendirilmiş deney örneklerin MOR ve MOE değerleri, cam elyaf ile güçlendirilmiş örneklerden daha yüksek, CS// ve SS değerleri ise daha düşük belirlenmiştir.
- 30 June 2022
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 5 (1) , 17-28
Effects of heat treatment on surface roughness and bonding strength of wood material
The purpose of this paper is to determine the effects of heat treatment on some properties of black pine (Pinus nigra A.) and larex (Larix decidua), woods. For this purpose, test samples were heat treated at 140, 160, 180 and 200°C for 2 and 5 hours. The air-dried density, equilibrium moisture content (EMC), surface roughness and bonding strengths of the test samples were analyzed. The average surface roughness parameter (Ra) was analyzed parallel to the grains. The results indicated significant differences depending on the wood species, heat treatment temperatures and treatment times. Based on the findings in this study, all parameters decreased depending on the heat treatment conditions. The density and EMC values of the control specimens were higher than the heat-treated samples. Also the surface roughness values obtained in black pine samples were higher than larex samples. On the other hand, bonding strength values obtained in larex samples were significantly higher than that of black pine samples. These parameters should be taken into account in the application areas of heat-treated wood material, the usage amount of which is constantly evolving in the woodworking industry.
- 30 June 2022
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 5 (1) , 17-28
Effects of heat treatment on surface roughness and bonding strength of wood material
The purpose of this paper is to determine the effects of heat treatment on some properties of black pine (Pinus nigra A.) and larex (Larix decidua), woods. For this purpose, test samples were heat treated at 140, 160, 180 and 200°C for 2 and 5 hours. The air-dried density, equilibrium moisture content (EMC), surface roughness and bonding strengths of the test samples were analyzed. The average surface roughness parameter (Ra) was analyzed parallel to the grains. The results indicated significant differences depending on the wood species, heat treatment temperatures and treatment times. Based on the findings in this study, all parameters decreased depending on the heat treatment conditions. The density and EMC values of the control specimens were higher than the heat-treated samples. Also the surface roughness values obtained in black pine samples were higher than larex samples. On the other hand, bonding strength values obtained in larex samples were significantly higher than that of black pine samples. These parameters should be taken into account in the application areas of heat-treated wood material, the usage amount of which is constantly evolving in the woodworking industry.
- 30 August 2021
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 17 (6) , 887-894
Effects of impregnation and heat treatment on density, bending and compression properties of black pine (Pinus nigraArnold) wood
This study aims to study the improvement in the properties of heat-treated wood material by impregnation. For this purpose, black pine (Pinus nigra Arnold) wood specimens were modified in two stages: impregnation with 1%, 3% and 5% of diammonium phosphate (DAP) and sodium carbonate (SC) compounds followed by heat treatment at four different temperatures. Test specimens were pre-treated with solutions of different pH values of either DAP or SC solutions according to the immersion method and they were exposed to heat treatments at 150°C, 170°C, 190°C and 210°C for 3 h. Some physical and mechanical properties were determined in combined treated specimens with air-dried density, compression strength parallel to grain (CS) and bending strength (MOR). The test results indicated that, as regards the effect of the heat treatment, the mechanical strength decreased due to the increase in temperature, while the losses in the CS were fewer than those of the MOR. In addition, generally combined treatments increased the mechanical properties of the specimens, especially at lower and moderate heat treatment temperatures. Moreover, the SC compound showed more favorable results against the reducing effect of the heat treatment on mechanical strengths.
- 30 August 2021
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 17 (6) , 887-894
Effects of impregnation and heat treatment on density, bending and compression properties of black pine (Pinus nigraArnold) wood
This study aims to study the improvement in the properties of heat-treated wood material by impregnation. For this purpose, black pine (Pinus nigra Arnold) wood specimens were modified in two stages: impregnation with 1%, 3% and 5% of diammonium phosphate (DAP) and sodium carbonate (SC) compounds followed by heat treatment at four different temperatures. Test specimens were pre-treated with solutions of different pH values of either DAP or SC solutions according to the immersion method and they were exposed to heat treatments at 150°C, 170°C, 190°C and 210°C for 3 h. Some physical and mechanical properties were determined in combined treated specimens with air-dried density, compression strength parallel to grain (CS) and bending strength (MOR). The test results indicated that, as regards the effect of the heat treatment, the mechanical strength decreased due to the increase in temperature, while the losses in the CS were fewer than those of the MOR. In addition, generally combined treatments increased the mechanical properties of the specimens, especially at lower and moderate heat treatment temperatures. Moreover, the SC compound showed more favorable results against the reducing effect of the heat treatment on mechanical strengths.