Ruan Moreira Ferraz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ruan Moreira Ferraz has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Guilherme Marcio Soares
Federal University of Juiz de Fora (UFJF)
4 shared publications - Henrique Antonio Carvalho Braga
Federal University of Juiz de Fora
4 shared publications - Lucas Henrique Gomes Resende
Federal Technological Education Center Celso Suckow da Fonseca (CEFET/RJ), Nova Friburgo, Rio de Janeiro, Brazil
4 shared publications - Pedro Santos Almeida
Federal University of Juiz de Fora (UFJF)
4 shared publications - Jose Marcos Alonso
Department of Electrical Engineering, University of Oviedo, Asturias, Spain
2 shared publications
Latest Publications
- Open Access
- 19 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 165598-165606
Impact of LED Current Waveforms on FSK-Based VLC Performance and Design of a Flyback Driver for Square-Wave Modulation
This paper analyzes the performance of Visible Light Communication (VLC) systems when different LED current waveforms are applied, aiming to guide the design of switched-mode converters using Frequency Shift Keying (FSK) modulation schemes. Both theoretical calculations and experimental tests were conducted for sinusoidal, triangular, and square current waveforms, revealing that the square waveform provides superior noise immunity, allowing transmission over distances up to three times longer than the other waveform types while maintaining a satisfactory Bit Error Rate (BER). Furthermore, the work presents a method for designing an LED driver capable of producing square-shaped current signals, based on a flyback converter operating in Continuous Conduction Mode (CCM). This topology enables single-switch control of both the average current and the data modulation. A laboratory prototype rated at 35-W and powered by a 300-V DC supply with a 13.7-V ripple was built and tested, demonstrating reliable data transmission over distances of up to 3 meters, achieving satisfactory BER and reaching data rates of 234 kb/s.
- 19 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 165598-165606
Open AccessImpact of LED Current Waveforms on FSK-Based VLC Performance and Design of a Flyback Driver for Square-Wave Modulation
This paper analyzes the performance of Visible Light Communication (VLC) systems when different LED current waveforms are applied, aiming to guide the design of switched-mode converters using Frequency Shift Keying (FSK) modulation schemes. Both theoretical calculations and experimental tests were conducted for sinusoidal, triangular, and square current waveforms, revealing that the square waveform provides superior noise immunity, allowing transmission over distances up to three times longer than the other waveform types while maintaining a satisfactory Bit Error Rate (BER). Furthermore, the work presents a method for designing an LED driver capable of producing square-shaped current signals, based on a flyback converter operating in Continuous Conduction Mode (CCM). This topology enables single-switch control of both the average current and the data modulation. A laboratory prototype rated at 35-W and powered by a 300-V DC supply with a 13.7-V ripple was built and tested, demonstrating reliable data transmission over distances of up to 3 meters, achieving satisfactory BER and reaching data rates of 234 kb/s.
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (4) , 6605-6617
Optimization-Based Design of an Off-Line LED Driver Based on the LLC Resonant Converter With Active Ripple Compensation
This paper presents a design methodology for designing an off-line light-emitting diode (LED) driver, aiming to improve its efficiency, lifespan, and volume. The approach considers the entire design process as a nonlinear constrained optimization problem and allows for simultaneous design of power circuit elements and the controller, which uses a frequency-based active ripple compensation (ARC). By applying the ARC technique, the design achieves a substantial reduction in bulk capacitance, enhancing both lifespan and compactness. The proposed strategy provides flexibility, allowing designers to prioritize key performance indicators-such as reliability, volume, and power losses-according to specific design objectives. In order to verify the feasibility of the design procedure, the strategy was employed to a compact two-stage integrated topology based on the integration of a totem-pole bridgeless boost PFC and a half-bridge LLC resonant converter. Experimental results obtained from a 96-W laboratory prototype supplied from a 127-V 60-Hz mains voltage attested the superior performance of the optimized design. The proposed approach enabled an approximate 92% reduction in bus capacitance and a 30% reduction in overall driver volume compared to the conventional design methodology.
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (4) , 6605-6617
Optimization-Based Design of an Off-Line LED Driver Based on the LLC Resonant Converter With Active Ripple Compensation
This paper presents a design methodology for designing an off-line light-emitting diode (LED) driver, aiming to improve its efficiency, lifespan, and volume. The approach considers the entire design process as a nonlinear constrained optimization problem and allows for simultaneous design of power circuit elements and the controller, which uses a frequency-based active ripple compensation (ARC). By applying the ARC technique, the design achieves a substantial reduction in bulk capacitance, enhancing both lifespan and compactness. The proposed strategy provides flexibility, allowing designers to prioritize key performance indicators-such as reliability, volume, and power losses-according to specific design objectives. In order to verify the feasibility of the design procedure, the strategy was employed to a compact two-stage integrated topology based on the integration of a totem-pole bridgeless boost PFC and a half-bridge LLC resonant converter. Experimental results obtained from a 96-W laboratory prototype supplied from a 127-V 60-Hz mains voltage attested the superior performance of the optimized design. The proposed approach enabled an approximate 92% reduction in bus capacitance and a 30% reduction in overall driver volume compared to the conventional design methodology.
- 23 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (10) , 12209-12220
Frequency-Based Active Ripple Compensation Technique to Reduce Bulk Capacitance in Integrated Offline LED Drivers
In order to increase the power density and the lifespan of light-emitting diodes (LED) drivers, several studies have proposed active ripple compensation (ARC) techniques for minimizing the converter bulk capacitance. However, a common side effect of the ARC method is the increase in the total harmonic distortion (THD) of the converter input current. In this context, a frequency-based ARC technique is proposed as an alternative to the conventional ARC methodology, in which the duty cycle is modulated. The analyses presented in this article show that the frequency-based ARC approach applied to resonant converters has a better performance than the one used in hard-switching converters, since it allows for a huge capacitance reduction with a small THD increase. Furthermore, this article presents a generalized analysis of ARC techniques applied to integrated offline LED drivers, which reduce the number of components and the overall LED driver cost. The input current harmonic content and the output ripple reduction have been theoretically predicted for several converters. Experimental results gathered from a 96-W laboratory prototype supplied from a 127-V 60-Hz grid attested the superior performance of the frequency-based active ripple compensation, since a capacitance reduction of 66.6% has been obtained with an increase of only 0.9% in the THD.
- 23 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (10) , 12209-12220
Frequency-Based Active Ripple Compensation Technique to Reduce Bulk Capacitance in Integrated Offline LED Drivers
In order to increase the power density and the lifespan of light-emitting diodes (LED) drivers, several studies have proposed active ripple compensation (ARC) techniques for minimizing the converter bulk capacitance. However, a common side effect of the ARC method is the increase in the total harmonic distortion (THD) of the converter input current. In this context, a frequency-based ARC technique is proposed as an alternative to the conventional ARC methodology, in which the duty cycle is modulated. The analyses presented in this article show that the frequency-based ARC approach applied to resonant converters has a better performance than the one used in hard-switching converters, since it allows for a huge capacitance reduction with a small THD increase. Furthermore, this article presents a generalized analysis of ARC techniques applied to integrated offline LED drivers, which reduce the number of components and the overall LED driver cost. The input current harmonic content and the output ripple reduction have been theoretically predicted for several converters. Experimental results gathered from a 96-W laboratory prototype supplied from a 127-V 60-Hz grid attested the superior performance of the frequency-based active ripple compensation, since a capacitance reduction of 66.6% has been obtained with an increase of only 0.9% in the THD.
- 3 September 2021
- Published by Springer Nature in Journal of Control, Automation and Electrical Systems
- Vol. 32 (6) , 1758-1770
A Novel Design Approach for LLC Resonant Converters in Off-line LED Driving Applications
- 3 September 2021
- Published by Springer Nature in Journal of Control, Automation and Electrical Systems
- Vol. 32 (6) , 1758-1770
A Novel Design Approach for LLC Resonant Converters in Off-line LED Driving Applications