Serkan Simsek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Serkan Simsek has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Agah Oktay Ertay
Faculty of Engineering and Architecture, Department of Electrical and Electronics Engineering, Erzincan Binali Yildirim University, Yalnizbag Campus, Erzincan 24002, Türkiye
3 shared publications - Cem Çindaş
ASELSAN Inc., Ankara, Türkiye
1 shared publication - Durmus Gebesoglu
Radar, Electronic Warfare and Intelligence Systems Group, Aselsan Inc., Ankara, Turkey
1 shared publication - Onur Erkan
Istanbul Technical University
1 shared publication
Latest Publications
- Open Access
- 23 July 2026
- Published by AVES YAYINCILIK A.Ş. in Electrica
- Vol. 26, 1-14
Design of a Compact Analog I/Q Type Vector Modulator in S-Band for Phased Array Antennas
This study presents the design of a compact analog I-Q type vector modulator (VM) for phased array systems in the S-band. The design and implementation of the subcomponents of the produced VM, which are a stripline-based symmetric coupled directional coupler, two 0°/180° bi-phase modulators, two analog variable attenuators, and a Wilkinson combiner, are realized in detail. Bi-phase modulators, analog variable attenuators, and a Wilkinson combiner were combined on a single board using RO4003 material. Simulations were performed in the Computer Simulation Technology (CST) and AWR Applied Wave Research (AWR) Design Environments. The measurement results of the produced VM show a dynamic range of around 30 dB, a 360° phase shift range, a phase resolution of 0.5°, 12 dB insertion loss at 3 GHz, and a return loss higher than 10 dB between 2 and 4 GHz. Moreover, in this study, a compact analog I-Q type VM has been designed and fabricated with lower insertion loss than available literature, considering similar operating bands. Cite this article as: C. Çindaş and S. Şimşek, “Design of a compact analog I/Q type vector modulator in S-band for phased array antennas,” Electrica, 2026, 26, 0293, doi: 10.5152/electrica.2026.25293.
- 23 July 2026
- Published by AVES YAYINCILIK A.Ş. in Electrica
- Vol. 26, 1-14
Open AccessDesign of a Compact Analog I/Q Type Vector Modulator in S-Band for Phased Array Antennas
This study presents the design of a compact analog I-Q type vector modulator (VM) for phased array systems in the S-band. The design and implementation of the subcomponents of the produced VM, which are a stripline-based symmetric coupled directional coupler, two 0°/180° bi-phase modulators, two analog variable attenuators, and a Wilkinson combiner, are realized in detail. Bi-phase modulators, analog variable attenuators, and a Wilkinson combiner were combined on a single board using RO4003 material. Simulations were performed in the Computer Simulation Technology (CST) and AWR Applied Wave Research (AWR) Design Environments. The measurement results of the produced VM show a dynamic range of around 30 dB, a 360° phase shift range, a phase resolution of 0.5°, 12 dB insertion loss at 3 GHz, and a return loss higher than 10 dB between 2 and 4 GHz. Moreover, in this study, a compact analog I-Q type VM has been designed and fabricated with lower insertion loss than available literature, considering similar operating bands. Cite this article as: C. Çindaş and S. Şimşek, “Design of a compact analog I/Q type vector modulator in S-band for phased array antennas,” Electrica, 2026, 26, 0293, doi: 10.5152/electrica.2026.25293.
- Open Access
- 26 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 42234-42247
Investigation of AFGSM Methods for Some Electromagnetic Bandgap Structures: From Analysis to Applied Antenna Design
Electromagnetic Bandgap (EBG) structures that exhibit various performances, such as preventing the electromagnetic wave propagation and reflecting an incident wave within the stopband, have unique electromagnetic characterization. Due to this reason, accurate analysis and design of the EBG structures are crucial to enhance the integrated system performance. This paper concentrates on the characterization of some planar EBGs using the Auxiliary Functions of Generalized Scattering Matrix (AFGSM) methods, with particular importance on an in-depth consideration of its bandgaps. The AFGSM method is applied to the planar EBG structures in the literature for the first time. The well-known kinds (symmetric and asymmetric cases) of mushroom type and multilayer EBG structures are considered to verify the presented method. Analysis results are compared with the Conventional Eigenvalue Equation (C-EIV) and the Generalized Scattering Matrix based Eigenvalue Equation (GSM-EIV) methods. Low computation load and accurate results are obtained to analyze the planar EBG structures with the AFGSM method due to using transmission line model. In addition, a design methodology is proposed for a chosen planar EBG structure using the AFGSM methods. Geometrical parameters of interested EBG problems are determined for acquiring the stopband frequency region of interest using the scattering parameters of unit cell configuration. The mushroom EBG model along one and two-dimensional axes is used in an antenna application to decrease mutual coupling between antenna elements. Three different scenarios are simulated in the HFSS electromagnetic simulation design environment to understand the effect of mutual coupling reduction in the antenna problem of the designed EBG structure via the AFGSM method. All designed antennas are manufactured, and the measurement results are in good agreement with the simulation results. The measurement results of the fabricated antenna application example including designed EBG using the proposed AFGSM method is compared with the existing similar problems with the same and different EBG models. It has been demonstrated that bandgap analysis, design of the planar EBG structures and integration of considered EBG model to a design application can be accurately and quickly achieved with the given methodology using the AFGSM method.
- 26 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 42234-42247
Open AccessInvestigation of AFGSM Methods for Some Electromagnetic Bandgap Structures: From Analysis to Applied Antenna Design
Electromagnetic Bandgap (EBG) structures that exhibit various performances, such as preventing the electromagnetic wave propagation and reflecting an incident wave within the stopband, have unique electromagnetic characterization. Due to this reason, accurate analysis and design of the EBG structures are crucial to enhance the integrated system performance. This paper concentrates on the characterization of some planar EBGs using the Auxiliary Functions of Generalized Scattering Matrix (AFGSM) methods, with particular importance on an in-depth consideration of its bandgaps. The AFGSM method is applied to the planar EBG structures in the literature for the first time. The well-known kinds (symmetric and asymmetric cases) of mushroom type and multilayer EBG structures are considered to verify the presented method. Analysis results are compared with the Conventional Eigenvalue Equation (C-EIV) and the Generalized Scattering Matrix based Eigenvalue Equation (GSM-EIV) methods. Low computation load and accurate results are obtained to analyze the planar EBG structures with the AFGSM method due to using transmission line model. In addition, a design methodology is proposed for a chosen planar EBG structure using the AFGSM methods. Geometrical parameters of interested EBG problems are determined for acquiring the stopband frequency region of interest using the scattering parameters of unit cell configuration. The mushroom EBG model along one and two-dimensional axes is used in an antenna application to decrease mutual coupling between antenna elements. Three different scenarios are simulated in the HFSS electromagnetic simulation design environment to understand the effect of mutual coupling reduction in the antenna problem of the designed EBG structure via the AFGSM method. All designed antennas are manufactured, and the measurement results are in good agreement with the simulation results. The measurement results of the fabricated antenna application example including designed EBG using the proposed AFGSM method is compared with the existing similar problems with the same and different EBG models. It has been demonstrated that bandgap analysis, design of the planar EBG structures and integration of considered EBG model to a design application can be accurately and quickly achieved with the given methodology using the AFGSM method.
- 7 September 2021
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 50 (2) , 507-524
Detection of band edge frequencies in symmetric/asymmetric dielectric loaded helix slow‐wave structures
- 7 September 2021
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 50 (2) , 507-524
Detection of band edge frequencies in symmetric/asymmetric dielectric loaded helix slow‐wave structures
- 19 December 2019
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 7 (4) , 744-750
INVESTIGATION OF OMNIDIRECTIONAL BANDGAPS IN PHOTONIC CRYSTALS
Tr en Kablolu ve kablosuz ağ teknolojilerinde veri kullanım oranının artması taşıyıcı ortamdaki bant genişliklerinin daha etkin kullanıması gerekliliğini ortaya çıkarmıştır. Gelişen malzeme teknolojisi sayesinde nanometre boyutlarında düşük güçle çalışan ve optik spektrumun verimli kullanılmasını sağlayan bileşenlerin tasarlanması mümkün hale gelmiştir. Bu çalışmada optik frekans bölgesindeki uygulamalarda kullanılan geliş açısı ve kutuplanmadan bağımsız tümyönlü yansıtıcı bileşeninin analiz ve tasarımı yapılmıştır. Tümyönlü yansıtıcının bant kenar frekanslarının belirlenmesinde, bilinen sayısal yöntemlere alternatif olarak daha hızlı ve yüksek doğrulukta sonuç veren genelleştirilmiş saçılma matrisi yardımcı fonksiyonları (AFGSM) yöntemi kullanılmıştır. Önerilen alternatif yöntem ile periyodiklik koşulu altında istenen tümyönlü yansıtıcı parametrelerini sağlayan fotonik kristalli dielektrik malzemeler uygun şekilde seçilmiş (Te, Ta2O5, TiO2) ve elde edilen sonuçlar bilgisayar benzetimleri ile doğrulanmıştır. Tasarımı yapılan yansıtıcı, optik dalgaboyu bölgesinde %56.63’lük tümyönlü bağıl bant genişliği (ORB) değerine sahip, 924 nm – 1654 nm aralığında tümyönlü fotonik durdurma bandı (OBG) sağlamaktadır. Rapidly increasing data usage rates in fixed and wireless technologies encouraged the researches to find alternative ways of using limited bandwidth in carrier medium more efficiently. Recent developments in material science, particularly in nanometer scale, allowed engineers to design low power components that can ensure efficient use of optical spectrum. In this study, we designed an omnidirectional reflector that can be used as an optical component without any dependency on polarization or angle of incidence. Band edge frequencies of omnidirectional reflector are determined by employing auxiliary functions of generalized scattering matrix (AFGSM) method which provides faster and accurate estimates in comparison to conventional methods existing in the literature. Using the proposed method proper photonic crystal structures (Te, Ta2O5, TiO2) are selected according to given design objective while satisfying the periodicity condition. Computer simulation results are given for verification. The designed reflector provides an omnidirectional relative bandwidth (ORB) value of 56.63% with an omnidirectional photonic bandgap (OBG) in the range of 924 nm to 1654 nm in optical wavelength region.
- 19 December 2019
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 7 (4) , 744-750
INVESTIGATION OF OMNIDIRECTIONAL BANDGAPS IN PHOTONIC CRYSTALS
Tr en Kablolu ve kablosuz ağ teknolojilerinde veri kullanım oranının artması taşıyıcı ortamdaki bant genişliklerinin daha etkin kullanıması gerekliliğini ortaya çıkarmıştır. Gelişen malzeme teknolojisi sayesinde nanometre boyutlarında düşük güçle çalışan ve optik spektrumun verimli kullanılmasını sağlayan bileşenlerin tasarlanması mümkün hale gelmiştir. Bu çalışmada optik frekans bölgesindeki uygulamalarda kullanılan geliş açısı ve kutuplanmadan bağımsız tümyönlü yansıtıcı bileşeninin analiz ve tasarımı yapılmıştır. Tümyönlü yansıtıcının bant kenar frekanslarının belirlenmesinde, bilinen sayısal yöntemlere alternatif olarak daha hızlı ve yüksek doğrulukta sonuç veren genelleştirilmiş saçılma matrisi yardımcı fonksiyonları (AFGSM) yöntemi kullanılmıştır. Önerilen alternatif yöntem ile periyodiklik koşulu altında istenen tümyönlü yansıtıcı parametrelerini sağlayan fotonik kristalli dielektrik malzemeler uygun şekilde seçilmiş (Te, Ta2O5, TiO2) ve elde edilen sonuçlar bilgisayar benzetimleri ile doğrulanmıştır. Tasarımı yapılan yansıtıcı, optik dalgaboyu bölgesinde %56.63’lük tümyönlü bağıl bant genişliği (ORB) değerine sahip, 924 nm – 1654 nm aralığında tümyönlü fotonik durdurma bandı (OBG) sağlamaktadır. Rapidly increasing data usage rates in fixed and wireless technologies encouraged the researches to find alternative ways of using limited bandwidth in carrier medium more efficiently. Recent developments in material science, particularly in nanometer scale, allowed engineers to design low power components that can ensure efficient use of optical spectrum. In this study, we designed an omnidirectional reflector that can be used as an optical component without any dependency on polarization or angle of incidence. Band edge frequencies of omnidirectional reflector are determined by employing auxiliary functions of generalized scattering matrix (AFGSM) method which provides faster and accurate estimates in comparison to conventional methods existing in the literature. Using the proposed method proper photonic crystal structures (Te, Ta2O5, TiO2) are selected according to given design objective while satisfying the periodicity condition. Computer simulation results are given for verification. The designed reflector provides an omnidirectional relative bandwidth (ORB) value of 56.63% with an omnidirectional photonic bandgap (OBG) in the range of 924 nm to 1654 nm in optical wavelength region.
- 19 December 2019
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 7 (4) , 715-724
YÜRÜYEN DALGALI TÜP KUVVETLENDİRİCİLERİNDE İLETİM SABİTLERİNİN İNCELENMESİ
Bu çalışmada tipik bir yürüyen dalgalı tüp kuvvetlendiricisindeki (TWT) elektron demeti ile elektromanyetik dalganın etkileşimi sonucu elde edilen TWT iletim sabitlerinin davranışı incelenmiştir. Öncelikle, TWT demet dalga etkileşiminden dispersiyon denklemi çıkarılmıştır. Elde edilen denklem, Pierce normalizasyon parametreleri kullanılarak basitleştirilmiştir. Farklı Pierce normalizasyon parametre takımları için TWT’ye ait tüm dalga tipi çözümlerin davranışları TWT’nin artırılmış iletim sabitlerine bakılarak tespit edilmiştir. Bu bağlamda üç ana durum ele alınmıştır. Bu üç ana durumun her birinde sırasıyla sadece senkronizasyon, uzay yükü ve devre kaybı parametreleri belirli bir değer aralıklarında süpürülmüştür ve ilgili diğer normalizasyon parametreleri sabit alınmıştır. Böylece TWT’deki dalga tipi çözümlerin artırılmış iletim sabitlerinin kök-yer eğrileri derinlemesine incelenmiştir.
- 19 December 2019
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 7 (4) , 715-724
YÜRÜYEN DALGALI TÜP KUVVETLENDİRİCİLERİNDE İLETİM SABİTLERİNİN İNCELENMESİ
Bu çalışmada tipik bir yürüyen dalgalı tüp kuvvetlendiricisindeki (TWT) elektron demeti ile elektromanyetik dalganın etkileşimi sonucu elde edilen TWT iletim sabitlerinin davranışı incelenmiştir. Öncelikle, TWT demet dalga etkileşiminden dispersiyon denklemi çıkarılmıştır. Elde edilen denklem, Pierce normalizasyon parametreleri kullanılarak basitleştirilmiştir. Farklı Pierce normalizasyon parametre takımları için TWT’ye ait tüm dalga tipi çözümlerin davranışları TWT’nin artırılmış iletim sabitlerine bakılarak tespit edilmiştir. Bu bağlamda üç ana durum ele alınmıştır. Bu üç ana durumun her birinde sırasıyla sadece senkronizasyon, uzay yükü ve devre kaybı parametreleri belirli bir değer aralıklarında süpürülmüştür ve ilgili diğer normalizasyon parametreleri sabit alınmıştır. Böylece TWT’deki dalga tipi çözümlerin artırılmış iletim sabitlerinin kök-yer eğrileri derinlemesine incelenmiştir.