James L. White
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
James L. White has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Haifeng Shan
Center for Advanced Engineering Fibers and Films, Clemson University , Clemson, South Carolina, USA
1 shared publication Jaein Suh
Institute of Polymer Engineering, The University of Akron, Akron, Ohio 44325
1 shared publication- Jinhai Yang
Anyang, 455002 P.R. China; Zhengzhou University
1 shared publication Sungtae Ahn
Institute of Polymer Engineering, University of Akron, Akron, Ohio 44325
1 shared publication
Latest Publications
- 19 June 2007
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 106 (1) , 276-282
Comparative study on quiescent crystallization kinetics of isotactic polyolefins
Quiescent melt crystallization rates of various polyolefins including high density polyethylene (PE), isotactic form of polypropylene (PP), polybutene‐1 (PB1), and poly(4‐methyl pentene‐1) (P4MP1) were investigated under both isothermal and nonisothermal conditions using differential scanning calorimetry (DSC). The order of overall crystallization rates under quiescent conditions from fast to slow was found to be: PE, P4MP1, PP and PB1. The Avrami equation was used to analyze isothermal and nonisothermal crystallization processes, respectively. In order to compare relative crystallization rates of these polymers, continuous cooling transformation curves for each polymer under nonisothermal condition as well as the plot of crystallization half‐time as a function of crystallization temperature under isothermal conditions were constructed. Comparisons were made of the relative rate of crystallization of the different isotactic polyolefins with each other and with reports in the literature. Isotactic polyolefins with linear side groups crystallize increasingly more slowly as the side group lengthens with polypentene‐1 (PPT1) and polyhexene‐1 (PH1) crystallizing even more slowly than PB1. It is notable that P4MP1, which has isobutyl as a bulky side group, and apparently poly(3‐methyl butene‐1) (P3MB1) showed fairly high crystallization rates. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007
- 19 June 2007
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 106 (1) , 276-282
Comparative study on quiescent crystallization kinetics of isotactic polyolefins
Quiescent melt crystallization rates of various polyolefins including high density polyethylene (PE), isotactic form of polypropylene (PP), polybutene‐1 (PB1), and poly(4‐methyl pentene‐1) (P4MP1) were investigated under both isothermal and nonisothermal conditions using differential scanning calorimetry (DSC). The order of overall crystallization rates under quiescent conditions from fast to slow was found to be: PE, P4MP1, PP and PB1. The Avrami equation was used to analyze isothermal and nonisothermal crystallization processes, respectively. In order to compare relative crystallization rates of these polymers, continuous cooling transformation curves for each polymer under nonisothermal condition as well as the plot of crystallization half‐time as a function of crystallization temperature under isothermal conditions were constructed. Comparisons were made of the relative rate of crystallization of the different isotactic polyolefins with each other and with reports in the literature. Isotactic polyolefins with linear side groups crystallize increasingly more slowly as the side group lengthens with polypentene‐1 (PPT1) and polyhexene‐1 (PH1) crystallizing even more slowly than PB1. It is notable that P4MP1, which has isobutyl as a bulky side group, and apparently poly(3‐methyl butene‐1) (P3MB1) showed fairly high crystallization rates. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007
- 1 April 2006
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 45 (3) , 317-328
Deformation-Induced Structural Changes in Crystalline Polyolefins
The crystal structures and the hierarchy of structural order in melt crystallized polyolefins are well known. Structural changes that occur at various levels during solid-state deformations of polyolefins have received significant attention only in polyethylene. Studies for other polyolefins have been more limited. This article is divided into separate sections on polyethylene, polyethylene-co-olefin copolymers, isotactic polypropylene, isotactic poly(butene-1), and isotactic poly(4-methylpentene-1). We first discuss in each case the crystal structure of melt crystallized polymers. We then discuss structural changes during solid-state deformations. The differences in the structural changes occurring in the various polyolefins are compared.
- 1 April 2006
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 45 (3) , 317-328
Deformation-Induced Structural Changes in Crystalline Polyolefins
The crystal structures and the hierarchy of structural order in melt crystallized polyolefins are well known. Structural changes that occur at various levels during solid-state deformations of polyolefins have received significant attention only in polyethylene. Studies for other polyolefins have been more limited. This article is divided into separate sections on polyethylene, polyethylene-co-olefin copolymers, isotactic polypropylene, isotactic poly(butene-1), and isotactic poly(4-methylpentene-1). We first discuss in each case the crystal structure of melt crystallized polymers. We then discuss structural changes during solid-state deformations. The differences in the structural changes occurring in the various polyolefins are compared.
- 8 September 2003
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 90 (6) , 1555-1564
Influence of carboxylic acid additives on the flow behavior of molten thermoplastics
Following the suggestions of the behavior of carboxylic acid lubricants between steel surfaces and the wide usage of such acids in polymer compounds, we have considered their influence as an additive in polymer melts. An experimental study of the influence of carboxylic acid additives in various thermoplastics in rheometers is described. Capillary and cone‐plate experiments are reported. A series of polymers of varying polarity, including polyethylene, poly(propylene), polystyrene, poly(methyl methacrylate), and polyamide‐12, are compared. Both aliphatic fatty acids and aromatic carboxylic acids were used as additives. The aliphatic fatty acids include propionic acid, octanoic acid, decanoic acid, dodecanoic acid, tetradecanoic acid, hexadecanoic acid, octadecanoic acid, eicosanoic acid, and commercial stearic acid (mixture of tetradecanoic acid, pentadecanoic acid, hexadecanoic acid, heptadecanoic acid, and octadecanoic acid). The aromatic carboxylic acids include benzoic acid, p‐toluic acid, and 3‐phenylpropionic acid. The greatest effects were found with polyethylene and poly(propylene). Little or no effects were found with the other polymers. Aliphatic fatty acids were more effective than aromatic carboxylic acids. Mechanisms for this behavior are discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1555–1564, 2003
- 8 September 2003
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 90 (6) , 1555-1564
Influence of carboxylic acid additives on the flow behavior of molten thermoplastics
Following the suggestions of the behavior of carboxylic acid lubricants between steel surfaces and the wide usage of such acids in polymer compounds, we have considered their influence as an additive in polymer melts. An experimental study of the influence of carboxylic acid additives in various thermoplastics in rheometers is described. Capillary and cone‐plate experiments are reported. A series of polymers of varying polarity, including polyethylene, poly(propylene), polystyrene, poly(methyl methacrylate), and polyamide‐12, are compared. Both aliphatic fatty acids and aromatic carboxylic acids were used as additives. The aliphatic fatty acids include propionic acid, octanoic acid, decanoic acid, dodecanoic acid, tetradecanoic acid, hexadecanoic acid, octadecanoic acid, eicosanoic acid, and commercial stearic acid (mixture of tetradecanoic acid, pentadecanoic acid, hexadecanoic acid, heptadecanoic acid, and octadecanoic acid). The aromatic carboxylic acids include benzoic acid, p‐toluic acid, and 3‐phenylpropionic acid. The greatest effects were found with polyethylene and poly(propylene). Little or no effects were found with the other polymers. Aliphatic fatty acids were more effective than aromatic carboxylic acids. Mechanisms for this behavior are discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1555–1564, 2003