MRMaria M. Reboredo

Maria M. Reboredo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Maria M. Reboredo has a total of 15 co-authors. Here are the top co-authors by number of shared publications:

  • Mirta I. Aranguren

    Institute of Materials Science and Technology (INTEMA), University of Mar del Plata—National Research Council (CONICET), Av. Juan B. Justo 4302, (7600) Mar del Plata, Argentina

    6 shared publications
  • Betiana A. Acha

    Institute of Materials Science and Technology (INTEMA), University of Mar del Plata, National Research Council (CONICET), Av. Juan B. Justo 4302, 7600 Mar del Plata. Argentina

    2 shared publications
  • N. E. Marcovich

    Chemical Engineering Department, Institute of Materials Science and Technology (INTEMA), University of Mar del Plata, National Research Council (CONICET), B7608FDQ Mar del Plata, Argentina

    2 shared publications
  • Norma E. Marcovich

    Institute of Materials Science and Technology (INTEMA), University of Mar del Plata, National Research Council (CONICET), Av. Juan B. Justo 4302, 7600 Mar del Plata. Argentina

    2 shared publications
  • Norma Esther Marcovich

    Universidad Nacional de Mar del Plata (UNMdP)

    2 shared publications
  • A. N. Ostrovsky

    Department of Chemical Engineering and Department of Materials Engineering, Institute of Research in Materials Science and Technology (INTEMA), Universidad Nacional de Mar del Plata/CONICET, Juan B. Justo 4302 — (7600) Mar del Plata, Argentina

    1 shared publication

Latest Publications

  • Lignin in jute fabric–polypropylene composites

    by B. A. Acha, N. E. Marcovich, M. M. Reboredo

    In this work, the feasibility of using lignin as a compatibilizer for composites made from jute fiber fabric and polypropylene (PP) was studied. Since lignin contains polar (hydroxyl) groups and nonpolar hydrocarbon, it was expected to be able to improve the compatibility between the two components of the composite. It was found that lignin acted as β nucleation, fire retardant, and toughening agent for PP matrix. Jute composites exhibit higher stiffness, tensile strength, and impact behavior in respect to those of neat PP. Although scanning electron micrographic observations indicate that PP‐jute adhesion was slightly improved by lignin addition, additional benefits were only obtained from impact behavior. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009


  • Resin–Sisal and Wood Flour Composites Made from Unsaturated Polyester Thermosets

    by N. E. Marcovich, A. N. Ostrovsky, M. I. Aranguren, M. M. Reboredo

    Short fibers and wood flour were selected as fillers in the production of two types of unsaturated polyester composites (bisphenolic and isophthalic-based thermosets). Sisal fibers were subjected to washing in order to remove the organic coating on the fibers (which were originally prepared for cord manufacture) and to maleic anhydride (MAN) esterification. The effect of these treatments on the thermomechanical properties of the composites, as well as on the mechanical properties (flexural and compression) and water absorption was investigated. All the results are coincident in showing the improved interfacial adhesion obtained by washing and mainly by esterification of the fibers. Additionally, hybrid wood flour sisal composites were prepared and their mechanical properties compared to those of the one-filler composites. The hybrid composites showed improved modulus and maximum stress.


  • Open Access

    Fenómenos de relajación interfacial en compuestos epoxi/aluminio

    by L. Ramajo, M.S. Castro, M.M. Reboredo

    En este trabajo se estudiaron los fenómenos de relajación de materiales compuestos polímero/metal en función de la cantidad de partículas de metálicas incorporadas (aluminio). El concepto de módulo eléctrico fue empleado para analizar los procesos de relajación tipo Debye y Maxwell-Wagner-Sillar, debido a que presenta varias ventajas con respecto al análisis clásico de la parte real (ε') e imaginaria (ε") de la permitividad. El material compuesto se obtuvo por colada y posterior curado a 100ºC por 2 horas, previa mezcla en un mezclador ultrasónico de ambos componentes. La densidad de las muestras se determinó por el método de Arquímedes, mientras que las fracciones en volumen se establecieron mediante termogravimetría. Las mediciones de propiedades dieléctricas se realizaron en el rango de frecuencias de 25Hz a 1Mhz y temperatura de 30 a 120ºC. Por último, la microestructura fue observada mediante Microscopía Electrónica de Barrido. Las micrografías revelaron que la incorporación del metal no incrementó en forma significativa la cantidad de defectos o la porosidad. Los resultados del análisis dieléctrico mostraron que los materiales poseen muy buenas propiedades dieléctricas a bajas temperaturas, y que los fenómenos de relajación son propios de la resina y modificados por la influencia de las cargas metálicas debido a fenómenos de relajación interfacial tipo MWS.

  • Physical and mechanical characterization of jute fabric composites

    by Betiana A. Acha, Norma E. Marcovich, María M. Reboredo

    As‐received and washed jute fabrics were used as reinforcement for a thermoset resin. The mild treatments performed on the jute fabrics did not significantly affect their physical and thermal behaviors. The washed fibers absorbed less water than the unmodified (as received) ones, indicating that the coating used to form the fabrics was hygroscopic. Measurements of the fiber mechanical properties showed a high dispersion due to fiber irregularities, although the values obtained were in agreement with data reported in the literature. These results were also analyzed with the Weibull method. To investigate the effect of the jute treatments on the interface properties, impact, compression, and tensile tests were carried out. The composites made from as‐received jute had the highest impact energy, which was probably associated with weak interfacial adhesion. Composite samples behaved more ductilely in compression than in tensile situations due to the brittle characteristics of the resin used as matrix. The effect of the orientation of the fibers with respect to the direction of the applied force in the different mechanical tests was also studied. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 639–650, 2005


  • Influence of fiber volume fraction and aspect ratio in resol–sisal composites

    by C. N. Zárate, M. I. Aranguren, M. M. Reboredo

    Vegetable fibers are being used as reinforcements in polymeric matrices with a wide variety of applications. Among these fibers, sisal is of particular interest due to the high impact strength and moderate tensile and flexural properties of its derivated composites. Because of its low cost and affinity, a phenol–formaldehyde resin, resol, has been selected as the matrix to obtain resol–sisal composites. The influence of fiber length and volume fraction on flexural properties has been studied. An optimum for the fiber length as well as for the fiber volume fraction was found. The improvement of the properties occurred up to a length of about 23 mm. The use of longer fibers lead to reduced properties because they tended to curl and bend during processing. Besides, actual composite densities were lower than theoretical ones mainly due to the presence of voids. This undesirable porosity produced a reduction in flexural properties at high fiber contents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2714–2722, 2003


  • Composites from PMMA modified thermosets and chemically treated woodflour

    by Betiana A. Acha, Mirta I. Aranguren, Norma E. Marcovich, Maria M. Reboredo

    The mechanical behavior of composites made from woodflour and a modified thermoset unsaturated polyester resin has been examined. Polymethylmethacrylate (PMMA), a common low profile additive (LPA), was used as the matrix modifier. Woodflour, the reinforcing filler, was used ‘as received’ and was also modified with a commercial alkenyl succinic anhydride (ASA), in order to enhance the compatibility with the resin. The composites exhibited higher flexural and compressive modulus and compressive yield stress than the neat resin, while flexural strength and ultimate strain were reduced. The addition of PMMA to the unfilled thermoset led to a LPA morphology and decreased the flexural modulus, but produced an increment in flexural strain at break, impact energy and toughness of the UP resin. No enhancement in the mechanical behavior of the composites was found when treated woodflour instead of unmodified woodflour was used.


  • Mechanical characterization of polypropylene–wood flour composites

    by Adrián J. Nuñez, Pablo C. Sturm, José M. Kenny, M. I. Aranguren, Norma E. Marcovich, María M. Reboredo

    The mechanical performance of different wood flour/polypropylene (PP) composites with interface modifications was compared. Wood flour was incorporated into the matrix after esterification with maleic anhydride (MAN) or without any modification but with the addition of a compatibilizing agent [maleic anhydride–polypropylene copolymer (PPMAN)] to modify the polymer–filler interaction. Composites were prepared by injection molding with different concentrations of wood flour. Mechanical properties (except Young's modulus) were not improved either by the wood flour chemical modification or by the use of PPMAN. However, both compatibilization methods were successful in improving the dispersion of the wood flour in the PP matrix. Creep behavior of composite samples was improved by the addition of PPMAN, whereas the composites prepared from MAN‐treated wood flour showed larger deformations than composites made with untreated particles. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1420–1428, 2003


  • Resol-vegetable fibers composites

    by M. I. Aranguren, M. M. Reboredo, Zárate, C. N.