Florian Flaig
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Florian Flaig has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Marvin Kaufmann
Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM, Bremen, Germany
8 shared publications - Michael Müller
Institute for Acoustics and Dynamics Technische Universitä Langer Kamp 19 38106 Braunschweig Braunschweig Lower Saxony Germany
8 shared publications - Till Vallée
Fraunhofer IFAM
8 shared publications - Holger Fricke
Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM, Bremen, Germany
6 shared publications Lukas Benstem
2 shared publications- Marc Aurel Viehöfer
Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM
2 shared publications
Latest Publications
- Open Access
- 26 June 2026
- Published by Elsevier in Journal of Advanced Joining Processes
- Vol. 14
Towards practical design of adhesive injection processes
- 26 June 2026
- Published by Elsevier in Journal of Advanced Joining Processes
- Vol. 14
Open AccessTowards practical design of adhesive injection processes
- Open Access
- 24 February 2026
- Published by Elsevier in SSRN Electronic Journal
Towards Practical Design of Adhesive Injection Processes
Adhesive injection into thin bond-lines was studied to establish a computationally efficient prediction tool for flow-front evolution, internal velocities and injection pressures. A reduced-order gap-flow approach based on the Partially Filled Gap Model (PFGM) was extended from squeeze-flow to injection by introducing localised inlets, explicit outlets and gravitational body-force contributions for inclined gaps, and was verified against reference problems for source-flow kinematics, conservation of injected volume and gravity-driven redistribution. Experimental validation was performed in a quasi-two-dimensional glass-plate flow cell using a Newtonian silicone-oil model fluid. Several inlet--outlet arrangements and inclinations were investigated, and flow fronts, in-plane velocity fields (Particle Image Velocimetry) and inlet-pressure histories were measured. The simulations reproduced the observed front shapes and filling sequence, captured the main features of the velocity profiles away from inlet and outlet regions, and recovered the characteristic multi-stage pressure evolution. Systematic offsets in absolute pressure level were attributed to additional hydraulic losses in the upstream supply system not represented in the cavity-scale model. The validated model was then applied to a sensitivity analysis and to a frame-like cavity representative of panel-to-frame bonding, demonstrating strong dependences of pressure and injection-induced forces on viscosity, gap height and in-plane dimensions, and illustrating how gravity and boundary layout influence asymmetric filling. Extensions to adhesive-specific rheology, curing, wetting and discrete gas bubbles remain topics for future work.
- 24 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessTowards Practical Design of Adhesive Injection Processes
Adhesive injection into thin bond-lines was studied to establish a computationally efficient prediction tool for flow-front evolution, internal velocities and injection pressures. A reduced-order gap-flow approach based on the Partially Filled Gap Model (PFGM) was extended from squeeze-flow to injection by introducing localised inlets, explicit outlets and gravitational body-force contributions for inclined gaps, and was verified against reference problems for source-flow kinematics, conservation of injected volume and gravity-driven redistribution. Experimental validation was performed in a quasi-two-dimensional glass-plate flow cell using a Newtonian silicone-oil model fluid. Several inlet--outlet arrangements and inclinations were investigated, and flow fronts, in-plane velocity fields (Particle Image Velocimetry) and inlet-pressure histories were measured. The simulations reproduced the observed front shapes and filling sequence, captured the main features of the velocity profiles away from inlet and outlet regions, and recovered the characteristic multi-stage pressure evolution. Systematic offsets in absolute pressure level were attributed to additional hydraulic losses in the upstream supply system not represented in the cavity-scale model. The validated model was then applied to a sensitivity analysis and to a frame-like cavity representative of panel-to-frame bonding, demonstrating strong dependences of pressure and injection-induced forces on viscosity, gap height and in-plane dimensions, and illustrating how gravity and boundary layout influence asymmetric filling. Extensions to adhesive-specific rheology, curing, wetting and discrete gas bubbles remain topics for future work.
- Open Access
- 5 March 2025
- Published by Springer Nature in Applied Intelligence
- Vol. 55 (7) , 1-22
Convolutional neural networks for advanced adhesive joints application patterns
Adhesive bonding is a widely used joining technique across various industries. Achieving uniform adhesive coverage over the entire surface without the formation of air pockets is crucial for creating strong and durable joints. Simultaneously, it is essential to minimise waste caused by material leakage at the edges. However, generating an optimal adhesive pattern to achieve the desired adhesive distribution after compression remains a challenge, as fluids tend to spread in a circular manner, while industry-relevant target geometries are typically non-circular. This paper investigates the application of Convolutional Neural Networks (CNNs) to optimise adhesive application patterns by utilising a simplified simulation model known as the Partially Filled Gaps Model (PFGM) to generate extensive training data. The CNN is trained to predict fluid distribution outcomes based on initial adhesive application patterns and addresses the inverse problem of determining an optimal application pattern to achieve a desired target distribution after compression. Two training approaches are introduced: a basic inverse model that utilizes a straightforward input–output data exchange, and a more advanced strategy that incorporates a forward model to improve accuracy. The forward model predicts the final distribution, enabling better refinement of the initial application patterns. The results demonstrate that the CNN-based approach is highly effective in generating optimal application patterns for adhesive bonds. Its primary advantage, compared to alternative methods, lies in its ability to achieve precise results within a short computation time. However, a significant drawback is the limited flexibility in accommodating variations in parameters.
- 5 March 2025
- Published by Springer Nature in Applied Intelligence
- Vol. 55 (7) , 1-22
Open AccessConvolutional neural networks for advanced adhesive joints application patterns
Adhesive bonding is a widely used joining technique across various industries. Achieving uniform adhesive coverage over the entire surface without the formation of air pockets is crucial for creating strong and durable joints. Simultaneously, it is essential to minimise waste caused by material leakage at the edges. However, generating an optimal adhesive pattern to achieve the desired adhesive distribution after compression remains a challenge, as fluids tend to spread in a circular manner, while industry-relevant target geometries are typically non-circular. This paper investigates the application of Convolutional Neural Networks (CNNs) to optimise adhesive application patterns by utilising a simplified simulation model known as the Partially Filled Gaps Model (PFGM) to generate extensive training data. The CNN is trained to predict fluid distribution outcomes based on initial adhesive application patterns and addresses the inverse problem of determining an optimal application pattern to achieve a desired target distribution after compression. Two training approaches are introduced: a basic inverse model that utilizes a straightforward input–output data exchange, and a more advanced strategy that incorporates a forward model to improve accuracy. The forward model predicts the final distribution, enabling better refinement of the initial application patterns. The results demonstrate that the CNN-based approach is highly effective in generating optimal application patterns for adhesive bonds. Its primary advantage, compared to alternative methods, lies in its ability to achieve precise results within a short computation time. However, a significant drawback is the limited flexibility in accommodating variations in parameters.
- Open Access
- 5 January 2024
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 130
Optimized adhesive application
- 5 January 2024
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 130
Open AccessOptimized adhesive application
- Open Access
- 18 September 2023
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 23 (3)
A practical strategy to identify appropriate application patterns for adhesively bonded joints
This paper presents a simple experimental validation of a method for finding optimal application patterns in adhesive bonding, as previously introduced by Flaig et al. (2023). The study uses two examples to demonstrate that the patterns found in theory effectively fill the target gaps after pressing in practice. The results confirm that the identified application patterns fill the target gaps almost perfectly, ensuring excellent joint integrity after the pressing process. In particular, the applicability of the star pattern to fill square gaps is experimentally validated. In addition, the method of creating a rectangle by pressing a cut star connected by a straight beam is also effective. While the theoretical results in Flaig et al. (2023) were already promising, this research now provides experimental evidence of their practical applicability.
- 18 September 2023
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 23 (3)
Open AccessA practical strategy to identify appropriate application patterns for adhesively bonded joints
This paper presents a simple experimental validation of a method for finding optimal application patterns in adhesive bonding, as previously introduced by Flaig et al. (2023). The study uses two examples to demonstrate that the patterns found in theory effectively fill the target gaps after pressing in practice. The results confirm that the identified application patterns fill the target gaps almost perfectly, ensuring excellent joint integrity after the pressing process. In particular, the applicability of the star pattern to fill square gaps is experimentally validated. In addition, the method of creating a rectangle by pressing a cut star connected by a straight beam is also effective. While the theoretical results in Flaig et al. (2023) were already promising, this research now provides experimental evidence of their practical applicability.
- 1 April 2023
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 124
Do surface pretreatments for adhesives influence the squeeze flow?
- 1 April 2023
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 124
Do surface pretreatments for adhesives influence the squeeze flow?
- 22 December 2022
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 122
How adhesives flow during joining
- 22 December 2022
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 122
How adhesives flow during joining
- 7 September 2021
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (14) , 2295-2324
Experimental validation of a compression flow model of Non-Newtonian adhesives
Currently, adhesive bonding processes are developed and optimised in a time-consuming trial and error procedure, which rarely leads to an optimal solution due to the high complexity of the adhesive flow behaviour during application. The ideal adhesive layer has precise geometric specifications; entrapped air bubbles or overfilling of the bond should be avoided. Numerical methods, such as Computational Fluid Dynamics (CFD), are only capable of calculating squeeze-flow processes to a limited extent. Apart from high computing times, mesh and convergence problems often occur due to the small ratio of adhesive layer thickness to adhesive layer length and width. The Generalised Partially Filled Gap (GPFG) model, published in a companion paper uses fundamental characteristics of every bonding process to derive clever assumptions, and thus provide an efficient simulation tool for adhesive squeeze-flow. The GPFG model simplifies the squeeze-flow to a two-dimensional problem, as the flow in thickness direction can be neglected for most bonding processes – without significant loss of accuracy compared to analytical or CFD solutions. The experimental validation of the model is presented in this study. Both stresses and flow geometry were evaluated, and a very good agreement between experiments and model was proven.
- 7 September 2021
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (14) , 2295-2324
Experimental validation of a compression flow model of Non-Newtonian adhesives
Currently, adhesive bonding processes are developed and optimised in a time-consuming trial and error procedure, which rarely leads to an optimal solution due to the high complexity of the adhesive flow behaviour during application. The ideal adhesive layer has precise geometric specifications; entrapped air bubbles or overfilling of the bond should be avoided. Numerical methods, such as Computational Fluid Dynamics (CFD), are only capable of calculating squeeze-flow processes to a limited extent. Apart from high computing times, mesh and convergence problems often occur due to the small ratio of adhesive layer thickness to adhesive layer length and width. The Generalised Partially Filled Gap (GPFG) model, published in a companion paper uses fundamental characteristics of every bonding process to derive clever assumptions, and thus provide an efficient simulation tool for adhesive squeeze-flow. The GPFG model simplifies the squeeze-flow to a two-dimensional problem, as the flow in thickness direction can be neglected for most bonding processes – without significant loss of accuracy compared to analytical or CFD solutions. The experimental validation of the model is presented in this study. Both stresses and flow geometry were evaluated, and a very good agreement between experiments and model was proven.