William T. Joines
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
William T. Joines has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Kai-Da Xu
School of Information and Communications Engineering, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications - Qing Huo Liu
Eastern Institute of Technology
2 shared publications Joshua Le-Wei Li
Institute of Electromagnetics; University of Electronic Science and Technology of China; Chengdu 611731 China
1 shared publication- William Devereux Palmer
U.S. Army Research Office, NC, USA
1 shared publication Ye Chen
Department of Electrical and Computer Engineering, Duke University, P.O. Box 90291, Durham, NC 27708, USA
1 shared publicationYong Fan
EHF Key Laboratory of Fundamental Science University of Electronic Science and Technology of China Chengdu 611731 People's Republic of China
1 shared publication
Latest Publications
- Open Access
- 1 February 2015
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 9 (3) , 224-229
Microstrip dual‐mode bandpass filter design using pie‐section truncated semi‐circle and quarter‐circle resonators
New dual‐mode microstrip bandpass filters (BPFs) using pie‐section truncated semi‐circle and/or quarter‐circle resonators are presented. The even‐mode and odd‐mode frequency responses of these two resonators are investigated. Compared to the four‐parameter optimisation of the conventional stub‐loaded dual‐mode resonator, only three parameters need to be adjusted and optimised for the proposed resonators. Based on these two novel resonators, three BPF examples are designed, fabricated and tested. In addition, the technique of source‐load cross coupling to improve performance of the filters is adopted. The good agreement between simulated and measured results validates the design concept.
- 1 February 2015
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 9 (3) , 224-229
Open AccessMicrostrip dual‐mode bandpass filter design using pie‐section truncated semi‐circle and quarter‐circle resonators
New dual‐mode microstrip bandpass filters (BPFs) using pie‐section truncated semi‐circle and/or quarter‐circle resonators are presented. The even‐mode and odd‐mode frequency responses of these two resonators are investigated. Compared to the four‐parameter optimisation of the conventional stub‐loaded dual‐mode resonator, only three parameters need to be adjusted and optimised for the proposed resonators. Based on these two novel resonators, three BPF examples are designed, fabricated and tested. In addition, the technique of source‐load cross coupling to improve performance of the filters is adopted. The good agreement between simulated and measured results validates the design concept.
- 24 June 2014
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 56 (9) , 1988-1991
Compact ultra-wideband bandpass filter using quad-T-stub-loaded ring structure
- 24 June 2014
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 56 (9) , 1988-1991
Compact ultra-wideband bandpass filter using quad-T-stub-loaded ring structure
- 9 February 2009
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 51 (4) , 1107-1112
Multisection bandpass filters using capacitively loaded transmission lines
In the frequency range from 50 to 500 MHz, lumped element inductors may have internal resonances, and the distributed nature of the physical structure is solved using transmission‐line theory. Stub filters (shorted or opened stubs separated by sections of line) are quite reliable and easy to manufacture, but their physical size is a disadvantage at these frequencies. In this article, the size reduction process is illustrated by a series of design examples, starting with a bandpass filter at 200 MHz that uses half‐wavelength tapped‐stubs and has multiple resonant sections separated by quarter‐wavelength sections of transmission line. By using this technique the filter area is reduced from 243.67 square inches to 5.99 square inches, an impressive factor of about 40×! Theoretical results are verified by measurements. © 2009 Wiley Periodicals, Inc. Microwave Opt Technol Lett 51: 1107–1112, 2009; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.24252
- 9 February 2009
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 51 (4) , 1107-1112
Multisection bandpass filters using capacitively loaded transmission lines
In the frequency range from 50 to 500 MHz, lumped element inductors may have internal resonances, and the distributed nature of the physical structure is solved using transmission‐line theory. Stub filters (shorted or opened stubs separated by sections of line) are quite reliable and easy to manufacture, but their physical size is a disadvantage at these frequencies. In this article, the size reduction process is illustrated by a series of design examples, starting with a bandpass filter at 200 MHz that uses half‐wavelength tapped‐stubs and has multiple resonant sections separated by quarter‐wavelength sections of transmission line. By using this technique the filter area is reduced from 243.67 square inches to 5.99 square inches, an impressive factor of about 40×! Theoretical results are verified by measurements. © 2009 Wiley Periodicals, Inc. Microwave Opt Technol Lett 51: 1107–1112, 2009; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.24252
- 15 December 2003
- Published by Elsevier in Optics Communications
- Vol. 228 (4-6) , 319-330
Enhanced WDM performance using curved waveguide couplers
- 15 December 2003
- Published by Elsevier in Optics Communications
- Vol. 228 (4-6) , 319-330
Enhanced WDM performance using curved waveguide couplers