Yan-Fei Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yan-Fei Chen has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Hong Zhang
National Engineering Laboratory for Pipeline Safety / Beijing Key Laboratory of Urban Oil and Gas Distribution Technology, China University of Petroleum, Beijing, China
2 shared publicationsJing Cao
CNOOC Research Institute, Beijing, China
2 shared publicationsJing Zhou
State Key Lab of Coastal and Offshore Engineering, Dalian University of Technology, Dalian, China
2 shared publicationsJuan Zhang
HydroChina Beijing Engineering Corporation, Beijing, China
2 shared publicationsXin Li
State Key Lab of Coastal and Offshore Engineering, Dalian University of Technology, Dalian, China
2 shared publicationsChuan Ao
School of Mechanical and Transportation Engineering, China University of Petroleum, Beijing, China
1 shared publication
Latest Publications
- 10 September 2021
- Published by Springer Nature in China Ocean Engineering
- Vol. 35 (4) , 544-553
Flapwise Bending Vibration Analysis of Rotating Tapered Rayleigh Beams for the Application of Offshore Wind Turbine Blades
- 10 September 2021
- Published by Springer Nature in China Ocean Engineering
- Vol. 35 (4) , 544-553
Flapwise Bending Vibration Analysis of Rotating Tapered Rayleigh Beams for the Application of Offshore Wind Turbine Blades
- 1 April 2016
- Published by Springer Nature in China Ocean Engineering
- Vol. 30 (2) , 231-241
Ultimate bending capacity of strain hardening steel pipes
- 1 April 2016
- Published by Springer Nature in China Ocean Engineering
- Vol. 30 (2) , 231-241
Ultimate bending capacity of strain hardening steel pipes
- 11 April 2015
- Published by Springer Nature in China Ocean Engineering
- Vol. 29 (2) , 241-252
Ultimate load capacity of offshore pipeline with arbitrary shape corrosion defects
- 11 April 2015
- Published by Springer Nature in China Ocean Engineering
- Vol. 29 (2) , 241-252
Ultimate load capacity of offshore pipeline with arbitrary shape corrosion defects
- 11 March 2010
- Published by American Society of Civil Engineers (ASCE)
- p. 3328-3344
Plastic Interaction Relations for Corroded Steel Pipes under Combined Loadings
Interaction relationships can be derived analytically for corroded pipelines under combined loadings, assuming a fully plastic failure mode. A set of closed-form analytical solutions are presented in this paper, describing the interaction relationships between bending resistance, axial force and internal pressure for corroded pipelines. Three different idealized corrosion shapes, namely a constant-depth, an elliptical and a parabolic corrosion shapes, are considered and compared. The presence and shape of corrosion features reduces the ultimate bending capacity significantly, having analyzed the outcome of analytical calculations performed, using the interaction relationships as derived for corroded pipelines under bending, axial force and internal pressure. Good agreement is furthermore observed comparing the calculated bending moment capacity using the interaction curves with the actually measured bending moment from full-size tests performed on corroded pipes. It is shown that pipelines having corrosion features having an (idealized) elliptical or parabolic shapes yield higher plastic bending resistance when compared with a constant-depth corrosion feature. It is further pointed out that the simplification of the actual corrosion geometry by a constant-depth approximation, as commonly assumed in current assessment codes for corroded pipes, will inevitably underestimate the residual plastic strength of the pipe, especially for deep and wide corrosion features.
- 11 March 2010
- Published by American Society of Civil Engineers (ASCE)
- p. 3328-3344
Plastic Interaction Relations for Corroded Steel Pipes under Combined Loadings
Interaction relationships can be derived analytically for corroded pipelines under combined loadings, assuming a fully plastic failure mode. A set of closed-form analytical solutions are presented in this paper, describing the interaction relationships between bending resistance, axial force and internal pressure for corroded pipelines. Three different idealized corrosion shapes, namely a constant-depth, an elliptical and a parabolic corrosion shapes, are considered and compared. The presence and shape of corrosion features reduces the ultimate bending capacity significantly, having analyzed the outcome of analytical calculations performed, using the interaction relationships as derived for corroded pipelines under bending, axial force and internal pressure. Good agreement is furthermore observed comparing the calculated bending moment capacity using the interaction curves with the actually measured bending moment from full-size tests performed on corroded pipes. It is shown that pipelines having corrosion features having an (idealized) elliptical or parabolic shapes yield higher plastic bending resistance when compared with a constant-depth corrosion feature. It is further pointed out that the simplification of the actual corrosion geometry by a constant-depth approximation, as commonly assumed in current assessment codes for corroded pipes, will inevitably underestimate the residual plastic strength of the pipe, especially for deep and wide corrosion features.