XLXinghan Li

Xinghan Li

*This is an algorithmically generated author record based on publicly available information.

Xinghan Li has a total of 18 co-authors. Here are the top co-authors by number of shared publications:

  • Wenxiu Zhang

    Chinese Academy of Sciences, Institute of Geology and Geophysics, Beijing, China

    5 shared publications
  • Hong Li

    CAS Engineering Laboratory for Deep Resources Equipment and Technology, Institute of Geology and Geophysics, Chinese Academy of Sciences , Beijing, 100029 , China

    2 shared publications
  • Jian Zheng

    CAS Engineering Laboratory for Deep Resources Equipment and Technology, Institute of Geology and Geophysics, Chinese Academy of Sciences , Beijing, 100029 , China

    2 shared publications
  • Jianbao Fan

    CAS Engineering Laboratory for Deep Resources Equipment and Technology, Institute of Geology and Geophysics, Chinese Academy of Sciences, Beijing 100029, China

    2 shared publications
  • Pengfei Liang

    CAS Engineering Laboratory for Deep Resources Equipment and Technology, Institute of Geology and Geophysics, Chinese Academy of Sciences, Beijing, China

    2 shared publications
  • Wenxuan Chen

    CAS Engineering Laboratory for Deep Resources Equipment and Technology, Institute of Geology and Geophysics, Chinese Academy of Sciences , Beijing, 100029 , China

    2 shared publications

Latest Publications

  • Open Access

    Calibration method of azimuth electromagnetic boundary detection logging while drilling based on air–seawater double-layer dielectric as reflection interface

    by Xinghan Li, Wenxiu Zhang, Peng Chen, Wenxuan Chen, Jun Wang, Jian Zheng, Jiaqi You, Yali Zhang, Hong Li

    An azimuth electromagnetic propagation logging while drilling tool provides the electrical parameters around a well in the intelligent drilling guidance system. It is a key link in intelligent guidance technology. As the stratum directivity parameter, the azimuth signal is associated with the compensation measurement of the resistivity instrument, which guides the drilling. However, it must be calibrated to have physical significance. The traditional method uses a water tank for calibration. However, this method is affected by the edge effect, which greatly weakens the azimuth signal. The model is complex and difficult to recover, which seriously suppresses the calibration results and causes errors in the azimuth signal. To eliminate the edge effect and simplify the model to improve the signal quality, an instrument calibration method based on sea level as the reflection interface is proposed in this paper. The air–seawater structure can simplify the calculation model, eliminate the edge effect and improve the signal strength. According to 1D air–seawater model simulation and 3D water tank model calculation, the feasibility of the simplified model is analyzed. According to the azimuth signal characteristics of the simplified model, an azimuth signal correction process that is more suitable for azimuth electromagnetic propagation logging while drilling is proposed. The measured data show that the air–seawater model improves the signal-to-noise ratio of the azimuth signal, verifies the detection ability of the azimuth antenna and provides technical support for oil and gas development in complex reservoirs.


  • Open Access

    Electromagnetic propagation logging while drilling data acquisition method based on undersampling technology

    by Xinghan Li, Wenxiu Zhang, Wenxuan Chen, Yali Zhang, Jian Zheng, Jianbao Fan, Hong Li, Zhenjun Ma

    With the development of complex and unconventional reservoirs, oil and gas exploration becomes increasingly difficult. Highly deviated wells/horizontal wells are widely used. The electromagnetic propagation logging while drilling (LWD) is more effective in complex geological environment detection owing to geological orientation and real-time formation evaluation. However, its operating frequency is generally at the MHz level. Traditional acquisition techniques require an analogue to digital converter with high sampling rates, which will introduce complex circuit structures and increase sampling costs. The undersampling technology has overcome these disadvantages. The difficulties in the undersampling technology include the selection of an undersampling frequency and the acquisition of a signal correction coefficient. The range of undersampling frequencies and a correction coefficient has been developed to process the electromagnetic propagation LWD measurements in this paper. The range of undersampling frequency ensures the validity of the sampled data. The correction coefficient ensures that different frequency signals use the same undersampling frequency to obtain the same frequency recovery signal. The correctness of these parameters is verified by simulation and field data examples. The range of undersampling frequency and a correction coefficient has been applied, improving the data stability and providing reliable technical support for the exploration and development of unconventional oil and gas.


  • Electric and magnetic dipole antennas of a directional resistivity logging-while-drilling tool for “look-around” boundary detection

    by Jianbao Fan, Wenxiu Zhang, Wenxuan Chen, Xinghan Li, Pengfei Liang

    Directional resistivity logging-while-drilling tools play an important role in geosteering. In contrast to the widely used tool with magnetic dipole transmitters and receivers, tools are investigated with electric and magnetic dipoles as transmitters and/or receivers for “look-around” boundary detection. Measurement schemes are selected based on their look-around boundary detection abilities. Those measurement schemes are studied regarding the sensitivity and depths of boundary detection, the optimal transmitter-receiver distance and frequency, and the effects of a drill collar using the coefficient propagator method and the finite-difference method. Higher sensitivity to a boundary often implies a shallower depth of investigation. More specifically, the measurement schemes using an electric dipole transmitter and receiver are the least sensitive to the boundary; however, such schemes have the maximum depth of detection and the strongest signal strength. The schemes using electric and magnetic dipole transmitters and receivers have a moderate depth of detection and signal strength. The measurement schemes with a magnetic dipole transmitter and receiver have the highest sensitivity to the boundary and the weakest signal strength. The drill collar affects the response of all of the measurement schemes. However, this effect cannot be corrected with a simple coefficient for the schemes using an axial electric dipole transmitter, but it can be corrected for others. The optimal frequencies and optimal transmitter-receiver distances of those schemes have two types: the changing one that changes with the distance to boundaries and the fixed one that usually has the lowest frequency or the shortest transmitter-receiver distance. The characteristics of each measurement scheme will guide the tool designs and determine its role in the application and method of interpretation.