Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zhuoyue Li has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Slurry Thickness on the Quality of Aluminized Coatings

    by Zhuoyue Li, Cheng Wang, Xiangyu Ding, Xin Li, Jiabo Yu, Qiuliang Li, Yi Qu

    Diffusion aluminum coating is crucial to protect aero-engine turbine blades from high-temperature oxidation. Slurry aluminizing, as a commonly-used coating preparation technology, has variations in the process parameters that directly affect the quality of the coating. Therefore, this paper investigates the effect of slurry thickness on coating quality. Different forms of aluminized coatings were obtained by coating nine DZ22B nickel-based superalloy plates of the same size with different slurry thicknesses while keeping other parameters constant. These aluminized coatings were characterized using a scanning electron microscope (SEM) with an energy dispersive spectrometer (EDS), an X-ray diffractometer (XRD), and a surface gauge. The results show that the AlNi phase dominates the matrix of the aluminized coating, and the outer layer of the coating has white dotted precipitates of Cr. As the slurry thickness increases, the coating thickness increases, and the proportion of the outer layer in the overall coating increases. In contrast, the thickness of the interdiffusion layer does not change significantly. The thicker the slurry, the higher the Al content of the coating surface. A medium-thickness slurry can form a smooth aluminizing coating with a roughness Ra < 4.5 μm surface. The combined results show that a medium-thick slurry can produce a high-quality coating.


  • Open Access

    Comparative Study on the Surface Remelting of Mo-Si-B Alloys with Laser and Electron Beam

    by Qiuliang Li, Cheng Wang, Zhuoyue Li, Yi Qu, Xiangrong Li

    The Mo-12Si-8.5B alloy was surface-remelted by laser and electron beam, and the microstructure of its melt pool and substrate regions were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy spectrometry (EDS) techniques. It was found that the composition of the surface phases in the Mo-12Si-8.5B alloy did not change by the high-energy beam surface remelting process, but the microstructure of the molten pool region was significantly different from that of the substrate region, and its phase distribution was more uniform. Dendrites appeared on the surface of the material under the action of both processes, and the Si- and B-rich phases were mainly gathered in the interdendritic region. In the melt pool of the laser-remelted specimens, the α-Mo phase was continuously distributed with an average dendrite length of 70 µm, while the α-Mo phase distribution in the melt pool of the electron beam remelted specimens were relatively concentrated, with a larger dendrite size and an average dendrite length of 120 µm. The dendrite size in the melt pool of the laser remelted material was smaller, and the distribution of the elements was relatively uniform. Using a laser beam as the heat source was more favorable for the next step of the additive manufacturing of the core parts of hypersonic vehicles.


  • Open Access

    Surface Defect Detection Model for Aero-Engine Components Based on Improved YOLOv5

    by Xin Li, Cheng Wang, Haijuan Ju, Zhuoyue Li

    Aiming at the problems of low efficiency and poor accuracy in conventional surface defect detection methods for aero-engine components, a surface defect detection model based on an improved YOLOv5 object detection algorithm is proposed in this paper. First, a k-means clustering algorithm was used to recalculate the parameters of the preset anchors to make them match the samples better. Then, an ECA-Net attention mechanism was added at the end of the backbone network to make the model pay more attention to feature extraction from defect areas. Finally, the PANet structure of the neck network was improved through its replacement with BiFPN modules to fully integrate the features of all scales. The results showed that the mAP of the YOLOv5s-KEB model was 98.3%, which was 1.0% higher than the original YOLOv5s model, and the average inference time for a single image was 2.6 ms, which was 10.3% lower than the original model. Moreover, compared with the Faster R-CNN, YOLOv3, YOLOv4 and YOLOv4-tiny object detection algorithms, the YOLOv5s-KEB model has the highest accuracy and the smallest size, which make it very efficient and convenient for practical applications.


  • Open Access

    Prediction Model of Aluminized Coating Thicknesses Based on Monte Carlo Simulation by X-ray Fluorescence

    by Zhuoyue Li, Cheng Wang, Haijuan Ju, Xiangrong Li, Yi Qu, Jiabo Yu

    An aluminized coating can improve the high-temperature oxidation resistance of turbine blades, but the inter-diffusion of elements renders the coating’s thickness difficult to achieve in non-destructive testing. As a typical method for coating thickness inspection, X-ray fluorescence mainly includes the fundamental parameter method and the empirical coefficient method. The fundamental parameter method has low accuracy for such complex coatings, while it is difficult to provide sufficient reference samples for the empirical coefficient method. To achieve accurate non-destructive testing of aluminized coating thickness, we analyzed the coating system of aluminized blades, simulated the spectra of reference samples using the open-source software XMI-MSIM, established the mapping between elemental spectral intensity and coating thickness based on partial least squares and back-propagation neural networks, and validated the model with actual samples. The experimental results show that the model’s prediction error based on the back-propagation neural network is 4.45% for the Al-rich layer and 16.89% for the Al-poor layer. Therefore, the model is more suitable for predicting aluminized coating thickness. Furthermore, the Monte Carlo simulation method can provide a new way of thinking for materials that have difficulty in fabricating reference samples.


  • Open Access

    Plasma Oscillatory Pressure Sintering of Mo-9Si-8B Alloy with ZrB2 Addition

    by Xiangyu Ding, Zhenping Guo, Xiangrong Li, Zhuoyue Li, Xin Li

    Oscillatory pressure sintering is a novel crystal refinement technology. The doping of different concentrations of ZrB2 under oscillatory sintering technology (9 Hz) is discussed here, focusing on its macroscopic mechanics and oxidation resistance. In particular, doping 2.5 wt% ZrB2 can effectively increase the hardness of the alloy, slightly increase the fracture toughness of the alloy and have an outstanding effect on the oxidation resistance of the alloy at 1300 °C, achieving the effect of reducing mass loss by 80.3%.


  • Open Access

    Study on the Pre-Oxidation and Resulting Oxidation Mechanism and Kinetics of Mo-9Si-8B Alloy

    by Cheng Wang, Qiuliang Li, Zhenping Guo, Xiangrong Li, Xiangyu Ding, Xin Li, Zhuoyue Li, Bin Li

    Molybdenum silicon boron alloy is regarded as the next generation of superalloy that is expected to replace nickel-based superalloys. However, the high-temperature oxidation resistance of Mo-Si-B alloy has always been an issue worth studying. In this study, Mo-9Si-8B alloy was prepared via a plasma oscillatory pressure sintering process and pre-oxidized at 1300 °C while maintaining a certain balance of mechanical and oxidation properties. The influence of the oxide protective layer on its performance at high temperature of 1150 °C was explored, the micro-mechanism of its performance and its failure mode of the hinge-locking mechanism was illustrated, and finally, its oxidation kinetics was inferred. In conclusion, pre-oxidized Mo-9Si-8B (at.%) alloy did play a role in delaying the oxidation process during the initial period of cyclic oxidation. However, with the increase of cyclic oxidation time, the improvement of high-temperature oxidation resistance was limited.