Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Amrit Prasad Kafle has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    An Artificial Hybrid PEO - nano Si3N4 Composite SEI for Stable Sodium Metal Batteries

    by Sukanya Goswami, Roya Damircheli, Amrit Prasad Kafle, Emily Cheng, Binh Hoang, Chuan-Fu Lin

    Sodium-based batteries have emerged as a promising alternative to lithium-ion systems owing to the natural abundance and low cost of sodium resources. However, unstable native SEIs limit the practical deployment of sodium metal anodes. This fragile and heterogeneous interphase causes dendrite growth, electrolyte consumption, and premature cell failure during sodium plating and stripping. In this work, we developed a hybrid organic-inorganic artificial SEI via drop-casting of a poly (ethylene oxide) (PEO) and nano-silicon nitride (Si3N4) composite onto sodium metal discs. The design combines PEO's flexibility with nano-Si3N4 derived inorganic species to form a protective interface. Five distinct post-deposition drying protocols were systematically evaluated to determine how processing conditions affect coating morphology and electrochemical performance. Galvanostatic cycling, electrochemical impedance spectroscopy (EIS), field-emission scanning electron microscopy (FESEM), and X-ray diffraction (XRD) were used to evaluate the electrochemical behavior, interfacial evolution, and structural characteristics of each coating variant. The air-dried hybrid coating sustained stable cycling beyond 3000 hours at 0.25 mA cm-2 and remained stable beyond 1500 hours at 0.5 mA cm-2 while all alternative post-treatment variants failed earlier but significantly improved from bare sodium. This work highlights the effectiveness of the hybrid PEO-nano Si3N4 composite SEI for stablizing sodium metal.

  • Open Access

    High Stack Pressure Tolerable Sulfide Glass – Polymer Composite Solid-State Electrolyte

    by Sneha Perikkathra, Amrit Prasad Kafle, Binh Hoang, Roya Damircheli, Sukanya Goswami, Chuan-Fu Lin

    Highly ion-conductive solid electrolytes often suffer from degradation under high stack pressures. Therefore, glass-polymer composite electrolytes are promising candidates for next-generation solid-state batteries due to the combination of high ionic conductivity of sulfide glass and mechanical flexibility of polymer electrolytes. In this work, we prepared a composite electrolyte using PEO and LiTFSI as the polymer-salt matrix for the 60Li₂S–32SiS₂–8P₂S₅ (LSP) glass particles, with polymer-to-glass (P – G) ratios of (100-X) P – (X) G, where X = 0, 30, 50, 70, 90, and 100. The composite mixture powder was pressed by isostatic cold pressing inside an Ar-filled glove box to obtain pellets. The structural characterization with X-ray powder diffraction and Raman spectroscopy confirmed the amorphous nature of the composite. Through controlling the ratios between polymer and glass electrolytes in the composites, optimized ionic conductivity and stack pressure tolerance is achieved. At room temperature, small amounts of polymer electrolyte in the composite solid-state electrolyte, namely 30P-70G, boost mechanical tolerance by ~ 3x and maintain high ionic conductivity, 0.32~0.45 mS/cm at room temperature. At high temperature, the composite with a larger amount of polymer electrolyte, namely 70P-30G, exhibits both high conductivity and mechanical tolerance, given the maximum ionic conductivity of 2.95 mS/cm at 55°C with a maximum stack pressure of 9.78 MPa. The results show that polymer-glass composite electrolytes provide improved pressure tolerance and resilience while maintaining high ionic conductivity. Our findings emphasize the potential of glass LSP–PEO composite electrolytes for mechanically resilient solid-state batteries operating under elevated temperature conditions.

  • Synergistic Hybrid Interfaces for Ultrastable Sodium Anode via Spontaneous Conversion of Tin Fluoride in Polymer Matrix

    by Roya Damircheli, David Murdock Stewart, Amrit Prasad Kafle, Tanmay Sarkar Akash, Binh Hoang, Sukanya Goswami, Tai-Feng Hung, Siddhartha Das, Chuan-Fu Lin


  • Open Access

    The Mixed Halogen-Ion Effect in Lead Silicate Glasses: A Correlative Study of Ionic Transport and Optical Spectroscopy in the 45PbO–xPbF2–(20−x)PbCl2–35SiO2 System

    by Manar Alenezi, Amrit Prasad Kafle, Meznh Alsubaie, Najwa Albalawi, Ian L. Pegg, Biprodas Dutta

    We present a fresh perspective on the mixed halogen-ion effect (MHE) in lead silicate glasses containing a mixture of halogen ions with a correlative study of optical spectroscopy and halogen ion transport. PbO was partially substituted by either PbCl2 or PbF2 in the ternary glass system: (65 − x) − x(PbF2 or PbCl2)-35SiO2 (where 0 ≤ x ≤ 20 mol%) and by a mixture of PbF2 and PbCl2 in the quaternary glass series: 45PbO − xPbF2 − (20 − x)PbCl2–35SiO2 (where 0 ≤ x ≤ 20 mol%). A suite of improved characterization techniques, including 4-probe van der Pauw resistivity measurements, optical absorption spectroscopy, differential thermal analysis, etc., was employed to correlate composition with physical properties. Replacing PbO with small quantities of PbF2 or PbCl2 in binary 65PbO-35SiO2 glass resulted in a dramatic increase in conductivity by 3–4 orders of magnitude, confirming a shift from Pb2+-mediated to halide ion-mediated conduction and, within the mixed-halogen series, a profound MHE was observed. Contrary to previously reported data, the activation energy for conduction and the resistivity both exhibited maxima at the mixed halogen-ion ratio, MHR = (F/(F + Cl), of 0.5. The glass transition temperature (Tg) exhibited a non-monotonic trend, peaking at 506 °C for the MHR = 0.5 composition. Optical absorption measurements have revealed that the MHR = 0.5 glass has the broadest absorption edge and also exhibits certain features in the near IR region of the Urbach tail, which are suggestive of maximum electronic disorder.


  • Open Access

    Mixed Polaron and Bipolaron Transport in (xV2O5–(65–x) Sb2O3–35P2O5) Glasses

    by Manar Alenezi, Amrit Prasad Kafle, Meznh Alsubaie, Ian L. Pegg, Najwa Albalawi, Biprodas Dutta

    This study presents the electrical and optical properties of 35P2O5–xV2O5–(65–x) Sb2O3 glasses for 0 ≤ x ≤ 65 mol%. The direct current (DC) resistivity was measured by the Van der Pauw method and optical absorption spectra were taken in the Ultraviolet–Visible-Near-Infrared (UV–VIS–NIR) range. Electrical transport is attributed to simultaneous hopping of small polarons (SPs) between V4+ and V5+ (vanadium ion) sites and small bipolarons (SBPs) between the Sb3+ and Sb5+ (antimony ion) sites. The resistivity exhibits a non-linear dependence on the ionic fraction of vanadium (nv), whereas the resistivity exhibits a minimum in the composition range 0 ≤ nV ≤ 0.3, and a resistivity maximum was observed in the range 0.3 ≤ nV ≤ 0.5. On further increasing nv, the resistivity exhibits a monotonic decline. In the composition range 0 ≤ nV ≤ 0.3, where the hopping distance between V ions decreases, while that between the Sb ions increases, the resistivity minimum has been shown to be the consequence of decreasing tunneling distance of SPs between the V4+ and V5+ ion sites. In the composition range 0.3 ≤ nV ≤ 0.5, the resistivity, activation energy for DC conduction, glass transition temperature, and density exhibit their respective maxima even though the separation between the V4+ and V5+ sites continues to decrease. This feature is explained by enhanced localization of electrons on account of increased disorder (entropy) among the SPs and SBPs, like that of Anderson localization. This argument is further supported by a shift in the polaronic optical absorption bands associated with the SPs and SBPs toward higher energies. The transport behavior of all the glasses except the x = 0 composition has been explained by adiabatic transport, principally, by the SPs on V ions while the Sb ions contribute little to the total transport process. The results provide a clear relation between composition, polaron/bipolaron contributions, and conduction in these glasses.


  • Open Access

    Mixed Polaron and Bipolaron Transport in (xV2O5 – (65-x) Sb2O3 – 35P2O5) Glasses

    by Manar Alenezi, Amrit Prasad Kafle, Meznh Alsubaie, Ian L. Pegg, Najwa Albalawi, Biprodas Dutta

    This study presents the electrical and optical properties of phosphate glasses in the 35P2O5 -xV2O5 -(65–x) Sb2O3 (PVS) system with 0 ≤ x ≤ 65 mol%. DC resistivity was measured using the Van der Pauw method and optical absorption spectra were recorded in the UV–VIS–NIR range. Electrical transport is attributed to simultaneous hopping of small polarons (SPs) between V4+ and V5+ (vanadium ion) sites and small bipolarons (SBPs) between Sb3+ and Sb5+ (antimony ion) sites. The resistivity exhibits a non- linear dependence on the ionic fraction of vanadium, defined as, [V]([V]+[Sb]) where [V] and [Sb] are the concentrations of the respective cations in the glasses. Whereas the resistivity exhibits a minimum in the composition range 0 ≤ nV ≤ 0.3, a resistivity maximum was observed in the range 0.3 ≤ nV ≤ 0.5. On further increasing nv, the resistivity exhibits a monotonic decline. In the composition range 0 ≤ nV ≤ 0.3, where the hopping distance between V ions decreases, while that between the Sb ions increases, the resistivity minimum has been shown to be the consequence of decreasing tunneling distance of SPs between the V4+ and V5+ ion sites. Though the probability of successful hops of SBPs decreases on account of increasing separation between Sb3+ and Sb5+ ions, the far superior mobility of SPs than that of SBPs more than offsets the decreasing contribution of SBPs to the total conductivity. In the composition range 0.3 ≤ nV ≤ 0.5, the resistivity, activation energy for DC conduction, glass transition temperature and also density exhibit their respective maxima even though the separation between V4+ and V5+ sites continues to decrease. This feature is explained by enhanced localization of electrons on account of increased disorder (entropy) among the SPs and SBPs, similar to that of Anderson localization. This argument is further supported by a shift of the polaronic optical absorption bands associated with the SPs and SBPs toward higher energies. The transport behavior of all the glasses except the x = 0 composition has been explained by adiabatic transport, principally, by the SPs on V ions while the Sb ions contribute little to the total transport process. On the contrary, Sb ions is the principal source that produces the highly disordered potential field leading to a resistivity maximum at a [V/Sb] ratio of ~ 0.5 in the glass composition.

  • Open Access

    Raman Spectroscopy and Electrical Transport in 30Li2O• (67−x) B2O3•(x) SiO2•3Al2O3 Glasses

    by Amrit P. Kafle, David McKeown, Winnie Wong-Ng, Meznh Alsubaie, Manar Alenezi, Ian L. Pegg, Biprodas Dutta

    We have investigated the influence of the relative proportions of glass formers in a series of lithium alumino-borosilicate glasses with respect to electrical conductivity (σ) and glass transition temperature (Tg) as functions of glass structure, as determined using Raman spectroscopy. The ternary lithium alumino-borate glass exhibits the highest σ and lowest Tg among all the compositions of the glass series, 30Li2O•3Al2O3• (67−x) B2O3•xSiO2. However, as B2O3 is replaced by SiO2, a shallow minimum in σ, as well as a shallow maximum in Tg, are observed near x = 27, where the Raman spectra indicate that isolated diborate/tetraborate/orthoborate groups are being progressively replaced by danburite/reedmergnerite-like borosilicate network units. Overall, as the glasses become silica-rich, σ is minimized, while Tg is maximized. In general, these findings show correlations among Tg (sensitive to network polymerization), σ (proportional to ionic mobility), and the different borate and silicate glass structural units as determined using Raman spectroscopy.


  • Open Access

    Crystal chemistry and ionic conductivity of garnet-type solid-state electrolyte, Li 5- x La 3 (NbTa)O 12- y

    by Amrit P. Kafle, Winnie Wong-Ng, Vladimir Oleshko, Gery R. Stafford, James A. Kaduk, Andreza Eufrasio, Ian L. Pegg, Biprodas Dutta

    Crystal structures, microtopography, morphologies, elemental compositions, and ionic conductivity have been investigated for Li 5- x La 3 (Nb,Ta)O 12- y using X-ray diffraction (XRD), field-emission analytical scanning and transmission electron microscopies (S/TEM), and electrochemical impedance spectroscopy. Using Rietveld refinements with powder XRD patterns, we determined that the number of Li atoms in the formula is less than 5 and that Li 5- x La 3 (NbTa)O 12- y crystallizes in the cubic garnet structure with a space group Ia- 3 d . Sintering at varying temperatures (750–1000 °C) for 5 h in an ambient atmosphere produced distinct outcomes. Rietveld refinements disclosed that the sample sintered at 1000 °C (Li 3.43(2) La 3 Nb 1.07(2) Ta 0.93(2) O 12- y , a = 12.8361(7) Å, V = 2114.96(3) Å3) exhibited the highest ionic conductivity, while the 850 °C sample had the lowest conductivity, characterized by lower Li concentration and impurity phases (Li(Nb,Ta) 3 O 88 , Li 2 CO 3 ). Analyses, including XRD and electron microscopy, confirmed the 1000 °C sample as a relatively phase pure with enhanced Li content (Li/La = 1.2), larger grains (15 μm), and uniform crystallinity. The 1000 °C sample introduced additional partially filled Li3 (96 h ) sites, promoting Li migration, and enhancing ionic conductivity. The resulting XRD pattern at 1000 °C has been submitted to the Powder Diffraction File as a reference.


  • Open Access

    Raman Spectroscopy and Electrical Transport in 30Li2O• (67-X) B2O3•(x) SiO2•3Al2O3 Glasses

    by Amrit P. Kafle, David McKeown, Winnie Wong-Ng, Meznh Alsubaie, Manar Alenezi, Ian L Pegg, Biprodas Dutta

    We have investigated the influence of the relative proportions of glass formers in a series of lithium alumino-borosilicate glasses with respect to electrical conductivity () and glass transition temperature (Tg) as functions of glass structure, as determined by Raman spectroscopy. The ternary lithium alumino-borate glass exhibits the highest  and lowest Tg among all the compositions of the glass series, 30Li2O•3Al2O3• (67-x) B2O3•xSiO2. However, as B2O3 is replaced by SiO2, a shallow minimum in  as well as a shallow maximum in Tg are observed near x = 27, where the Raman spectra indicate isolated diborate/tetraborate/orthoborate groups are being progressively replaced by danburite/reedmergnerite-like borosilicate network units. Overall, as the glasses become silica-rich,  is minimized, while Tg is maximized. In general, these findings show correlations among Tg, (sensitive to network polymerization),  (proportional to ionic mobility), and the different borate and silicate glass structural units as determined by Raman spectroscopy. X-ray diffraction analyses demonstrate the absence of appreciable crystallinity in the glasses investigated. However, scanning electron microscopy (SEM) images of HF-etched samples showed that glasses, and especially the borate-rich compositions comprise two distinct glassy phases. The isolated phase is 25-100 nm in diameter, dispersed evenly in a glassy matrix.