Patimapon Sukmak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Patimapon Sukmak has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Suksun Horpibulsuk
Suranaree Univ. of Technology
4 shared publications - Arul Arulrajah
Professor, Dept. of Civil and Construction Engineering, Swinburne Univ. of Technology, Melbourne, VIC 3122, Australia. ORCID:
2 shared publications Gampanart Sukmak
2 shared publications- Gampanart Sukmak
School of Engineering, Technology and Center of Excellence in Sustainable Disaster Management, Walailak University, Nakhonsithammarat 80161, Thailand
2 shared publications - Andrei Victor Sandu
Academy of Romanian Scientists (AOSR), 54 Splaiul Independentei St., Sect. 5, 050094 Bucharest, Romania
1 shared publication Annan Zhou
1 shared publication
Latest Publications
- Open Access
- 5 October 2024
- Published by Elsevier in Developments in the Built Environment
- Vol. 20
Mechanical and microstructural properties of cement-stabilized soft clay improved by sand replacement and biochar additive for subgrade applications
- 5 October 2024
- Published by Elsevier in Developments in the Built Environment
- Vol. 20
Open AccessMechanical and microstructural properties of cement-stabilized soft clay improved by sand replacement and biochar additive for subgrade applications
- Open Access
- 18 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2643
Alkaline-Activation Technique to Produce Low-Temperature Sintering Activated-HAp Ceramic
The fabrication of hydroxyapatite (HAp) ceramics prepared by existing conventional sintering requires high-temperature sintering of 1250 °C to 1300 °C. In this paper, the activated metakaolin (MK)/HAp specimens were prepared from varied mix design inputs, which were varied solid mixtures (different amounts of MK loading in HAp) and liquid-to-solid (L/S) ratios, before being pressed and sintered at 900 °C. Phase analysis, thermal analysis, surface morphology, and tensile strength of the specimens were investigated to study the influences of the Al, Si, Fe, Na, and K composition on the formation of the hydroxyapatite phase and its tensile strength. XRD analysis results show the formation of different phases was obtained from the different mix design inputs HAp (hexagonal and monoclinic), calcium phosphate, sodium calcium phosphate silicate and calcium hydrogen phosphate hydrate. Interestingly, the specimen with the addition of 30 g MK prepared at a 1.25 L/S ratio showed the formation of a monoclinic hydroxyapatite phase, resulting in the highest diametrical tensile strength of 12.52 MPa. Moreover, the increment in the MK amount in the specimens promotes better densification when sintered at 900 °C, which was highlighted in the microstructure study. This may be attributed to the Fe2O3, Na2O, and K2O contents in the MK and alkaline activator, which acted as a self-fluxing agent and contributed to the lower sintering temperature. Therefore, the research revealed that the addition of MK in the activated-HAp system could achieve a stable hydroxyapatite phase and better tensile strength at a low sintering temperature.
- 18 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2643
Open AccessAlkaline-Activation Technique to Produce Low-Temperature Sintering Activated-HAp Ceramic
The fabrication of hydroxyapatite (HAp) ceramics prepared by existing conventional sintering requires high-temperature sintering of 1250 °C to 1300 °C. In this paper, the activated metakaolin (MK)/HAp specimens were prepared from varied mix design inputs, which were varied solid mixtures (different amounts of MK loading in HAp) and liquid-to-solid (L/S) ratios, before being pressed and sintered at 900 °C. Phase analysis, thermal analysis, surface morphology, and tensile strength of the specimens were investigated to study the influences of the Al, Si, Fe, Na, and K composition on the formation of the hydroxyapatite phase and its tensile strength. XRD analysis results show the formation of different phases was obtained from the different mix design inputs HAp (hexagonal and monoclinic), calcium phosphate, sodium calcium phosphate silicate and calcium hydrogen phosphate hydrate. Interestingly, the specimen with the addition of 30 g MK prepared at a 1.25 L/S ratio showed the formation of a monoclinic hydroxyapatite phase, resulting in the highest diametrical tensile strength of 12.52 MPa. Moreover, the increment in the MK amount in the specimens promotes better densification when sintered at 900 °C, which was highlighted in the microstructure study. This may be attributed to the Fe2O3, Na2O, and K2O contents in the MK and alkaline activator, which acted as a self-fluxing agent and contributed to the lower sintering temperature. Therefore, the research revealed that the addition of MK in the activated-HAp system could achieve a stable hydroxyapatite phase and better tensile strength at a low sintering temperature.
- 16 January 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 368
The potential of industrial waste: Electric arc furnace slag (EAF) as recycled road construction materials
- 16 January 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 368
The potential of industrial waste: Electric arc furnace slag (EAF) as recycled road construction materials
- Open Access
- 22 October 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (21) , 11692
Improved Mechanical Properties of Cement-Stabilized Soft Clay Using Garnet Residues and Tire-Derived Aggregates for Subgrade Applications
The growth of the global economy in recent years has resulted in an increase in infrastructure projects worldwide and consequently, this has led to an increase in the quantity of waste generated. Two recycled materials, namely garnet residues (GR) and tire-derived aggregates (TDA), were used to improve mechanical properties of soft clay (SC) subgrade in this study. GR was evaluated as a replacement material in SC prior to Type I Portland cement stabilization. TDA was also studied as an elastic material in cement-stabilized SC–GR. The laboratory tests on the cement–TDA-stabilized SC–GR included unconfined compressive strength (UCS), indirect tensile stress (ITS) and indirect tensile fatigue (ITF). Microstructural analysis on the cement–TDA-stabilized SC–GR was also performed to illustrate the role of GR and TDA contents on the degree of hydration. The UCS of cement-stabilized SC–GR increased when cement content increased from 0% to 2%. Beyond 2% cement content, the UCS development was slightly slower, possibly due to the presence of insufficient water for hydration. The GR reduces the specific surface and particle contacts of the SC–GR blends to be bonded with cementitious products. The optimum SC:GR providing the highest UCS was found to be 90:10 for all cement contents. Increased amounts of GR led to a reduction in UCS values due to its high water absorption, resulting in the insufficient water for the cement hydration. Moreover, the excessive GR replacement ratio weakened the interparticle bond strength due to its smooth and round particles. The TDA addition can enhance the fatigue resistance of the cement-stabilized SC–GR. The maximum fatigue life was found at 2% TDA content. The excessive TDA caused large amounts of micro-cracks in cement–TDA-stabilized SC–GR due to the low adhesion property of TDA. The SC:GR = 90:10, cement content = 2% and TDA content = 2% were suggested as the optimum ingredients. The outcome of this research will promote the usage of GR and TDA to develop a green high-fatigue-resistant subgrade material.
- 22 October 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (21) , 11692
Open AccessImproved Mechanical Properties of Cement-Stabilized Soft Clay Using Garnet Residues and Tire-Derived Aggregates for Subgrade Applications
The growth of the global economy in recent years has resulted in an increase in infrastructure projects worldwide and consequently, this has led to an increase in the quantity of waste generated. Two recycled materials, namely garnet residues (GR) and tire-derived aggregates (TDA), were used to improve mechanical properties of soft clay (SC) subgrade in this study. GR was evaluated as a replacement material in SC prior to Type I Portland cement stabilization. TDA was also studied as an elastic material in cement-stabilized SC–GR. The laboratory tests on the cement–TDA-stabilized SC–GR included unconfined compressive strength (UCS), indirect tensile stress (ITS) and indirect tensile fatigue (ITF). Microstructural analysis on the cement–TDA-stabilized SC–GR was also performed to illustrate the role of GR and TDA contents on the degree of hydration. The UCS of cement-stabilized SC–GR increased when cement content increased from 0% to 2%. Beyond 2% cement content, the UCS development was slightly slower, possibly due to the presence of insufficient water for hydration. The GR reduces the specific surface and particle contacts of the SC–GR blends to be bonded with cementitious products. The optimum SC:GR providing the highest UCS was found to be 90:10 for all cement contents. Increased amounts of GR led to a reduction in UCS values due to its high water absorption, resulting in the insufficient water for the cement hydration. Moreover, the excessive GR replacement ratio weakened the interparticle bond strength due to its smooth and round particles. The TDA addition can enhance the fatigue resistance of the cement-stabilized SC–GR. The maximum fatigue life was found at 2% TDA content. The excessive TDA caused large amounts of micro-cracks in cement–TDA-stabilized SC–GR due to the low adhesion property of TDA. The SC:GR = 90:10, cement content = 2% and TDA content = 2% were suggested as the optimum ingredients. The outcome of this research will promote the usage of GR and TDA to develop a green high-fatigue-resistant subgrade material.
- Open Access
- 26 March 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (7) , 2973
Load Bearing Capacity of Cohesive-Frictional Soils Reinforced with Full-Wraparound Geotextiles: Experimental and Numerical Investigation
This research investigated the effects of types of cohesive-frictional soil and geotextile reinforcement configurations on the bearing capacity of reinforced soil foundation (RSF) structures, via laboratory test and numerical simulation. The four reinforcement configurations studied for the RSF included: (i) horizontal planar form of geotextile, (ii) full-wraparound ends of geotextile, (iii) full-wraparound ends of geotextile with filled-in sand, and (iv) full-wraparound ends of geotextile with filled-in sand and sand backfill. The foundation soils studied were mixtures of fine sand and sodium bentonite at replacement ratios of 0, 20, 40, 60, 80, and 100% by dry weight of sand to have various values of plasticity index (PI). The numerical analysis of RSF structures was performed using PLAXIS 2D software. Several factors were studied, which included: embedment depth of the top reinforcement layer (U), width of horizontal planar form of the reinforcement (W), and spacing between geotextile reinforcement layers (H). Number of reinforcement layers (N) was varied to determine the optimum parameters of U/B, W/B, H/B, and N, where B is the footing width. The most effective improvement technique was found for the full wraparound ends of geotextile with filled-in sand and sand backfill. The outcome of this research will provide a preliminary guideline in a design of RSF structure with different ground soils and other RSF structures with different geosynthetic types.
- 26 March 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (7) , 2973
Open AccessLoad Bearing Capacity of Cohesive-Frictional Soils Reinforced with Full-Wraparound Geotextiles: Experimental and Numerical Investigation
This research investigated the effects of types of cohesive-frictional soil and geotextile reinforcement configurations on the bearing capacity of reinforced soil foundation (RSF) structures, via laboratory test and numerical simulation. The four reinforcement configurations studied for the RSF included: (i) horizontal planar form of geotextile, (ii) full-wraparound ends of geotextile, (iii) full-wraparound ends of geotextile with filled-in sand, and (iv) full-wraparound ends of geotextile with filled-in sand and sand backfill. The foundation soils studied were mixtures of fine sand and sodium bentonite at replacement ratios of 0, 20, 40, 60, 80, and 100% by dry weight of sand to have various values of plasticity index (PI). The numerical analysis of RSF structures was performed using PLAXIS 2D software. Several factors were studied, which included: embedment depth of the top reinforcement layer (U), width of horizontal planar form of the reinforcement (W), and spacing between geotextile reinforcement layers (H). Number of reinforcement layers (N) was varied to determine the optimum parameters of U/B, W/B, H/B, and N, where B is the footing width. The most effective improvement technique was found for the full wraparound ends of geotextile with filled-in sand and sand backfill. The outcome of this research will provide a preliminary guideline in a design of RSF structure with different ground soils and other RSF structures with different geosynthetic types.
- 1 December 2016
- Published by Emerald Publishing in Geosynthetics International
- Vol. 23 (6) , 435-451
Numerical parametric study on behavior of bearing reinforcement earth walls with different backfill material properties
This paper presents a numerical parametric study on behavior of bearing reinforcement earth (BRE) walls with different backfill properties using the finite-element method software PLAXIS 2D. The primary objective of this study was to improve the understanding of bearing stress, settlement, lateral earth pressure, and horizontal wall movement of BRE walls with different backfill materials. The second objective of this study was to evaluate the effects of various soil–structure interactions, foundations, and stiffness of reinforcements on horizontal wall deformations. The backfill materials consisted of four types of soil, which were mixtures of silty clay and sand at different fine contents of 2, 20, 40, and 80% by dry weight. The model parameters for the numerical simulation were obtained from the conventional laboratory tests and back-calculated from the laboratory pullout tests of the bearing reinforcement. The geotextile elements were used to model the bearing reinforcements by converting the contribution of friction and bearing resistances to the equivalent friction resistance, which was represented by the soil–bearing reinforcement interaction ratio, Rinter. The values of Rinter decreased following a polynomial function as an increase of fine content in the ranges of 0.65–0.38 and 0.75–0.40 for the numbers of transverse members, n = 2 and 3, respectively. The simulated bearing stress in the reinforced zone decreased from the front to the back of the wall because the BRE wall behaved as a rigid body built on the relatively firm foundation retaining the unreinforced backfill. The foundation settlement decreased from the facing of the wall to the unreinforced zone for all backfill properties due to the slight rotation of the wall. The relationship between the maximum horizontal wall movement and the fine content can be expressed by a polynomial function. The maximum horizontal wall movement significantly increased as the fine content increased. The excessive movement was realized when the fine content was greater than 45%. The increase of the fine content moved the location of the maximum wall movement higher up from the mid to the top of the wall. A numerical parametric study was conducted to investigate the soil–structure interaction, foundation, and stiffness of reinforcement. These parameters affected the horizontal wall deformation, which is especially important for serviceability of BRE walls. The knowledge gained from this study provides a preliminary guideline in predicting the behavior of BRE walls and may be used to investigate other BRE walls with different wall heights and features of bearing reinforcements.
- 1 December 2016
- Published by Emerald Publishing in Geosynthetics International
- Vol. 23 (6) , 435-451
Numerical parametric study on behavior of bearing reinforcement earth walls with different backfill material properties
This paper presents a numerical parametric study on behavior of bearing reinforcement earth (BRE) walls with different backfill properties using the finite-element method software PLAXIS 2D. The primary objective of this study was to improve the understanding of bearing stress, settlement, lateral earth pressure, and horizontal wall movement of BRE walls with different backfill materials. The second objective of this study was to evaluate the effects of various soil–structure interactions, foundations, and stiffness of reinforcements on horizontal wall deformations. The backfill materials consisted of four types of soil, which were mixtures of silty clay and sand at different fine contents of 2, 20, 40, and 80% by dry weight. The model parameters for the numerical simulation were obtained from the conventional laboratory tests and back-calculated from the laboratory pullout tests of the bearing reinforcement. The geotextile elements were used to model the bearing reinforcements by converting the contribution of friction and bearing resistances to the equivalent friction resistance, which was represented by the soil–bearing reinforcement interaction ratio, Rinter. The values of Rinter decreased following a polynomial function as an increase of fine content in the ranges of 0.65–0.38 and 0.75–0.40 for the numbers of transverse members, n = 2 and 3, respectively. The simulated bearing stress in the reinforced zone decreased from the front to the back of the wall because the BRE wall behaved as a rigid body built on the relatively firm foundation retaining the unreinforced backfill. The foundation settlement decreased from the facing of the wall to the unreinforced zone for all backfill properties due to the slight rotation of the wall. The relationship between the maximum horizontal wall movement and the fine content can be expressed by a polynomial function. The maximum horizontal wall movement significantly increased as the fine content increased. The excessive movement was realized when the fine content was greater than 45%. The increase of the fine content moved the location of the maximum wall movement higher up from the mid to the top of the wall. A numerical parametric study was conducted to investigate the soil–structure interaction, foundation, and stiffness of reinforcement. These parameters affected the horizontal wall deformation, which is especially important for serviceability of BRE walls. The knowledge gained from this study provides a preliminary guideline in predicting the behavior of BRE walls and may be used to investigate other BRE walls with different wall heights and features of bearing reinforcements.