Kyle G. Scheuer
Kyle G. Scheuer has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Ray G. DeCorby
ECE Department, University of Alberta, 9211-116 St. NW, Edmonton, AB T6G 1H9, Canada
15 shared publications F. B. Romero
ECE Department, University of Alberta, Edmonton, Canada
3 shared publications- Ayden Chen
Ultracoustics Technologies Ltd., 10230 Jasper Ave. NW, Edmonton, AB T5J 4P6, Canada
2 shared publications G. J. Hornig
ECE Department, University of Alberta, 9211-116 St. NW, Edmonton, AB, T6G 1H9, Canada
2 shared publications- Graham Hornig
ECE Department, University of Alberta , 9211-116 St. NW, Edmonton, Alberta T6G 1H9, Canada
2 shared publications - Jake Pretula
ECE Department, University of Alberta, 9211-116 St. NW, Edmonton, AB T6G 1H9, Canada
2 shared publications
Latest Publications
- 26 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (17)
Cavity optomechanical magnetometer actuated by substrate bending
We describe a magnetic field sensor based on a monolithic Fabry–Pérot cavity. The cavities were fabricated in a thin-film buckling process at one surface of a fused silica chip, and the chip was subsequently bonded to a giant magnetostrictive material. External magnetic fields drive flexural modes of the assembly and the associated bending stresses are efficiently mapped to changes in the cavity height, with enhanced response at kHz-range mechanical resonance frequencies. A key attribute of this platform is that the size of the transducing material is decoupled from the size of the optical cavity. The buckled cavity operates in low mode order and with moderate Q ∼ 103, providing a high optomechanical coupling coefficient while also enabling a straightforward tuned-to-slope readout technique. Peak sensitivity of ∼2 pT/Hz1/2 was achieved in an unshielded laboratory environment, limited by laser phase and electronics noise in the readout system. With future reductions in these noise sources, we predict that a broadband thermomechanical-noise-limited sensitivity in the ∼0.1 pT/Hz1/2 range is feasible.
- 26 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (17)
Cavity optomechanical magnetometer actuated by substrate bending
We describe a magnetic field sensor based on a monolithic Fabry–Pérot cavity. The cavities were fabricated in a thin-film buckling process at one surface of a fused silica chip, and the chip was subsequently bonded to a giant magnetostrictive material. External magnetic fields drive flexural modes of the assembly and the associated bending stresses are efficiently mapped to changes in the cavity height, with enhanced response at kHz-range mechanical resonance frequencies. A key attribute of this platform is that the size of the transducing material is decoupled from the size of the optical cavity. The buckled cavity operates in low mode order and with moderate Q ∼ 103, providing a high optomechanical coupling coefficient while also enabling a straightforward tuned-to-slope readout technique. Peak sensitivity of ∼2 pT/Hz1/2 was achieved in an unshielded laboratory environment, limited by laser phase and electronics noise in the readout system. With future reductions in these noise sources, we predict that a broadband thermomechanical-noise-limited sensitivity in the ∼0.1 pT/Hz1/2 range is feasible.
- Open Access
Non-Contact Characterization of Plates Using a Turbulent Air-Jet Source and an Ultrasound Microphone
We report on the non-contact characterization of various plate materials (including aluminum and steel) using a high-pressure, micrometer-scale air jet as a broadband ultrasound source and an optomechanical microphone as a receiver. Through-plate transmission spectra are dominated by zero-group-velocity (ZGV) Lamb modes. We attribute this to the ‘point-like’ nature of both the source and receiver, since ZGV modes are spatially localized and comprise a range of non-normal wave numbers. As is well known, the properties of the ZGV modes, including their frequency and amplitude, are sensitive to thickness variations or the presence of defects. The continuous nature and high acoustic power of the gas jet source enabled us to perform uninterrupted scanning of non-uniform steel plates. Given the ubiquitous and low-cost nature of compressed air systems, our approach might be of interest for the rapid inspection of industrial parts.
Open AccessNon-Contact Characterization of Plates Using a Turbulent Air-Jet Source and an Ultrasound Microphone
We report on the non-contact characterization of various plate materials (including aluminum and steel) using a high-pressure, micrometer-scale air jet as a broadband ultrasound source and an optomechanical microphone as a receiver. Through-plate transmission spectra are dominated by zero-group-velocity (ZGV) Lamb modes. We attribute this to the ‘point-like’ nature of both the source and receiver, since ZGV modes are spatially localized and comprise a range of non-normal wave numbers. As is well known, the properties of the ZGV modes, including their frequency and amplitude, are sensitive to thickness variations or the presence of defects. The continuous nature and high acoustic power of the gas jet source enabled us to perform uninterrupted scanning of non-uniform steel plates. Given the ubiquitous and low-cost nature of compressed air systems, our approach might be of interest for the rapid inspection of industrial parts.
- Open Access
Resonant Ultrasound Spectroscopy Detection Using a Non-Contact Ultrasound Microphone
We observed vibrational eigenmodes for a variety of millimeter-scale objects, including glass and sapphire lenses, by placing them on a piezoelectric ‘shaker’ driven by a broadband noise or frequency sweep signal, and using an optomechanical microphone to pick up their vibrational signatures emitted into the surrounding air. High-quality vibrational modes were detected over the ~0–8 MHz range for a typical object–microphone spacing of 1–10 mm. The observed eigenfrequencies are shown to be in excellent agreement with numerical predictions. Non-contact detection of resonant vibrational eigenmodes in the MHz ultrasound range could find application in the quality control of numerous industrial parts, such as ball bearings and lenses.
Open AccessResonant Ultrasound Spectroscopy Detection Using a Non-Contact Ultrasound Microphone
We observed vibrational eigenmodes for a variety of millimeter-scale objects, including glass and sapphire lenses, by placing them on a piezoelectric ‘shaker’ driven by a broadband noise or frequency sweep signal, and using an optomechanical microphone to pick up their vibrational signatures emitted into the surrounding air. High-quality vibrational modes were detected over the ~0–8 MHz range for a typical object–microphone spacing of 1–10 mm. The observed eigenfrequencies are shown to be in excellent agreement with numerical predictions. Non-contact detection of resonant vibrational eigenmodes in the MHz ultrasound range could find application in the quality control of numerous industrial parts, such as ball bearings and lenses.
- 1 July 2025
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 158 (1) , 329-335
Characterization of micro-scale gas leaks using an optomechanical ultrasound sensor
We used an optomechanical microphone to measure the acoustic signals emitted by compressed-air jets emanating from apertures as small as ∼5 μm. In keeping with the predictions of aeroacoustic theory, spectra extending into the high-frequency (MHz) ultrasound region were observed. Most of this acoustic energy lies well above the range of a conventional ultrasonic microphone. Conversely, the broadband response of the optomechanical sensor offers the potential to localize and quantify leaks based on a more complete knowledge of the acoustic spectrum. We show that the minimum detectable flow rate, set by the onset of turbulence, scales with the hole size and was as low as ∼10−3 Pa·m3·s−1 for the smallest holes studied here. The results demonstrate that a sufficiently broadband and sensitive microphone might enhance the utility of “acoustic sniffer” tools for quantitative gas leak detection.
- 1 July 2025
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 158 (1) , 329-335
Characterization of micro-scale gas leaks using an optomechanical ultrasound sensor
We used an optomechanical microphone to measure the acoustic signals emitted by compressed-air jets emanating from apertures as small as ∼5 μm. In keeping with the predictions of aeroacoustic theory, spectra extending into the high-frequency (MHz) ultrasound region were observed. Most of this acoustic energy lies well above the range of a conventional ultrasonic microphone. Conversely, the broadband response of the optomechanical sensor offers the potential to localize and quantify leaks based on a more complete knowledge of the acoustic spectrum. We show that the minimum detectable flow rate, set by the onset of turbulence, scales with the hole size and was as low as ∼10−3 Pa·m3·s−1 for the smallest holes studied here. The results demonstrate that a sufficiently broadband and sensitive microphone might enhance the utility of “acoustic sniffer” tools for quantitative gas leak detection.
- Open Access
- 25 March 2025
- Published by MDPI AG in Preprints.org
Characterization and Localization of Micro-Scale Gas Leaks Using an Optomechanical Ultrasound Sensor
We used an optomechanical microphone to measure the acoustic signals emitted by compressed-air jets emanating from apertures as small as ~ 5 um. In keeping with the predictions of aeroacoustic theory, spectra extending into the high-frequency (MHz) ultrasound region were observed. Most of this acoustic energy lies well above the range of a conventional ultrasonic microphone. Conversely, the broadband response of the optomechanical sensor offers the potential to localize and quantify leaks based on a more complete knowledge of the acoustic spectrum. We show that the minimum detectable flow rate, set by the onset of turbulence, scales with the hole size and was as low as ~ 10^-3 Pa·m^3·s^-1 for the smallest holes studied here. The results demonstrate that a sufficiently broadband and sensitive microphone might enhance the utility of ‘acoustic sniffer’ tools for quantitative gas leak detection.
- 25 March 2025
- Published by MDPI AG in Preprints.org
Open AccessCharacterization and Localization of Micro-Scale Gas Leaks Using an Optomechanical Ultrasound Sensor
We used an optomechanical microphone to measure the acoustic signals emitted by compressed-air jets emanating from apertures as small as ~ 5 um. In keeping with the predictions of aeroacoustic theory, spectra extending into the high-frequency (MHz) ultrasound region were observed. Most of this acoustic energy lies well above the range of a conventional ultrasonic microphone. Conversely, the broadband response of the optomechanical sensor offers the potential to localize and quantify leaks based on a more complete knowledge of the acoustic spectrum. We show that the minimum detectable flow rate, set by the onset of turbulence, scales with the hole size and was as low as ~ 10^-3 Pa·m^3·s^-1 for the smallest holes studied here. The results demonstrate that a sufficiently broadband and sensitive microphone might enhance the utility of ‘acoustic sniffer’ tools for quantitative gas leak detection.
- Open Access
- 26 December 2024
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 10 (1) , 1-9
Coupling the thermal acoustic modes of a bubble to an optomechanical sensor
Optomechanical sensors provide a platform for probing acoustic/vibrational properties at the micro-scale. Here, we used cavity optomechanical sensors to interrogate the acoustic environment of adjacent air bubbles in water. We report experimental observations of the volume acoustic modes of these bubbles, including both the fundamental Minnaert breathing mode and a family of higher-order modes extending into the megahertz frequency range. Bubbles were placed on or near optomechanical sensors having a noise floor substantially determined by ambient medium fluctuations, and which are thus able to detect thermal motions of proximate objects. Bubble motions could be coupled to the sensor through both air (i.e., with the sensor inside the bubble) and water, verifying that sound is radiated by the high-order modes. We also present evidence for elastic-Purcell-effect modifications of the sensor’s vibrational spectrum when encapsulated by a bubble, in the form of cavity-modified linewidths and line shifts. Our results could increase the understanding of bubble acoustics relevant to a variety of fields such as lab-on-a-chip microfluidics and biosensing, and could also inform future efforts to optimize the properties of micro-mechanical oscillators.
- 26 December 2024
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 10 (1) , 1-9
Open AccessCoupling the thermal acoustic modes of a bubble to an optomechanical sensor
Optomechanical sensors provide a platform for probing acoustic/vibrational properties at the micro-scale. Here, we used cavity optomechanical sensors to interrogate the acoustic environment of adjacent air bubbles in water. We report experimental observations of the volume acoustic modes of these bubbles, including both the fundamental Minnaert breathing mode and a family of higher-order modes extending into the megahertz frequency range. Bubbles were placed on or near optomechanical sensors having a noise floor substantially determined by ambient medium fluctuations, and which are thus able to detect thermal motions of proximate objects. Bubble motions could be coupled to the sensor through both air (i.e., with the sensor inside the bubble) and water, verifying that sound is radiated by the high-order modes. We also present evidence for elastic-Purcell-effect modifications of the sensor’s vibrational spectrum when encapsulated by a bubble, in the form of cavity-modified linewidths and line shifts. Our results could increase the understanding of bubble acoustics relevant to a variety of fields such as lab-on-a-chip microfluidics and biosensing, and could also inform future efforts to optimize the properties of micro-mechanical oscillators.
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Air-coupled ultrasound using broadband shock waves from piezoelectric spark igniters
We used an optomechanical sensor to study the ultrasound generated by manually operated piezoelectric spark igniters. These low-energy sparks produce short-duration acoustic shock-wave pulses, with sub-microsecond rise times and frequency content extending well beyond 2 MHz in air. The same source–receiver combination was then used to demonstrate broadband characterization of solid (polymer and glass) plates in a simple setup, where single spark events yielded high signal-to-noise ratio data without the need for critical alignment. This setup also enabled us to estimate pressure excursions approaching 105 Pa at millimeter-scale distances from the spark. The results are in large part made possible by the small size, wide bandwidth, and high sensitivity of the optomechanical sensor and might be of interest for air-coupled ultrasound applications in nondestructive testing.
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Air-coupled ultrasound using broadband shock waves from piezoelectric spark igniters
We used an optomechanical sensor to study the ultrasound generated by manually operated piezoelectric spark igniters. These low-energy sparks produce short-duration acoustic shock-wave pulses, with sub-microsecond rise times and frequency content extending well beyond 2 MHz in air. The same source–receiver combination was then used to demonstrate broadband characterization of solid (polymer and glass) plates in a simple setup, where single spark events yielded high signal-to-noise ratio data without the need for critical alignment. This setup also enabled us to estimate pressure excursions approaching 105 Pa at millimeter-scale distances from the spark. The results are in large part made possible by the small size, wide bandwidth, and high sensitivity of the optomechanical sensor and might be of interest for air-coupled ultrasound applications in nondestructive testing.
- 12 June 2024
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 14 (7) , 1793-1802
Spectroscopy of substrate thermal vibrational modes using an optomechanical sensor
We used an optomechanical sensor to record the vibrational spectrum of its own fused silica substrate. The coupling of the substrate modes was greatly enhanced by covering the sensor with an appropriately sized ethylene glycol droplet, and in that case even thermally populated modes could be clearly detected. We observed a rich spectrum of high-quality flexural modes for frequencies less than ∼ 10 MHz, in good agreement with analytical theory and finite element simulations. We also observed signatures of acoustic waves resonantly confined by the droplet, over the entire ∼ 0–40 MHz range of the experiment. This work could inform efforts to increase the quality factor of mechanical resonators, and the use of substrate phonon modes as information channels.
- 12 June 2024
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 14 (7) , 1793-1802
Spectroscopy of substrate thermal vibrational modes using an optomechanical sensor
We used an optomechanical sensor to record the vibrational spectrum of its own fused silica substrate. The coupling of the substrate modes was greatly enhanced by covering the sensor with an appropriately sized ethylene glycol droplet, and in that case even thermally populated modes could be clearly detected. We observed a rich spectrum of high-quality flexural modes for frequencies less than ∼ 10 MHz, in good agreement with analytical theory and finite element simulations. We also observed signatures of acoustic waves resonantly confined by the droplet, over the entire ∼ 0–40 MHz range of the experiment. This work could inform efforts to increase the quality factor of mechanical resonators, and the use of substrate phonon modes as information channels.
- 31 October 2023
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 23 (24) , 5131-5138
Ultrasonic spectroscopy of sessile droplets coupled to optomechanical sensors
We describe the passive sensing of high-frequency vibrational modes of sessile droplets using integrated optomechanical sensors. This approach has potential to enable acoustic spectroscopy of liquid samples in an open microfluidics platform.
- 31 October 2023
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 23 (24) , 5131-5138
Ultrasonic spectroscopy of sessile droplets coupled to optomechanical sensors
We describe the passive sensing of high-frequency vibrational modes of sessile droplets using integrated optomechanical sensors. This approach has potential to enable acoustic spectroscopy of liquid samples in an open microfluidics platform.
- Open Access
- 24 July 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (4)
Observation of thermal acoustic modes of a droplet coupled to an optomechanical sensor
The bulk acoustic modes of liquid droplets, well understood from a theoretical perspective, have rarely been observed experimentally. Here, we report the indirect observation of acoustic vibrational modes in a picoliter-scale droplet, extending up to ∼40 MHz. This was achieved by coupling the droplet to an ultra-sensitive optomechanical sensor, which operates in a thermal-noise limited regime and with a substantial contribution from acoustic noise in the ambient medium. The droplet vibrational modes manifest as Fano resonances in the thermal noise spectrum of the sensor. This is among the few reported observations of droplet acoustic modes and of Fano interactions in a coupled mechanical oscillator system driven only by thermal Brownian motion.
- 24 July 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (4)
Open AccessObservation of thermal acoustic modes of a droplet coupled to an optomechanical sensor
The bulk acoustic modes of liquid droplets, well understood from a theoretical perspective, have rarely been observed experimentally. Here, we report the indirect observation of acoustic vibrational modes in a picoliter-scale droplet, extending up to ∼40 MHz. This was achieved by coupling the droplet to an ultra-sensitive optomechanical sensor, which operates in a thermal-noise limited regime and with a substantial contribution from acoustic noise in the ambient medium. The droplet vibrational modes manifest as Fano resonances in the thermal noise spectrum of the sensor. This is among the few reported observations of droplet acoustic modes and of Fano interactions in a coupled mechanical oscillator system driven only by thermal Brownian motion.