Giuseppe Cimò
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Giuseppe Cimò has a total of 195 co-authors. Here are the top co-authors by number of shared publications:
- Guifré Molera Calvés
University of Tasmania
15 shared publications - Leonid I. Gurvits
Joint Institute for VLBI ERIC
14 shared publications - Dominic Dirkx
Delft University of Technology, Kluyverweg 1, 2629 HS, Delft, The Netherlands
8 shared publications - Sándor Frey
Konkoly Observatory
8 shared publications Jasper Edwards
Physics discipline, School of Natural Sciences, University of Tasmania, Private Bag 37, Hobart, TAS 7000, Australia
5 shared publicationsJonathan Quick
Hartebeesthoek Radio Astronomy Observatory, Krugersdorp, South Africa
5 shared publications
Latest Publications
- Open Access
- 16 September 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-26
Reply on RC1
This paper presents the results of Planetary Radio Interferometry and Doppler Experiment (PRIDE) observations of the JUICE spacecraft during its lunar and Earth gravity-assist manoeuvres on August 19 and 20, 2024, using a network of VLBI radio telescopes. Prior to the flyby sequence, VLBI phase‑referencing observations were conducted to establish astrometric measurements and Doppler frequency calibration during the near-Earth approach. During the flyby events, the experiment successfully captured the signal ingress and egress during the lunar occultation, as well as the signal behaviour at closest approach to the lunar surface. Signal-diagnostic measurements were performed to characterise the received carrier signal and assess instrumental and propagation effects. The observed Doppler frequency measurements were subsequently compared with predicted values derived independently using the WebGeocalc service and the Tudat software framework. The close agreement between the measured Doppler observables and model predictions confirms that the tracking results are consistent with expectations for JUICE's cruise-phase configuration and the high-velocity dynamics of the Earth flyby. Finally, these measurements were also used to obtain complementary measurements of the terrestrial ionosphere and space weather conditions, and are being used for refining solar wind models using planetary spacecraft radio tracking.
- 16 September 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-26
Open AccessReply on RC1
This paper presents the results of Planetary Radio Interferometry and Doppler Experiment (PRIDE) observations of the JUICE spacecraft during its lunar and Earth gravity-assist manoeuvres on August 19 and 20, 2024, using a network of VLBI radio telescopes. Prior to the flyby sequence, VLBI phase‑referencing observations were conducted to establish astrometric measurements and Doppler frequency calibration during the near-Earth approach. During the flyby events, the experiment successfully captured the signal ingress and egress during the lunar occultation, as well as the signal behaviour at closest approach to the lunar surface. Signal-diagnostic measurements were performed to characterise the received carrier signal and assess instrumental and propagation effects. The observed Doppler frequency measurements were subsequently compared with predicted values derived independently using the WebGeocalc service and the Tudat software framework. The close agreement between the measured Doppler observables and model predictions confirms that the tracking results are consistent with expectations for JUICE's cruise-phase configuration and the high-velocity dynamics of the Earth flyby. Finally, these measurements were also used to obtain complementary measurements of the terrestrial ionosphere and space weather conditions, and are being used for refining solar wind models using planetary spacecraft radio tracking.
- Open Access
- 19 August 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-26
Comment on egusphere-2026-1936
This paper presents the results of Planetary Radio Interferometry and Doppler Experiment (PRIDE) observations of the JUICE spacecraft during its lunar and Earth gravity-assist manoeuvres on August 19 and 20, 2024, using a network of VLBI radio telescopes. Prior to the flyby sequence, VLBI phase‑referencing observations were conducted to establish astrometric measurements and Doppler frequency calibration during the near-Earth approach. During the flyby events, the experiment successfully captured the signal ingress and egress during the lunar occultation, as well as the signal behaviour at closest approach to the lunar surface. Signal-diagnostic measurements were performed to characterise the received carrier signal and assess instrumental and propagation effects. The observed Doppler frequency measurements were subsequently compared with predicted values derived independently using the WebGeocalc service and the Tudat software framework. The close agreement between the measured Doppler observables and model predictions confirms that the tracking results are consistent with expectations for JUICE's cruise-phase configuration and the high-velocity dynamics of the Earth flyby. Finally, these measurements were also used to obtain complementary measurements of the terrestrial ionosphere and space weather conditions, and are being used for refining solar wind models using planetary spacecraft radio tracking.
- 19 August 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-26
Open AccessComment on egusphere-2026-1936
This paper presents the results of Planetary Radio Interferometry and Doppler Experiment (PRIDE) observations of the JUICE spacecraft during its lunar and Earth gravity-assist manoeuvres on August 19 and 20, 2024, using a network of VLBI radio telescopes. Prior to the flyby sequence, VLBI phase‑referencing observations were conducted to establish astrometric measurements and Doppler frequency calibration during the near-Earth approach. During the flyby events, the experiment successfully captured the signal ingress and egress during the lunar occultation, as well as the signal behaviour at closest approach to the lunar surface. Signal-diagnostic measurements were performed to characterise the received carrier signal and assess instrumental and propagation effects. The observed Doppler frequency measurements were subsequently compared with predicted values derived independently using the WebGeocalc service and the Tudat software framework. The close agreement between the measured Doppler observables and model predictions confirms that the tracking results are consistent with expectations for JUICE's cruise-phase configuration and the high-velocity dynamics of the Earth flyby. Finally, these measurements were also used to obtain complementary measurements of the terrestrial ionosphere and space weather conditions, and are being used for refining solar wind models using planetary spacecraft radio tracking.
- Open Access
- 2 July 2026
- Published by Copernicus GmbH
Orbit determination and error quantification of planetary missions using PRIDE open-loop Doppler data: Application to the Mars Express flyby of Phobos
Doppler tracking of planetary missions is crucial for science objectives related to understanding, among others, solar system interiors and evolution. These analyses conventionally rely on closed-loop Doppler data from networks such as ESTRACK and the DSN. The Planetary Radio Interferometry and Doppler Experiment (PRIDE) can provide complementary data by extracting open-loop Doppler and VLBI observables from spacecraft radio signals recorded by radio-astronomical telescopes [1,2,3]. These (three-way) observables are generated using the existing downlink from the spacecraft and therefore generated concurrently with the typical (usually two-way) closed-loop tracking data. While PRIDE data of planetary missions have been used for various applications, their direct use in a full orbit-estimation problem had not yet been demonstrated. Here, we report on the first end-to-end PRIDE-based orbit estimation of a planetary mission, using PRIDE Doppler data.We use the 2013 Mars Express flyby of Phobos, for which both conventional closed-loop Doppler data and PRIDE open-loop Doppler (EVN experiment GR035, PI: Pascal Rosenblatt) data are available [4]. Using the open-source TU Delft Astrodynamics Toolbox (Tudat) [5,6], we independently estimate the Mars Express trajectory and the gravitational parameter of Phobos from the closed-loop and open-loop datasets. The solutions are cross-validated against the Mars Express orbit computed by the Royal Observatory of Belgium (ROB) team from closed-loop Doppler data using the GINS software.The closed-loop solution gives RMS position differences with respect to the ROB Mars Express ephemerides of approximately 0.27 m radial, 17 m along-track, and 130 m cross-track, consistent with the expected uncertainty of the reference solution. For the PRIDE open-loop Doppler data, we form 27 different three-station combinations of PRIDE datasets, with one station on each of three continents, such that each combination spans the full tracking interval. From each combination, we estimate an independent orbit of Mars Express, leading to separate orbit estimates, each of comparable quality to those derived from closed-loop data, as quantified by the difference with respect to the ROB reference. The estimated gravitational parameter of Phobos is likewise consistent between the open-loop and closed-loop analyses and with reference values from the literature.To further quantify the uncertainty of the PRIDE-based orbit estimates, we compute the RMS dispersion of the 27 station-combination solutions at each point along the estimated trajectory. This dispersion peaks at approximately 0.4 m radial, 15 m along-track, and 100 m cross-track. Its temporal behaviour closely matches the difference between our closed-loop solution and the ROB reference ephemeris, indicating that the spread between PRIDE station-combination solutions provides a measure of the true orbit-estimation error that is comparable to the difference with respect to an external reference solution. This is a key advantage of PRIDE’s multi-station redundancy: it enables an internal assessment of solution uncertainty, without relying exclusively on formal covariance estimates, which are often too optimistic, or on comparison with an external reference solution, which is not always available.Assessing the true uncertainty of radio-tracking-based estimation is crucial for robustly using estimated parameters (for instance the gravitational parameter of Phobos) to improve our understanding of planetary interiors and Solar System evolution. PRIDE observations are particularly valuable for selected tracking intervals of high scientific interest, where the multi-station redundancy can provide validation and error quantification beyond what is available from conventional tracking alone. For events such as flybys of the Galilean moons [3], PRIDE Doppler data can therefore provide a complementary source of information for assessing the reliability of orbit and parameter estimates. Future work will include the processing of PRIDE Doppler data during the JUICE flyby of Venus, and spacecraft orbit estimation using a combination of open- and closed-loop tracking data. [1] Duev, D.A., et al. "Spacecraft VLBI and Doppler tracking: algorithms and implementation." Astronomy & Astrophysics 541 (2012): A43.[2] Molera Calvés, G., et al. "High spectral resolution multi-tone Spacecraft Doppler tracking software: Algorithms and implementations." Publications of the Astronomical Society of Australia 38 (2021): e065.[3] Gurvits, L.I., et al. "Planetary radio interferometry and Doppler experiment (PRIDE) of the JUICE mission." Space Science Reviews 219.8 (2023): 79.[4] Bocanegra-Bahamón, T.M., et al. "Planetary Radio Interferometry and Doppler Experiment (PRIDE) technique: A test case of the Mars Express Phobos Flyby: II. Doppler tracking: Formulation of observed and computed values, and noise budget." Astronomy & Astrophysics 609 (2018): A59.[5] Dirkx, D., et al. "The open-source astrodynamics Tudatpy software–overview for planetary mission design and science analysis." EPSC2022 EPSC2022-253 (2022).[6] Gisolfi, L, et al. "Open-Source High-Fidelity Orbit Estimation for Planetary Science and Space Situational Awareness Using the Tudat Software." arXiv preprint arXiv:2510.23179 (2025).
- 2 July 2026
- Published by Copernicus GmbH
Open AccessOrbit determination and error quantification of planetary missions using PRIDE open-loop Doppler data: Application to the Mars Express flyby of Phobos
Doppler tracking of planetary missions is crucial for science objectives related to understanding, among others, solar system interiors and evolution. These analyses conventionally rely on closed-loop Doppler data from networks such as ESTRACK and the DSN. The Planetary Radio Interferometry and Doppler Experiment (PRIDE) can provide complementary data by extracting open-loop Doppler and VLBI observables from spacecraft radio signals recorded by radio-astronomical telescopes [1,2,3]. These (three-way) observables are generated using the existing downlink from the spacecraft and therefore generated concurrently with the typical (usually two-way) closed-loop tracking data. While PRIDE data of planetary missions have been used for various applications, their direct use in a full orbit-estimation problem had not yet been demonstrated. Here, we report on the first end-to-end PRIDE-based orbit estimation of a planetary mission, using PRIDE Doppler data.We use the 2013 Mars Express flyby of Phobos, for which both conventional closed-loop Doppler data and PRIDE open-loop Doppler (EVN experiment GR035, PI: Pascal Rosenblatt) data are available [4]. Using the open-source TU Delft Astrodynamics Toolbox (Tudat) [5,6], we independently estimate the Mars Express trajectory and the gravitational parameter of Phobos from the closed-loop and open-loop datasets. The solutions are cross-validated against the Mars Express orbit computed by the Royal Observatory of Belgium (ROB) team from closed-loop Doppler data using the GINS software.The closed-loop solution gives RMS position differences with respect to the ROB Mars Express ephemerides of approximately 0.27 m radial, 17 m along-track, and 130 m cross-track, consistent with the expected uncertainty of the reference solution. For the PRIDE open-loop Doppler data, we form 27 different three-station combinations of PRIDE datasets, with one station on each of three continents, such that each combination spans the full tracking interval. From each combination, we estimate an independent orbit of Mars Express, leading to separate orbit estimates, each of comparable quality to those derived from closed-loop data, as quantified by the difference with respect to the ROB reference. The estimated gravitational parameter of Phobos is likewise consistent between the open-loop and closed-loop analyses and with reference values from the literature.To further quantify the uncertainty of the PRIDE-based orbit estimates, we compute the RMS dispersion of the 27 station-combination solutions at each point along the estimated trajectory. This dispersion peaks at approximately 0.4 m radial, 15 m along-track, and 100 m cross-track. Its temporal behaviour closely matches the difference between our closed-loop solution and the ROB reference ephemeris, indicating that the spread between PRIDE station-combination solutions provides a measure of the true orbit-estimation error that is comparable to the difference with respect to an external reference solution. This is a key advantage of PRIDE’s multi-station redundancy: it enables an internal assessment of solution uncertainty, without relying exclusively on formal covariance estimates, which are often too optimistic, or on comparison with an external reference solution, which is not always available.Assessing the true uncertainty of radio-tracking-based estimation is crucial for robustly using estimated parameters (for instance the gravitational parameter of Phobos) to improve our understanding of planetary interiors and Solar System evolution. PRIDE observations are particularly valuable for selected tracking intervals of high scientific interest, where the multi-station redundancy can provide validation and error quantification beyond what is available from conventional tracking alone. For events such as flybys of the Galilean moons [3], PRIDE Doppler data can therefore provide a complementary source of information for assessing the reliability of orbit and parameter estimates. Future work will include the processing of PRIDE Doppler data during the JUICE flyby of Venus, and spacecraft orbit estimation using a combination of open- and closed-loop tracking data. [1] Duev, D.A., et al. "Spacecraft VLBI and Doppler tracking: algorithms and implementation." Astronomy & Astrophysics 541 (2012): A43.[2] Molera Calvés, G., et al. "High spectral resolution multi-tone Spacecraft Doppler tracking software: Algorithms and implementations." Publications of the Astronomical Society of Australia 38 (2021): e065.[3] Gurvits, L.I., et al. "Planetary radio interferometry and Doppler experiment (PRIDE) of the JUICE mission." Space Science Reviews 219.8 (2023): 79.[4] Bocanegra-Bahamón, T.M., et al. "Planetary Radio Interferometry and Doppler Experiment (PRIDE) technique: A test case of the Mars Express Phobos Flyby: II. Doppler tracking: Formulation of observed and computed values, and noise budget." Astronomy & Astrophysics 609 (2018): A59.[5] Dirkx, D., et al. "The open-source astrodynamics Tudatpy software–overview for planetary mission design and science analysis." EPSC2022 EPSC2022-253 (2022).[6] Gisolfi, L, et al. "Open-Source High-Fidelity Orbit Estimation for Planetary Science and Space Situational Awareness Using the Tudat Software." arXiv preprint arXiv:2510.23179 (2025).
- Open Access
- 2 July 2026
- Published by Copernicus GmbH
Two years of Planetary Radio Interferometry and Doppler Experiment for the ESA’s JUICE mission
Ground-based radio astronomy and space science get together in the Planetary Radio Interferometry and Doppler Experiment (PRIDE), which provides the precise determination of the lateral position of spacecraft on the celestial sphere using phase referencing near-field Very Long Baseline Interferometry (VLBI).As part of the ESA Jupiter Icy Moons Explorer (JUICE) mission, PRIDE is complementary to on-board radio science experiments. The technique consists of radio astronomical observations of the JUICE radio signal alongside calibrating quasars to deliver high-resolution lateral position measurements within the International Celestial Reference Frame. PRIDE requires no extra onboard instruments and relies on the spacecraft's existing telecommunications system and ground-based telescope arrays, like the European VLBI Network or the Australian Long Baseline Array.Since JUICE launch, PRIDE observations have tracked the spacecraft on several occasions. During the Lunar-Earth Gravity Assist (LEGA), multiple radio telescopes observed JUICE to independently validate the spacecraft trajectory to verify PRIDE internal pipelines. In August 2025, the European VLBI Network ran an observing campaign during the Venus gravity assist manoeuvres. In this presentation, the status and the results of the PRIDE-JUICE cruise phase activities will be presented.
- 2 July 2026
- Published by Copernicus GmbH
Open AccessTwo years of Planetary Radio Interferometry and Doppler Experiment for the ESA’s JUICE mission
Ground-based radio astronomy and space science get together in the Planetary Radio Interferometry and Doppler Experiment (PRIDE), which provides the precise determination of the lateral position of spacecraft on the celestial sphere using phase referencing near-field Very Long Baseline Interferometry (VLBI).As part of the ESA Jupiter Icy Moons Explorer (JUICE) mission, PRIDE is complementary to on-board radio science experiments. The technique consists of radio astronomical observations of the JUICE radio signal alongside calibrating quasars to deliver high-resolution lateral position measurements within the International Celestial Reference Frame. PRIDE requires no extra onboard instruments and relies on the spacecraft's existing telecommunications system and ground-based telescope arrays, like the European VLBI Network or the Australian Long Baseline Array.Since JUICE launch, PRIDE observations have tracked the spacecraft on several occasions. During the Lunar-Earth Gravity Assist (LEGA), multiple radio telescopes observed JUICE to independently validate the spacecraft trajectory to verify PRIDE internal pipelines. In August 2025, the European VLBI Network ran an observing campaign during the Venus gravity assist manoeuvres. In this presentation, the status and the results of the PRIDE-JUICE cruise phase activities will be presented.
- Open Access
- 21 April 2026
- Published by Copernicus GmbH in EGUsphere
- Vol. 2026
Mapping JUICE’s Journey: PRIDE observations from the Lunar-Earth Gravity Assist
This paper presents the results of Planetary Radio Interferometry and Doppler Experiment (PRIDE) observations of the JUICE spacecraft during its lunar and Earth gravity-assist manoeuvres on August 19 and 20, 2024, using a network of VLBI radio telescopes. Prior to the flyby sequence, VLBI phase‑referencing observations were conducted to establish astrometric measurements and Doppler frequency calibration during the near-Earth approach. During the flyby events, the experiment successfully captured the signal ingress and egress during the lunar occultation, as well as the signal behaviour at closest approach to the lunar surface. Signal-diagnostic measurements were performed to characterise the received carrier signal and assess instrumental and propagation effects. The observed Doppler frequency measurements were subsequently compared with predicted values derived independently using the WebGeocalc service and the Tudat software framework. The close agreement between the measured Doppler observables and model predictions confirms that the tracking results are consistent with expectations for JUICE's cruise-phase configuration and the high-velocity dynamics of the Earth flyby. Finally, these measurements were also used to obtain complementary measurements of the terrestrial ionosphere and space weather conditions, and are being used for refining solar wind models using planetary spacecraft radio tracking.
- 21 April 2026
- Published by Copernicus GmbH in EGUsphere
- Vol. 2026
Open AccessMapping JUICE’s Journey: PRIDE observations from the Lunar-Earth Gravity Assist
This paper presents the results of Planetary Radio Interferometry and Doppler Experiment (PRIDE) observations of the JUICE spacecraft during its lunar and Earth gravity-assist manoeuvres on August 19 and 20, 2024, using a network of VLBI radio telescopes. Prior to the flyby sequence, VLBI phase‑referencing observations were conducted to establish astrometric measurements and Doppler frequency calibration during the near-Earth approach. During the flyby events, the experiment successfully captured the signal ingress and egress during the lunar occultation, as well as the signal behaviour at closest approach to the lunar surface. Signal-diagnostic measurements were performed to characterise the received carrier signal and assess instrumental and propagation effects. The observed Doppler frequency measurements were subsequently compared with predicted values derived independently using the WebGeocalc service and the Tudat software framework. The close agreement between the measured Doppler observables and model predictions confirms that the tracking results are consistent with expectations for JUICE's cruise-phase configuration and the high-velocity dynamics of the Earth flyby. Finally, these measurements were also used to obtain complementary measurements of the terrestrial ionosphere and space weather conditions, and are being used for refining solar wind models using planetary spacecraft radio tracking.
- Open Access
- 15 April 2025
- Published by Cambridge University Press (CUP) in Publications of the Astronomical Society of Australia
- Vol. 42, 1-14
Estimating the noise budget and system noise levels in closed-loop Doppler tracking of ESA’s Mars Express with VLBI radio telescopes
The radio telescopes of the European VLBI Network (EVN) and the University of Tasmania (UTAS) conducted an extensive observation campaign of the European Space Agency’s (ESA) Mars Express (MEX) spacecraft between 2013 and 2020. The campaign, carried out under the Planetary Radio Interferometry and Doppler Experiment (PRIDE) framework, aimed to study interplanetary phase scintillation and assess the noise budget in the closed-loop Doppler observations. The average closed-loop Doppler noise was determined to be approximately 10 mHz at a 10-s integration time, reaffirming the technique’s suitability for radio science experiments. We evaluated how different observational parameters such as the solar elongation, antenna size, and elevation angle impact the Doppler noise. A key part of the analysis involved comparing results from co-located telescopes to investigate system noise effects. Co-located telescopes at both Wettzell and Hobart provided highly consistent results, with any deviations serving as diagnostic tools to identify station-dependent issues. Additionally, the use of phase calibration tones during spacecraft tracking showed that the instrumental noise contribution is of the order of 5 $\%$ of the total noise. This study provides a detailed noise budget for closed-loop Doppler observations with VLBI telescopes while emphasizing the effectiveness of the co-location method in isolating system-level noise. These findings are important for optimizing future radio science and VLBI tracking missions using stations outside the the Deep Space Network (DSN) and European Space Tracking (ESTRACK) network.- 15 April 2025
- Published by Cambridge University Press (CUP) in Publications of the Astronomical Society of Australia
- Vol. 42, 1-14
Open AccessEstimating the noise budget and system noise levels in closed-loop Doppler tracking of ESA’s Mars Express with VLBI radio telescopes
The radio telescopes of the European VLBI Network (EVN) and the University of Tasmania (UTAS) conducted an extensive observation campaign of the European Space Agency’s (ESA) Mars Express (MEX) spacecraft between 2013 and 2020. The campaign, carried out under the Planetary Radio Interferometry and Doppler Experiment (PRIDE) framework, aimed to study interplanetary phase scintillation and assess the noise budget in the closed-loop Doppler observations. The average closed-loop Doppler noise was determined to be approximately 10 mHz at a 10-s integration time, reaffirming the technique’s suitability for radio science experiments. We evaluated how different observational parameters such as the solar elongation, antenna size, and elevation angle impact the Doppler noise. A key part of the analysis involved comparing results from co-located telescopes to investigate system noise effects. Co-located telescopes at both Wettzell and Hobart provided highly consistent results, with any deviations serving as diagnostic tools to identify station-dependent issues. Additionally, the use of phase calibration tones during spacecraft tracking showed that the instrumental noise contribution is of the order of 5 $\%$ of the total noise. This study provides a detailed noise budget for closed-loop Doppler observations with VLBI telescopes while emphasizing the effectiveness of the co-location method in isolating system-level noise. These findings are important for optimizing future radio science and VLBI tracking missions using stations outside the the Deep Space Network (DSN) and European Space Tracking (ESTRACK) network. - Open Access
- 7 March 2025
- Published by Springer Nature in Experimental Astronomy
- Vol. 59 (2) , 1-21
Simultaneous multi-spacecraft observations with VLBI radio telescopes to study the interplanetary phase scintillation
Ground-based observations of spacecraft signals have been used to study space weather. However, single spacecraft measurements observed from the Earth have limitations in studying the structure and evolution of solar plasma as they are unable to differentiate spatial and temporal variations. To overcome this limitation and improve our understanding of interplanetary scintillation, we simultaneously observed radio signals transmitted by two co-orbiting spacecraft: the ESA Mars Express (MEX) and the Chinese National Space Administration Tianwen-1 (TIW-1). We conducted the observations from April to November 2021 using the University of Tasmania’s VLBI radio telescopes at 8.4 GHz. We employed the Planetary Radio Interferometer and Doppler Experiment (PRIDE) technique to determine the topocentric Doppler measurements and residual phase of the carrier signal. These observables were used to quantify the phase fluctuations of the spacecraft signals caused by solar wind and hydrodynamic turbulence in the interplanetary medium. The measured phase fluctuations RMS from both spacecraft show small differences which are caused by factors such as the spacecraft’s motion, onboard electronics, and variations in the uplink signal path through Earth’s ionosphere. These fluctuations decrease with solar elongation and correlate with solar radio flux at 10.7 cm (2800 MHz), indicating solar activity. The estimated total electron contents along MEX and TIW-1’s radio lines of sight are similar, with higher values at lower solar elongations. Simultaneous multi-spacecraft observations also enable RFI characterization, frequent spacecraft performance comparisons, and investigation of solar activity effects on spacecraft performance and scientific outcomes.
- 7 March 2025
- Published by Springer Nature in Experimental Astronomy
- Vol. 59 (2) , 1-21
Open AccessSimultaneous multi-spacecraft observations with VLBI radio telescopes to study the interplanetary phase scintillation
Ground-based observations of spacecraft signals have been used to study space weather. However, single spacecraft measurements observed from the Earth have limitations in studying the structure and evolution of solar plasma as they are unable to differentiate spatial and temporal variations. To overcome this limitation and improve our understanding of interplanetary scintillation, we simultaneously observed radio signals transmitted by two co-orbiting spacecraft: the ESA Mars Express (MEX) and the Chinese National Space Administration Tianwen-1 (TIW-1). We conducted the observations from April to November 2021 using the University of Tasmania’s VLBI radio telescopes at 8.4 GHz. We employed the Planetary Radio Interferometer and Doppler Experiment (PRIDE) technique to determine the topocentric Doppler measurements and residual phase of the carrier signal. These observables were used to quantify the phase fluctuations of the spacecraft signals caused by solar wind and hydrodynamic turbulence in the interplanetary medium. The measured phase fluctuations RMS from both spacecraft show small differences which are caused by factors such as the spacecraft’s motion, onboard electronics, and variations in the uplink signal path through Earth’s ionosphere. These fluctuations decrease with solar elongation and correlate with solar radio flux at 10.7 cm (2800 MHz), indicating solar activity. The estimated total electron contents along MEX and TIW-1’s radio lines of sight are similar, with higher values at lower solar elongations. Simultaneous multi-spacecraft observations also enable RFI characterization, frequent spacecraft performance comparisons, and investigation of solar activity effects on spacecraft performance and scientific outcomes.
- Open Access
- 9 September 2024
- Published by Springer Nature in CEAS Space Journal
- Vol. 17 (3) , 339-359
Planetary radio interferometry and Doppler experiment as an operational component of the Jupiter Icy Moons Explorer mission
We present an overview of the operations and engineering interface for Planetary Radio Interferometry and Doppler Experiment (PRIDE) radio astronomy observations as a scientific component of the ESA’s Jupiter Icy Moons Explorer (JUICE) mission, as well as other prospective planetary and space science missions. The article discusses advanced scheduling and planning methods that make it possible to create observing schedules for observations of specific spacecraft in concurrence with observations of natural radio sources. In order to put this into practice and find suitable natural background calibrator sources for PRIDE of JUICE mission, we developed planning and scheduling software. The conventional scheduling software for natural celestial radio sources is not set up to include spacecraft as observation targets in the necessary control files. Therefore, difficulties already arise during observation planning. We report on the development of new and the adaptation of existing routines used in astrophysical and geodetic VLBI for satellite scheduling and planning. The analysis of the PRIDE science observations led to improved observational planning, and the mission’s scheduling methodologies were studied using a systems engineering approach. In addition, we highlighted the new procedures, like finding charts for selecting calibrator radio sources over a range of frequency bands and the outcomes of those strategies for science operation planning. A simulation of the flyby of Venus during the cruise phase of the JUICE spacecraft, based on the Tudat software, is also presented, resulting in a promising opportunity to test PRIDE techniques and evaluate the improvements that PRIDE observables can make to natural bodies’ ephemerides. The first $$\hbox {K}_{a}$$ -band (32 GHz) observations of the ESA’s BepiColombo by a radio telescope in the VLBI network, which employs a similar radio communications system as JUICE, were also demonstrated as a test case. The primary objective of these activities is to serve as a practice run for the upcoming operational PRIDE JUICE operations. We showcase the capabilities of the planning and scheduling software for other space missions.- 9 September 2024
- Published by Springer Nature in CEAS Space Journal
- Vol. 17 (3) , 339-359
Open AccessPlanetary radio interferometry and Doppler experiment as an operational component of the Jupiter Icy Moons Explorer mission
We present an overview of the operations and engineering interface for Planetary Radio Interferometry and Doppler Experiment (PRIDE) radio astronomy observations as a scientific component of the ESA’s Jupiter Icy Moons Explorer (JUICE) mission, as well as other prospective planetary and space science missions. The article discusses advanced scheduling and planning methods that make it possible to create observing schedules for observations of specific spacecraft in concurrence with observations of natural radio sources. In order to put this into practice and find suitable natural background calibrator sources for PRIDE of JUICE mission, we developed planning and scheduling software. The conventional scheduling software for natural celestial radio sources is not set up to include spacecraft as observation targets in the necessary control files. Therefore, difficulties already arise during observation planning. We report on the development of new and the adaptation of existing routines used in astrophysical and geodetic VLBI for satellite scheduling and planning. The analysis of the PRIDE science observations led to improved observational planning, and the mission’s scheduling methodologies were studied using a systems engineering approach. In addition, we highlighted the new procedures, like finding charts for selecting calibrator radio sources over a range of frequency bands and the outcomes of those strategies for science operation planning. A simulation of the flyby of Venus during the cruise phase of the JUICE spacecraft, based on the Tudat software, is also presented, resulting in a promising opportunity to test PRIDE techniques and evaluate the improvements that PRIDE observables can make to natural bodies’ ephemerides. The first $$\hbox {K}_{a}$$ -band (32 GHz) observations of the ESA’s BepiColombo by a radio telescope in the VLBI network, which employs a similar radio communications system as JUICE, were also demonstrated as a test case. The primary objective of these activities is to serve as a practice run for the upcoming operational PRIDE JUICE operations. We showcase the capabilities of the planning and scheduling software for other space missions. - Open Access
Planetary radio interferometry and Doppler experiment as an operational component of the Jupiter Icy Moons Explorer mission
We present an overview of the operations and engineering interface for Planetary Radio Interferometry and Doppler Experiment (PRIDE) radio astronomy observations as a scientific component of the ESA s Jupiter Icy Moons Explorer (JUICE) mission, as well as other prospective planetary and space science missions. The article discusses advanced scheduling and planning methods that make it possible to create observing schedules for observations of specific spacecraft in concurrence with observations of natural radio sources. In order to put this into practice and find suitable natural background calibrator sources for PRIDE of JUICE mission, we developed planning and scheduling software. The conventional scheduling software for natural celestial radio sources is not set up to include spacecraft as observation targets in the necessary control files. Therefore, difficulties already arise during observation planning. We report on the development of new and the adaptation of existing routines used in astrophysical and geodetic VLBI for satellite scheduling and planning. The analysis of the PRIDE science observations led to improved observational planning, and the mission s scheduling methodologies were studied using a systems engineering approach. In addition, we highlighted the new procedures, like finding charts for selecting calibrator radio sources over a range of frequency bands and the outcomes of those strategies for science operation planning. A simulation of the flyby of Venus during the cruise phase of the JUICE spacecraft, based on the Tudat software, is also presented, resulting in a promising opportunity to test PRIDE techniques and evaluate the improvements that PRIDE observables can make to natural bodies ephemerides.
Open AccessPlanetary radio interferometry and Doppler experiment as an operational component of the Jupiter Icy Moons Explorer mission
We present an overview of the operations and engineering interface for Planetary Radio Interferometry and Doppler Experiment (PRIDE) radio astronomy observations as a scientific component of the ESA s Jupiter Icy Moons Explorer (JUICE) mission, as well as other prospective planetary and space science missions. The article discusses advanced scheduling and planning methods that make it possible to create observing schedules for observations of specific spacecraft in concurrence with observations of natural radio sources. In order to put this into practice and find suitable natural background calibrator sources for PRIDE of JUICE mission, we developed planning and scheduling software. The conventional scheduling software for natural celestial radio sources is not set up to include spacecraft as observation targets in the necessary control files. Therefore, difficulties already arise during observation planning. We report on the development of new and the adaptation of existing routines used in astrophysical and geodetic VLBI for satellite scheduling and planning. The analysis of the PRIDE science observations led to improved observational planning, and the mission s scheduling methodologies were studied using a systems engineering approach. In addition, we highlighted the new procedures, like finding charts for selecting calibrator radio sources over a range of frequency bands and the outcomes of those strategies for science operation planning. A simulation of the flyby of Venus during the cruise phase of the JUICE spacecraft, based on the Tudat software, is also presented, resulting in a promising opportunity to test PRIDE techniques and evaluate the improvements that PRIDE observables can make to natural bodies ephemerides.
- Open Access
- 8 August 2024
- Published by Springer Nature in Space Science Reviews
- Vol. 220 (5) , 1-94
Characterization of the Surfaces and Near-Surface Atmospheres of Ganymede, Europa and Callisto by JUICE
We present the state of the art on the study of surfaces and tenuous atmospheres of the icy Galilean satellites Ganymede, Europa and Callisto, from past and ongoing space exploration conducted with several spacecraft to recent telescopic observations, and we show how the ESA JUICE mission plans to explore these surfaces and atmospheres in detail with its scientific payload. The surface geology of the moons is the main evidence of their evolution and reflects the internal heating provided by tidal interactions. Surface composition is the result of endogenous and exogenous processes, with the former providing valuable information about the potential composition of shallow subsurface liquid pockets, possibly connected to deeper oceans. Finally, the icy Galilean moons have tenuous atmospheres that arise from charged particle sputtering affecting their surfaces. In the case of Europa, plumes of water vapour have also been reported, whose phenomenology at present is poorly understood and requires future close exploration. In the three main sections of the article, we discuss these topics, highlighting the key scientific objectives and investigations to be achieved by JUICE. Based on a recent predicted trajectory, we also show potential coverage maps and other examples of reference measurements. The scientific discussion and observation planning presented here are the outcome of the JUICE Working Group 2 (WG2): “Surfaces and Near-surface Exospheres of the Satellites, dust and rings”.
- 8 August 2024
- Published by Springer Nature in Space Science Reviews
- Vol. 220 (5) , 1-94
Open AccessCharacterization of the Surfaces and Near-Surface Atmospheres of Ganymede, Europa and Callisto by JUICE
We present the state of the art on the study of surfaces and tenuous atmospheres of the icy Galilean satellites Ganymede, Europa and Callisto, from past and ongoing space exploration conducted with several spacecraft to recent telescopic observations, and we show how the ESA JUICE mission plans to explore these surfaces and atmospheres in detail with its scientific payload. The surface geology of the moons is the main evidence of their evolution and reflects the internal heating provided by tidal interactions. Surface composition is the result of endogenous and exogenous processes, with the former providing valuable information about the potential composition of shallow subsurface liquid pockets, possibly connected to deeper oceans. Finally, the icy Galilean moons have tenuous atmospheres that arise from charged particle sputtering affecting their surfaces. In the case of Europa, plumes of water vapour have also been reported, whose phenomenology at present is poorly understood and requires future close exploration. In the three main sections of the article, we discuss these topics, highlighting the key scientific objectives and investigations to be achieved by JUICE. Based on a recent predicted trajectory, we also show potential coverage maps and other examples of reference measurements. The scientific discussion and observation planning presented here are the outcome of the JUICE Working Group 2 (WG2): “Surfaces and Near-surface Exospheres of the Satellites, dust and rings”.