Malcolm Pitts
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Malcolm Pitts has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Atheer A. Al-Fadhli
Kuwait Oil Company
1 shared publication- C. Colliver
Carnegie Mellon University 4400 Fifth Avenue, Pittsburgh, Pennsylvania 15213, United States
1 shared publication Dawood S. Kamal
Kuwait Oil Company
1 shared publicationElio Dean
Surtek, Inc
1 shared publication- Francesca A. Starvaggi
Department of Chemistry, Stanford University, Stanford, CA 94305, USA
1 shared publication - Karoline E. Eckhart
Department of Chemistry, Carnegie Mellon University, Pittsburgh, USA
1 shared publication
Latest Publications
- 20 September 2021
- Published by American Chemical Society (ACS) in Journal of Chemical Education
- Vol. 98 (10) , 3153-3162
Hands-On Laboratory Experience Using Adhesives for Remote Learning of Polymer Chemistry
- 20 September 2021
- Published by American Chemical Society (ACS) in Journal of Chemical Education
- Vol. 98 (10) , 3153-3162
Hands-On Laboratory Experience Using Adhesives for Remote Learning of Polymer Chemistry
- 13 October 2019
- Published by Society of Petroleum Engineers (SPE)
Insights on Single Well Chemical Tracer Testing Beyond Oil Saturation Changes
Single Well Chemical Tracer Testing (SWCTT) is traditionally performed to determine oil saturation after waterflooding and after enhanced oil recovery techniques. Raudhatain Lower Burgan (RALB) and Sabriyah Lower Burgan (SALB) SWCTT oil saturation reduction due to injection of surfactant-polymer and alkali-surfactant solutions, respectively, were 7 and 8% OOIP, respectively. During SWCTT, injection rate and surface pressure are routinely measured for each injected solution. Injection rate and surface pressure permit additional determinations to be made as outlined below: Pseudo resistance factor to any fluid "i" can be calculated and, from this, changes in injectivity can be determined Flowing viscosity of injected fluids relative to water Effective permeability to injected fluids Injectivity factors Pseudo resistance factor for RALB continually increased with seawater injection, from 0.5 to 1.0 indicating a reduction of kwro to approximately half and a twofold loss of injectivity. SALB kwro showed a three-fold loss of injectivity with seawater injection (pseudo resistance factor increased to 1.0 from 0.36). RALB pseudo residual resistance factor was 6.0 indicating a six-fold loss of injectivity due to surfactant-polymer and polymer drive solution injection even though the oil saturation was reduced by 7% OOIP. SALB pseudo resistance factor increased to 1.7 during alkaline-surfactant solution, indicating a loss of injectivity and an increase in flowing viscosity. SALB pseudo residual resistance factors were 0.89 to 1.06 suggesting no damage to reservoir rock and no loss to a slight increase of injectivity or an increase of kwro after an 8% OOIP saturation reduction. RALB surfactant-polymer rheometer viscosity was 0.55 cP while flowing viscosity was 0.21 cP as calculated from pseudo resistance factor data with the comparative polymer drive solution viscosities being 1.9 cP rheometer and 0.16 cP flowing. SALB alkaline-surfactant solution flowing viscosity was calculated to be 0.80 cP compared to water viscosity of 0.50 cP. Calculated SALB kwro values for injection of water, alkaline-surfactant, and water flush after alkaline-surfactant are 0.012, 0.007, and 0.011 to 0.015mD, respectively. Calculated RALB kwro values for injection of seawater and seawater flush after surfactant-polymer/polymer flush are 0.019 and 0.004 mD.
- 13 October 2019
- Published by Society of Petroleum Engineers (SPE)
Insights on Single Well Chemical Tracer Testing Beyond Oil Saturation Changes
Single Well Chemical Tracer Testing (SWCTT) is traditionally performed to determine oil saturation after waterflooding and after enhanced oil recovery techniques. Raudhatain Lower Burgan (RALB) and Sabriyah Lower Burgan (SALB) SWCTT oil saturation reduction due to injection of surfactant-polymer and alkali-surfactant solutions, respectively, were 7 and 8% OOIP, respectively. During SWCTT, injection rate and surface pressure are routinely measured for each injected solution. Injection rate and surface pressure permit additional determinations to be made as outlined below: Pseudo resistance factor to any fluid "i" can be calculated and, from this, changes in injectivity can be determined Flowing viscosity of injected fluids relative to water Effective permeability to injected fluids Injectivity factors Pseudo resistance factor for RALB continually increased with seawater injection, from 0.5 to 1.0 indicating a reduction of kwro to approximately half and a twofold loss of injectivity. SALB kwro showed a three-fold loss of injectivity with seawater injection (pseudo resistance factor increased to 1.0 from 0.36). RALB pseudo residual resistance factor was 6.0 indicating a six-fold loss of injectivity due to surfactant-polymer and polymer drive solution injection even though the oil saturation was reduced by 7% OOIP. SALB pseudo resistance factor increased to 1.7 during alkaline-surfactant solution, indicating a loss of injectivity and an increase in flowing viscosity. SALB pseudo residual resistance factors were 0.89 to 1.06 suggesting no damage to reservoir rock and no loss to a slight increase of injectivity or an increase of kwro after an 8% OOIP saturation reduction. RALB surfactant-polymer rheometer viscosity was 0.55 cP while flowing viscosity was 0.21 cP as calculated from pseudo resistance factor data with the comparative polymer drive solution viscosities being 1.9 cP rheometer and 0.16 cP flowing. SALB alkaline-surfactant solution flowing viscosity was calculated to be 0.80 cP compared to water viscosity of 0.50 cP. Calculated SALB kwro values for injection of water, alkaline-surfactant, and water flush after alkaline-surfactant are 0.012, 0.007, and 0.011 to 0.015mD, respectively. Calculated RALB kwro values for injection of seawater and seawater flush after surfactant-polymer/polymer flush are 0.019 and 0.004 mD.