Long Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Long Zhou has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Hong-Shuang Li
College of Aerospace Engineering Nanjing University of Aeronautics and Astronautics Nanjing China
1 shared publication Shuhua Zhu
Nanjing University of Aeronautics and Astronautics, Nanjing, China
1 shared publication- Shuhua Zhu
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
1 shared publication - Wentao Yi
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
1 shared publication - Yuequan Wang
College of Material Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing, PR China
1 shared publication
Latest Publications
- Open Access
- 23 November 2022
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 360, 01084
Numerical study on fiber waviness defect and sensitivity analysis of the parameters
The presence of fiber waviness defects is well-known to reduce the compressive strength. A FE model was established and the results of failure load and mode were compared with the test results to demonstrate the validity and accuracy. The influence of two parameters L and offset Angle θ of fiber waviness defect was studied. The simulation results show that the compression failure load increases with the increasing of L at constant A/H for convex and concave fiber fold by 33.0% and 20.1% respectively, but there is no significant effect on the failure load with θ within 5%.
- 23 November 2022
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 360, 01084
Open AccessNumerical study on fiber waviness defect and sensitivity analysis of the parameters
The presence of fiber waviness defects is well-known to reduce the compressive strength. A FE model was established and the results of failure load and mode were compared with the test results to demonstrate the validity and accuracy. The influence of two parameters L and offset Angle θ of fiber waviness defect was studied. The simulation results show that the compression failure load increases with the increasing of L at constant A/H for convex and concave fiber fold by 33.0% and 20.1% respectively, but there is no significant effect on the failure load with θ within 5%.
- Open Access
Experimental and Numerical Study on the Compressive Failure of Composite Laminates with Fiber Waviness Defects
Fiber waviness defects are found in the inner surface of the hat-shaped stringers manufactured by a process system. In order to establish the acceptance criterion for the stringers with the fiber waviness defects, experimental testing and numerical simulation were carried out in this study. Specially induced fiber waviness defects of four pre-defined severity levels were manufactured and tested. A maximum of a 58.1% drop in compressive failure load is observed for the most severe level in the experimental results. A finite element model with progressive damage method and cohesive zone technique was developed to simulate the failure process and the impact of fiber waviness defects. The numerical simulation results of compressive failure load have a good agreement with experimental results qualitatively and quantitatively. In addition, two simple parameters, i.e., aspect ratio A/H and the number of plies with fiber waviness, are proposed to characterize the influence of the fiber waviness on the compressive failure load for the purpose of fast engineering quality checks.
Open AccessExperimental and Numerical Study on the Compressive Failure of Composite Laminates with Fiber Waviness Defects
Fiber waviness defects are found in the inner surface of the hat-shaped stringers manufactured by a process system. In order to establish the acceptance criterion for the stringers with the fiber waviness defects, experimental testing and numerical simulation were carried out in this study. Specially induced fiber waviness defects of four pre-defined severity levels were manufactured and tested. A maximum of a 58.1% drop in compressive failure load is observed for the most severe level in the experimental results. A finite element model with progressive damage method and cohesive zone technique was developed to simulate the failure process and the impact of fiber waviness defects. The numerical simulation results of compressive failure load have a good agreement with experimental results qualitatively and quantitatively. In addition, two simple parameters, i.e., aspect ratio A/H and the number of plies with fiber waviness, are proposed to characterize the influence of the fiber waviness on the compressive failure load for the purpose of fast engineering quality checks.