Zhende Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zhende Zhu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Bi Sun
Harbin Institute of Technology (Shenzhen), Shenzhen 518055, China
3 shared publications - Nan Wu
Reserch Center for Wind Engineering and Engineering Vibration, Guangzhou University, Guangzhou 510006, China
3 shared publications - Rui Chen
School of Civil and Environmental Engineering, Harbin Institute of Technology Shenzhen, Shenzhen 518055, China
3 shared publications - Yang Ping
PowerChina Eco-Environment Group Co., Ltd., Shenzhen 518102, China
3 shared publications Hong-Bo Li
Research Institute of Geotechnical Engineering, Hohai University, Nanjing, China
1 shared publicationJian-Fei Shang
Research Institute of Geotechnical Engineering, Hohai University, Nanjing, China
1 shared publication
Latest Publications
- Open Access
Study on Axial Tensile Strain Rate Effect on Concrete Based on Experimental Investigation and Numerical Simulation
The material of concrete is a three-phase composite material composed of an aggregate, a mortar and an interface transition zone (ITZ). Based on this characteristic, the axial tensile test of mortar, the interface and concrete specimens under intermediate strain rate was carried out in this paper. The sensitivity of these three materials to strain rate was compared and analyzed. The numerical simulation of the axial tension of the concrete materials was studied. The following conclusions are drawn: in the axial tension test, the rate of sensitivity of the specimen interface is the strongest. With the increase in strain rate, the tensile strength and elastic modulus of concrete specimens increase but the effect of the ITZ decreases. The low tensile strength of the ITZ leads to its failure in concrete. The parallel bond strain energy and the dissipated energy of specimens increase with the strain rate. When the strain rate is higher (greater than 1 × 10−2), the increase rate of the dissipated energy is greater than that of the parallel bond strain energy. The results of this research can provide the corresponding basis for the safety evaluation and the stability analysis of concrete engineering in the range of intermediate strain rate.
Open AccessStudy on Axial Tensile Strain Rate Effect on Concrete Based on Experimental Investigation and Numerical Simulation
The material of concrete is a three-phase composite material composed of an aggregate, a mortar and an interface transition zone (ITZ). Based on this characteristic, the axial tensile test of mortar, the interface and concrete specimens under intermediate strain rate was carried out in this paper. The sensitivity of these three materials to strain rate was compared and analyzed. The numerical simulation of the axial tension of the concrete materials was studied. The following conclusions are drawn: in the axial tension test, the rate of sensitivity of the specimen interface is the strongest. With the increase in strain rate, the tensile strength and elastic modulus of concrete specimens increase but the effect of the ITZ decreases. The low tensile strength of the ITZ leads to its failure in concrete. The parallel bond strain energy and the dissipated energy of specimens increase with the strain rate. When the strain rate is higher (greater than 1 × 10−2), the increase rate of the dissipated energy is greater than that of the parallel bond strain energy. The results of this research can provide the corresponding basis for the safety evaluation and the stability analysis of concrete engineering in the range of intermediate strain rate.
- Open Access
Research on Dynamic Strength and Inertia Effect of Concrete Materials Based on Large-Diameter Split Hopkinson Pressure Bar Test
The Split Hopkinson Pressure Bar (SHPB) test device is an important tool to study the dynamic characteristics of concrete materials. Inertial effect is one of the main factors that cause inaccurate results in SHPB tests of concrete materials. To solve this problem, Large-diameter SHPB tests on concrete and mortar were performed. A dynamic increase factor (DIF) model considering strain rate effect and inertia effect was established. This model provides a scientific reference for studying the dynamic mechanical properties of concrete materials. The experimental results indicate that the strain rate effect of concrete is more sensitive than that of mortar, but the inertia effect of mortar is more sensitive than that of concrete. Under the same strain rate, the energy utilization rate, average fragment size, and impact potentiality of mortar are higher than concrete.
Open AccessResearch on Dynamic Strength and Inertia Effect of Concrete Materials Based on Large-Diameter Split Hopkinson Pressure Bar Test
The Split Hopkinson Pressure Bar (SHPB) test device is an important tool to study the dynamic characteristics of concrete materials. Inertial effect is one of the main factors that cause inaccurate results in SHPB tests of concrete materials. To solve this problem, Large-diameter SHPB tests on concrete and mortar were performed. A dynamic increase factor (DIF) model considering strain rate effect and inertia effect was established. This model provides a scientific reference for studying the dynamic mechanical properties of concrete materials. The experimental results indicate that the strain rate effect of concrete is more sensitive than that of mortar, but the inertia effect of mortar is more sensitive than that of concrete. Under the same strain rate, the energy utilization rate, average fragment size, and impact potentiality of mortar are higher than concrete.
- Open Access
Dynamic Response of Rock-like Materials Based on SHPB Pulse Waveform Characteristics
Rock-like brittle materials under dynamic load will show more complex dynamic mechanical properties than those under static load. The relationship between pulse waveform characteristics and strain rate effect and inertia effect is rarely discussed in the split-Hopkinson pressure bar (SHPB) numerical simulation research. In response to this problem, this paper discusses the effects of different pulse types and pulse waveforms on the incident waveform and dynamic response characteristics of specimens based on particle flow code (PFC). The research identifies a critical interval of rock dynamic strength, where the dynamic strength of the specimen is independent of the strain rate but increases with the amplitude of the incident stress wave. When the critical interval is exceeded, the dynamic strength is determined by the strain rate and strain rate gradient. The strain rate of the specimen is only related to the slope of the incident stress wave and is independent of its amplitude. It is also determined that the inertia effect cannot be eliminated in the SHPB. The slope of the velocity pulse waveform determines the strain rate of the specimen, the slope of the force pulse waveform determines the strain rate gradient of the specimen, and the upper bottom time determines the strain rate of the specimen. It provides a reference for SHPB numerical simulation. A dynamic strength prediction model of rock-like materials is then proposed, which considers the effects of strain rate and strain rate gradient.
Open AccessDynamic Response of Rock-like Materials Based on SHPB Pulse Waveform Characteristics
Rock-like brittle materials under dynamic load will show more complex dynamic mechanical properties than those under static load. The relationship between pulse waveform characteristics and strain rate effect and inertia effect is rarely discussed in the split-Hopkinson pressure bar (SHPB) numerical simulation research. In response to this problem, this paper discusses the effects of different pulse types and pulse waveforms on the incident waveform and dynamic response characteristics of specimens based on particle flow code (PFC). The research identifies a critical interval of rock dynamic strength, where the dynamic strength of the specimen is independent of the strain rate but increases with the amplitude of the incident stress wave. When the critical interval is exceeded, the dynamic strength is determined by the strain rate and strain rate gradient. The strain rate of the specimen is only related to the slope of the incident stress wave and is independent of its amplitude. It is also determined that the inertia effect cannot be eliminated in the SHPB. The slope of the velocity pulse waveform determines the strain rate of the specimen, the slope of the force pulse waveform determines the strain rate gradient of the specimen, and the upper bottom time determines the strain rate of the specimen. It provides a reference for SHPB numerical simulation. A dynamic strength prediction model of rock-like materials is then proposed, which considers the effects of strain rate and strain rate gradient.
- 7 September 2010
- Published by Springer Nature in Journal of Coal Science and Engineering (China)
- Vol. 16 (3) , 235-239
Research on the mining roadway displacement forecasting based on support vector machine theory
- 7 September 2010
- Published by Springer Nature in Journal of Coal Science and Engineering (China)
- Vol. 16 (3) , 235-239
Research on the mining roadway displacement forecasting based on support vector machine theory