Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mikko Iljana has a total of 56 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Isothermal Reduction Behavior and Microstructural Evolution of Iron Ore Sinter Under Simulated Radial Blast Furnace Gas Atmospheres With Hydrogen Injection

    by Ahmed Abdelrahim, Sherif Hegazy, Mikko Iljana, Aki Koskela, Carmen van der Kroon, Timo Fabritius

    This study investigates the isothermal reduction behavior of commercial iron ore sinter (B2 = 1.94) under radial blast furnace gas atmospheres derived from an industrial reference campaign. Twelve conditions were examined in a TGA at 700, 900, and 1100 °C, covering center and wall radial positions for a base case and a hydrogen‐injection scenario (20 kg H 2 /tHM). Reduction degree, phase transformations, microstructure, porosity, and BET specific surface area were characterized. At 700 °C, reduction remained partial (23%–45%), dominated by wüstite. Above 900 °C, near‐complete reduction to metallic iron was achieved, with kinetics accelerated at 1100 °C. Hydrogen injection enhanced reduction rates at 900 and 1100 °C under both radial positions due to the higher diffusivity and reducing potential of H 2 , whereas at 700 °C, it slightly lowered the final reduction degree primarily due to a lower thermodynamic reduction potential from elevated H 2 O, with the formation of a dense iron layer acting as a possible contributor to diffusion resistance. Wall atmospheres consistently exhibited a slower reduction rate and lower final reduction degrees than center atmospheres. Reduction progressed from the sinter sample periphery inward, generating a porous metallic iron network at high temperatures. Upon complete reduction, the sinter samples exhibited an increased porosity up to 65%–69%, while the BET surface area decreased from 0.6 m 2 /g (700 °C) to 0.1 m 2 /g (1100 °C) due to pore coarsening and sintering. The results indicate that hydrogen injection can improve sinter reducibility under sufficiently high‐temperature BF‐derived gas atmospheres, while low‐temperature, high‐H 2 O conditions require careful control of local gas potential and heat balance.

  • Open Access

    Influence of Hydrogen Injection on the Isothermal Reduction of Iron Ore Pellets under Simulated Blast Furnace Conditions

    by Olli Vitikka, Mikko Iljana, Aki Koskela, Anne Heikkilä, Carmen van der Kroon, Timo Fabritius

    Cutting down CO2 emissions from blast furnace (BF) ironmaking is a critical area of research. Utilization of hydrogen as a reducing agent has been regarded as one of the most promising solutions to address this challenge. This study examined the impact of using hydrogen injection on the isothermal reduction of commercial iron ore pellets under conditions simulating the center and wall areas of a BF. The effect of distinct reducing conditions, influenced by the radial position within a BF and the amount of hydrogen injected, on the reducibility, swelling, cracking, and porosity of pellets was investigated. A high-temperature furnace with a thermogravimetric analyzer was utilized to simulate the atmospheres of CO–CO2–H2–H2O–N2 at 700, 900 and 1100 °C in 300-minute experiments. The changes in volume and porosity of the pellets were determined based on the results obtained using a gas pycnometer and manual measurement. The phase transformations were studied using microscopy and X-ray diffraction. The results show that the addition of hydrogen had an accelerating effect on the reduction rates excluding the experiment conducted at 700 °C under center conditions of a BF, during which the high level of water vapor led to oxidation of the pellet on the surface rather than reduction at the beginning of the wüstite–metallic iron reduction stage. Furthermore, the pellets swelled less in hydrogen-enriched atmospheres. Also, it should be highlighted that the reduction was significantly faster near the center of a BF compared to the areas near the walls.


  • Open Access

    Reduction of Basic Iron Ore Sinter under Blast Furnace Wall and Center‐Simulated Conditions in CO–CO2–H2–H2O–N2 Gas

    by Ahmed Abdelrahim, Mikko Iljana, Matti Aula, Timo Fabritius

    This study examines how varying conditions at the center and wall of a blast furnace (BF) impact the reduction of iron ore sinter in a gas containing hydrogen and water vapor. Sinter samples are isothermally reduced at 700–1100 °C using a BF simulator to assess reduction rates and extent. Characterization techniques analyze the reduced samples’ mineralogical, physical, and microstructural changes. Results indicate that metallic iron formed at 700 °C in samples reduced under BF center conditions but is absent up to 900 °C in BF wall conditions. Metallic iron is initially formed at the periphery and propagated inward as temperature increased. The sinter's non‐homogeneous structure hinders uniform gas diffusion, with unfused iron ore content obstructing reducibility. The skeletal density of reduced samples correlated with the degree of reduction. The reduction of magnetite to metallic iron through wüstite is observed. Wüstite reducibility was better than calcium ferrite. No carbon deposition is observed in all testing conditions. Comparisons to acid iron ore pellets suggest charging the sinter to the BF center and pellets to the wall, with a recommendation to minimize unfused iron ore in the sinter charge for improved reducibility.


  • Open Access

    Effect of Biocarbon Addition on Metallurgical Properties of Mill Scale-Based Auger Pressing Briquettes

    by Olli Vitikka, Mikko Iljana, Anne Heikkilä, Illia Tkalenko, Oleksii Kovtun, Nikita Koriuchev, Daniel Shehovsov, Timo Fabritius

    This work focused on the usage of bio-based and secondary iron and steelmaking raw materials. Auger pressing briquettes, cold-bonded agglomerates made from by-products, mainly mill scale (80%), were successfully tested in industrial-scale blast furnace (BF) trials. The briquettes from industrial production were studied in two different laboratory-scale reduction experiments to compare them to laboratory-made briquettes. A blast furnace simulator (BFS) device was utilized in the simulations mimicking the temperature and gas profiles of an actual BF process. A reduction under load (RUL) device enabled the simulation of the physical load under reducing conditions. To determine how the high-temperature properties of the self-reducing briquettes depend on the amount of biocarbon, a bio-based reducing agent (2–10 %) was added to the laboratory-scale briquettes that already contained 5.6% total carbon mainly originating from BF dust. For the recipes studied, a weight loss of about 30% under reducing conditions leads to the disintegration of a briquette under load. Based on the BFS experiments, adding biocarbon to the recipe was profitable in terms of a self-reducing effect up to 6% when the total carbon content was 11%. The RUL experiments showed that the structure of the briquette became extremely plastic with the addition of 4% biocarbon which covers 39% of the total carbon contained in the briquette. This was the upper limit for biocarbon addition due to telescoping and disintegration followed by the formation of fines. The industrial briquettes used in the BF corresponded well to the laboratory-made briquettes in terms of metallurgical properties.


  • Open Access

    Suitability of Auger Pressing Briquettes for Blast Furnace Use Based on Laboratory Tests

    by Olli Vitikka, Mikko Iljana, Anne Heikkilä, Illia Tkalenko, Nikita Koriuchev, Daniel Shehovsov, Andrey Malkki, Timo Fabritius

    Briquetting is a process in which fine materials unsuitable for use as such are agglomerated to achieve a larger particle size. Auger pressing is a novel briquetting method to efficiently improve the recycling of by-products from iron and steelmaking. The high-temperature properties of auger pressing briquettes mainly consisting of blast furnace sludge and mill scale were evaluated. The aim was to determine the suitability of the briquettes for blast furnace (BF) ironmaking by studying the reduction, swelling, and cracking behavior using a laboratory-scale furnace. The blast furnace simulator (BFS) capable of performing non-isothermal reduction experiments with changing gas compositions was used to simulate the different stages of reduction up to 1100 °C in an atmosphere with N2, CO, and CO2 gases. A commercial olivine pellet and a conventional industrial BF briquette were used as reference samples. The sample weight losses were monitored by thermogravimetry, swelling as a change in the volume, and cracking by visual inspection. The samples were analyzed using microscopes and an elemental analyzer. Based on the BFS experiments, the briquettes proved to be a promising raw material for BF use. They were of a self-reducing quality due to their carbon content and showed reduction to metallic iron faster compared to the reference samples. The swelling was slight, and despite the minor cracking the structure of the briquettes did not degrade.


  • Open Access

    Reduction of Acid Iron Ore Pellets under Simulated Wall and Center Conditions in a Blast Furnace Shaft

    by Mikko Iljana, Ahmed Abdelrahim, Hauke Bartusch, Timo Fabritius

    The operational conditions, including temperature and gas composition, vary along the radial position in a blast furnace. Nevertheless, very few studies can be found in the literature that discuss how the reduction behavior of the ferrous burden varies along the radial position. In this study, the effect of the radial charging position on the reducibility of acid iron ore pellets was investigated using a laboratory-scale, high-temperature furnace in CO-CO2-N2 and CO-CO2-H2-H2O-N2 atmospheres up to 1100 °C. The experimental conditions were accumulated based on earlier measurements from a multi-point vertical probing campaign that was performed for a center-working European blast furnace. The main finding of this study is that the pellet reduction proceeded faster under simulated blast furnace conditions resembling those in the center area, compared to the wall area, because of a higher share of CO and H2 in the gas. Therefore, the pellet charging position affects its reduction path in a blast furnace. Additionally, it was shown that the presence of H2 and H2O in the reducing gas enhanced the progress of reduction reactions significantly and enhanced the formation of cracks slightly, both of which are desirable in blast furnace operation. The reducibility data attained in this study are important in understanding how temperature and gas composition is connected to the reduction degree under realistic process conditions.


  • Open Access

    Development of Cold-Bonded Briquettes Using By-Product-Based Ettringite Binder from Ladle Slag

    by Ahmed Abdelrahim, Hoang Nguyen, Mamdouh Omran, Paivo Kinnunen, Mikko Iljana, Mirja Illikainen, Timo Fabritius

    The recycling of steel plant side streams through cold-bonded briquettes has become quite common. However, Portland cement is mainly used as a binder in the briquettes, contributing significantly to the energy consumption, costs, and carbon footprint associated with the production of cold-bonded briquettes. This paper reports on a more sustainable method for side stream recycling that involves replacing cement with an ettringite-based binder. Ettringite binders develop early high strength and mainly consist of ladle slag, another side stream of the industry. Here, the ettringite-based binder is assessed in terms of its mechanical and thermal properties against a reference briquette made using the conventional technique. Three different briquette types are produced using several side stream materials and varying ettringite-based binder content. Briquettes produced using 15% and higher ettringite-based binder content exhibited excellent mechanical properties within a shorter curing period compared to conventional used binder. Moreover, the ettringite-based binder briquettes exhibited a better swelling behavior to conventional cement briquettes under conditions simulating a blast furnace. Graphical Abstract


  • Open Access

    Effect of Iron Ore Pellet Size on Metallurgical Properties

    by Mikko Iljana, Timo Paananen, Olli Mattila, Mikhail Kondrakov, Timo Fabritius

    Iron ore pellets are small and hard spherical particles agglomerated from a fine iron ore concentrate. They are used in the blast furnace process to produce hot metal. The diameter of blast furnace pellets is usually between 8 and 16 mm. In this study, a batch of magnesia iron ore pellets was first sieved into particle sizes of 8–10 mm, 10–12.7 mm, 12.7–16 mm and 16–20 mm, and the four different size fractions were used to study the effect of pellet size on metallurgical properties. The metallurgical experiments showed a decrease both in reducibility under unconstrained conditions and in low-temperature reduction-disintegration but showed an increase in cold crushing strength as the pellet size increased. In the reduction-softening test, pellets sized 10–12.7 mm reached the highest final temperature and the highest reduction degree among the pellet samples of different sizes. Based on the implications drawn from this study, the amount of 10–12.7 mm pellets should be maximized in a blast furnace operation.


  • Top Cited Papers
    Open Access

    A Review on the Kinetics of Iron Ore Reduction by Hydrogen

    by Aidin Heidari, Niusha Niknahad, Mikko Iljana, Timo Fabritius

    A clean energy revolution is occurring across the world. As iron and steelmaking have a tremendous impact on the amount of CO2 emissions, there is an increasing attraction towards improving the green footprint of iron and steel production. Among reducing agents, hydrogen has shown a great potential to be replaced with fossil fuels and to decarbonize the steelmaking processes. Although hydrogen is in great supply on earth, extracting pure H2 from its compound is costly. Therefore, it is crucial to calculate the partial pressure of H2 with the aid of reduction reaction kinetics to limit the costs. This review summarizes the studies of critical parameters to determine the kinetics of reduction. The variables considered were temperature, iron ore type (magnetite, hematite, goethite), H2/CO ratio, porosity, flow rate, the concentration of diluent (He, Ar, N2), gas utility, annealing before reduction, and pressure. In fact, increasing temperature, H2/CO ratio, hydrogen flow rate and hematite percentage in feed leads to a higher reduction rate. In addition, the controlling kinetics models and the impact of the mentioned parameters on them investigated and compared, concluding chemical reaction at the interfaces and diffusion of hydrogen through the iron oxide particle are the most common kinetics controlling models.


  • Suitability of Self‐Reducing and Slag‐Forming Briquettes for Electric Arc Furnace Use Based on Laboratory Tests

    by Ahmed Abdelrahim, Matti Aula, Mikko Iljana, Thomas Willms, Thomas Echterhof, Stefan Steinlechner, Davide Mombelli, Carlo Mapelli, Mamdouh Omran, Stefan Preiss, et al.

    The in‐plant recycling routes of side streams produced in electric arc furnace (EAF) steelmaking remain underexplored. Briquetting is an attractive technique to enable their recycle. Briquettes introduced into EAF must possess certain mechanical and chemical properties. However, no standard is available to determine the suitability of briquettes used in the EAF process. Herein, eight side streams are characterized, and used to produce seven different briquettes to be used in EAF. Briquettes tested consist of four self‐reducing briquettes and three slag‐forming briquettes produced using different recipes. The briquettes are subjected to several mechanical and thermal tests which reflect their intended use in EAF. The mechanical tests include compression and drop tests, and the thermal tests include optical dilatometry, thermogravimetric analysis (TGA)–derivative thermogravimetry (DTG)–mass spectrometry (MS), and full‐scale briquette reduction tests. Moreover, melting trials are performed to assess the melting behavior of selected briquettes and their interaction with slag. Suitability of briquettes characteristics is assessed based on values from the literature and against reference ferroalloys and lime stones used in one of the steel plants. Two briquettes are deemed suitable for EAF use, while three briquettes are deemed unsuitable, and two briquettes are considered of limited use.