Jingxiong Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jingxiong Chen has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Hong Wang
South China University of Technology
10 shared publications - Jian Qin
School of Electronics and Communication Engineering, Guangzhou University, Guangzhou, China
4 shared publications Xiaoyi Liu
School of Electronic and Information Engineering, South China University of Technology, Guangzhou, China
4 shared publications- Xiao Ma
Engineering Research Center for Optoelectronics of Guangdong Province, School of Physics and Optoelectronics, South China University of Technology, Guangzhou, China
3 shared publications Yuanxi Jiang
Engineering Research Center for Optoelectronics of Guangdong Province, School of Physics and Optoelectronics, South China University of Technology, Guangzhou, China
3 shared publications- Quanbin Zhou
Engineering Research Center for Optoelectronics of Guangdong Province, School of Electronics and Information Engineering, South China University of Technology, Guangzhou, China
2 shared publications
Latest Publications
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (9) , 1388-1391
AlGaN/GaN HEMTs on Si by Self-Aligned TaN Contact Ledge for Low-Voltage RF Applications
We propose a self-aligned contact ledge structure to achieve the small ohmic contact resistance ( $R_{\text {c}}$ ) of GaN-based high electron mobility transistors (HEMTs) on Si for low-voltage RF applications. Without additional photolithography processes, the ledge structure is achieved by magnetron sputtering with good particle filling on the sidewall. Due to the good coverage of sputtered Ta, the self-aligned TaN contact ledge not only has a clear boundary after high-temperature annealing but also introduces an additional current path to reduce on-resistance ( ${R} _{\text {on}}$ ), which is important for fabricating devices for low-voltage RF applications. Benefiting from the contact ledge structure and the low sheet resistance high Al component Al0.6Ga0.4N/GaN epitaxy, a low ${R} _{\text {on}}$ of $1.12~\Omega \cdot $ mm is obtained and the peak transconductance increased by 13%. At 3.5 GHz and operating voltage 5 V, the power-added efficiency (PAE) is 67.0% and the output power density ( ${P} _{\text {out}}$ ) is 0.75 W/mm. The PAE is 8.5% higher than that of noncontact ledge.
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (9) , 1388-1391
AlGaN/GaN HEMTs on Si by Self-Aligned TaN Contact Ledge for Low-Voltage RF Applications
We propose a self-aligned contact ledge structure to achieve the small ohmic contact resistance ( $R_{\text {c}}$ ) of GaN-based high electron mobility transistors (HEMTs) on Si for low-voltage RF applications. Without additional photolithography processes, the ledge structure is achieved by magnetron sputtering with good particle filling on the sidewall. Due to the good coverage of sputtered Ta, the self-aligned TaN contact ledge not only has a clear boundary after high-temperature annealing but also introduces an additional current path to reduce on-resistance ( ${R} _{\text {on}}$ ), which is important for fabricating devices for low-voltage RF applications. Benefiting from the contact ledge structure and the low sheet resistance high Al component Al0.6Ga0.4N/GaN epitaxy, a low ${R} _{\text {on}}$ of $1.12~\Omega \cdot $ mm is obtained and the peak transconductance increased by 13%. At 3.5 GHz and operating voltage 5 V, the power-added efficiency (PAE) is 67.0% and the output power density ( ${P} _{\text {out}}$ ) is 0.75 W/mm. The PAE is 8.5% higher than that of noncontact ledge.
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7326-7333
Optimal Thermal Resistance Model of GaN HEMTs Considering Thickness-Dependent Thermal Conductivity
We propose a thermal resistance model for gallium nitride (GaN) high electron mobility transistor (HEMT) that considers the thickness-dependence and anisotropy of the thermal conductivity of GaN films to improve the calculation accuracy. In this study, the Debye–Callaway model is used to calculate the in-plane and cross-plane thermal conductivity of the GaN buffer layer as a function of layer thickness. An electrical model of heat generation profiles is established by using the technology computer-aided design (TCAD). The temperature distribution is predicted by the finite element methods (FEMs) simulations. We confirm that as the thickness of the GaN layer increases, the total thermal resistance on diamond, SiC, and Si substrates decreases first and then increases, reaching their minimum values at 3.6, 5, and 48 $\mu$ m at a thermal boundary resistance (TBR) of 30 m $^{\text{2}}\cdot \text{K/GW}$ , respectively. Moreover, there is a lack of research on the optimal GaN thickness of devices with different substrates. Based on this model, we investigate the effects of TBR, power dissipation level, and gate pitch values on the optimal GaN thickness of devices with different substrates (Si, SiC, and diamond).
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7326-7333
Optimal Thermal Resistance Model of GaN HEMTs Considering Thickness-Dependent Thermal Conductivity
We propose a thermal resistance model for gallium nitride (GaN) high electron mobility transistor (HEMT) that considers the thickness-dependence and anisotropy of the thermal conductivity of GaN films to improve the calculation accuracy. In this study, the Debye–Callaway model is used to calculate the in-plane and cross-plane thermal conductivity of the GaN buffer layer as a function of layer thickness. An electrical model of heat generation profiles is established by using the technology computer-aided design (TCAD). The temperature distribution is predicted by the finite element methods (FEMs) simulations. We confirm that as the thickness of the GaN layer increases, the total thermal resistance on diamond, SiC, and Si substrates decreases first and then increases, reaching their minimum values at 3.6, 5, and 48 $\mu$ m at a thermal boundary resistance (TBR) of 30 m $^{\text{2}}\cdot \text{K/GW}$ , respectively. Moreover, there is a lack of research on the optimal GaN thickness of devices with different substrates. Based on this model, we investigate the effects of TBR, power dissipation level, and gate pitch values on the optimal GaN thickness of devices with different substrates (Si, SiC, and diamond).
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (8) , 4867-4873
Investigation of DC and RF Characteristics of AlGaN/GaN HEMT With Various Planar Distributed Channel Division
We use a standard ion implantation process to fabricate planar distributed channel AlGaN/GaN high-electron-mobility transistors (HEMTs) on silicon. The process to achieve minimum 2- $\mu $ m microchannel structure is compatible with standard ion implantation for device isolation and suitable for mass production. The 2- $\mu $ m microchannel device shows significant improvements in thermal control and dc performance without an increase in the process complexity. The simulation and experimental results show that the smaller the channel division is, the lower the channel temperature and the smaller the saturated current decrease are due to less self-heating effect. Compared to conventional devices, devices with 2- $\mu $ m microchannel show a 30 $^{\circ}$ C decreased channel temperature and a 10% increased output current. If the microchannel width is further reduced, the extra parasitic gate capacitance increases rapidly, which may limit high-frequency applications.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (8) , 4867-4873
Investigation of DC and RF Characteristics of AlGaN/GaN HEMT With Various Planar Distributed Channel Division
We use a standard ion implantation process to fabricate planar distributed channel AlGaN/GaN high-electron-mobility transistors (HEMTs) on silicon. The process to achieve minimum 2- $\mu $ m microchannel structure is compatible with standard ion implantation for device isolation and suitable for mass production. The 2- $\mu $ m microchannel device shows significant improvements in thermal control and dc performance without an increase in the process complexity. The simulation and experimental results show that the smaller the channel division is, the lower the channel temperature and the smaller the saturated current decrease are due to less self-heating effect. Compared to conventional devices, devices with 2- $\mu $ m microchannel show a 30 $^{\circ}$ C decreased channel temperature and a 10% increased output current. If the microchannel width is further reduced, the extra parasitic gate capacitance increases rapidly, which may limit high-frequency applications.
- 4 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (5) , 2943-2949
Novel T-Shaped Gate With Air Gap for AlGaN/GaN HEMTs on Silicon With High Johnson’s Figures of Merit
We present high-performance AlGaN/GaN high-electron-mobility transistors (HEMTs) fabricated on a silicon substrate featuring a novel T-shaped gate. The incorporation of the air gap between the gate and the low-k passivation layer effectively reduces the gate capacitance and thus improves the RF characteristics of the device. The prepared device with a gate length of 180 nm has a unit current gain cutoff frequency ( ${f} _{{\text {T}}}$ ) of 55.2 GHz, a maximum oscillation frequency ( ${f}_{{\text {MAX}}}$ ) of 73.7 GHz, and a three-terminal OFF-state breakdown voltage ( $\text{B}{V} _{{\text {gd}}}$ ) of 143 V at the gate–drain distance of $2.2~\mu \text{m}$ . The estimated Johnson’s figure of merit (J-FOM = $\text{B}{V} _{{\text {gd}}} \times {f}_{{\text {T}}}$ ) is 7.9 THz $\cdot \text{V}$ , representing a significant 30% improvement in comparison to the device with only stacked passivation layers. Besides, the J-FOM surpasses that of the single HfO2 passivation and single SiO2 passivation devices by 64.6% and 58%, respectively. These results clearly indicate that the AlGaN/GaN HEMTs with novel T-shaped gate design have great potential for radio frequency (RF) power device applications.
- 4 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (5) , 2943-2949
Novel T-Shaped Gate With Air Gap for AlGaN/GaN HEMTs on Silicon With High Johnson’s Figures of Merit
We present high-performance AlGaN/GaN high-electron-mobility transistors (HEMTs) fabricated on a silicon substrate featuring a novel T-shaped gate. The incorporation of the air gap between the gate and the low-k passivation layer effectively reduces the gate capacitance and thus improves the RF characteristics of the device. The prepared device with a gate length of 180 nm has a unit current gain cutoff frequency ( ${f} _{{\text {T}}}$ ) of 55.2 GHz, a maximum oscillation frequency ( ${f}_{{\text {MAX}}}$ ) of 73.7 GHz, and a three-terminal OFF-state breakdown voltage ( $\text{B}{V} _{{\text {gd}}}$ ) of 143 V at the gate–drain distance of $2.2~\mu \text{m}$ . The estimated Johnson’s figure of merit (J-FOM = $\text{B}{V} _{{\text {gd}}} \times {f}_{{\text {T}}}$ ) is 7.9 THz $\cdot \text{V}$ , representing a significant 30% improvement in comparison to the device with only stacked passivation layers. Besides, the J-FOM surpasses that of the single HfO2 passivation and single SiO2 passivation devices by 64.6% and 58%, respectively. These results clearly indicate that the AlGaN/GaN HEMTs with novel T-shaped gate design have great potential for radio frequency (RF) power device applications.
- Open Access
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 104-112
Investigation of Electrical Property and Thermal Stability in Enhancement-Mode InxAl1–xN/AlN/GaN MOS-HEMTs Fabricated by Using NiOx Gate and Fluorine Treatment
in this study, we report a novel approach for achieving high-performance enhancement mode (E-mode) InAlN/GaN MOS HEMTs based on the fluorine treatment and a p-type NiOx gate (F-NiO HEMT). The NiO film was deposited at different substrate temperatures using reactive sputtering in a varied mixture of O2 and Ar. We show that the threshold voltage (VTH) is effectively modulated by comprehensively optimizing fluorine ion implantation and NiO sputtering conditions without requiring gate recess etching. The influence of different NiO deposition conditions on electrical properties and the critical interface of NiOx/InAlN have been investigated in detail. The proposed E-mode F-NiO HEMT exhibits superior on-state characteristics, including more positive VTH, enhanced gate voltage swing, larger transconductance gm and also superior gate control over the channel. The dual C-V and pulsed mode measurements confirm the excellent NiOx/AlInN interface and effective suppression of current collapse. We propose a model to explain the contrasting temperature-dependent coefficients of VTH shifts observed in pure fluorine ion-implanted and NiO-based devices. The underlying mechanisms at elevated temperatures are also analyzed.
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 104-112
Open AccessInvestigation of Electrical Property and Thermal Stability in Enhancement-Mode InxAl1–xN/AlN/GaN MOS-HEMTs Fabricated by Using NiOx Gate and Fluorine Treatment
in this study, we report a novel approach for achieving high-performance enhancement mode (E-mode) InAlN/GaN MOS HEMTs based on the fluorine treatment and a p-type NiOx gate (F-NiO HEMT). The NiO film was deposited at different substrate temperatures using reactive sputtering in a varied mixture of O2 and Ar. We show that the threshold voltage (VTH) is effectively modulated by comprehensively optimizing fluorine ion implantation and NiO sputtering conditions without requiring gate recess etching. The influence of different NiO deposition conditions on electrical properties and the critical interface of NiOx/InAlN have been investigated in detail. The proposed E-mode F-NiO HEMT exhibits superior on-state characteristics, including more positive VTH, enhanced gate voltage swing, larger transconductance gm and also superior gate control over the channel. The dual C-V and pulsed mode measurements confirm the excellent NiOx/AlInN interface and effective suppression of current collapse. We propose a model to explain the contrasting temperature-dependent coefficients of VTH shifts observed in pure fluorine ion-implanted and NiO-based devices. The underlying mechanisms at elevated temperatures are also analyzed.
- Open Access
- 13 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 11, 503-509
A Low Loss and High Selectivity GaN-on-Si On-Chip Bandpass Filter
We propose a low loss and high selectivity bandpass filter with defected structure on GaN-on-Silicon. GaN-on-Si exhibits a high insertion loss due to the presence of parasitic channels at the AlN/Si interface. It is necessary to strengthen the coupling between the resonators to achieve a low loss. However, this results in weaker suppression of adjacent channels and lower selectivity of frequencies. The designed filter consists of square spiral defect structure resonators and a step impedance resonator, which provides tunable transmission zero and facilitates the adjustment of pass band. With an interdigitated capacitor, at a frequency span from 3.3 to 4.9 GHz, the proposed filter has a low insertion loss of 2.71dB and improves the suppression of adjacent channel (5.8 GHz) by 11.2 dB compared to the traditional SIR filter. The out-of-band suppression of the filter is better than 15.93 dB at 20 GHz. Compared to the traditional SIR filter, the proposed filter achieves a steep transition zone, and an out-ofband rejection reduction by at least 6.6 dB.
- 13 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 11, 503-509
Open AccessA Low Loss and High Selectivity GaN-on-Si On-Chip Bandpass Filter
We propose a low loss and high selectivity bandpass filter with defected structure on GaN-on-Silicon. GaN-on-Si exhibits a high insertion loss due to the presence of parasitic channels at the AlN/Si interface. It is necessary to strengthen the coupling between the resonators to achieve a low loss. However, this results in weaker suppression of adjacent channels and lower selectivity of frequencies. The designed filter consists of square spiral defect structure resonators and a step impedance resonator, which provides tunable transmission zero and facilitates the adjustment of pass band. With an interdigitated capacitor, at a frequency span from 3.3 to 4.9 GHz, the proposed filter has a low insertion loss of 2.71dB and improves the suppression of adjacent channel (5.8 GHz) by 11.2 dB compared to the traditional SIR filter. The out-of-band suppression of the filter is better than 15.93 dB at 20 GHz. Compared to the traditional SIR filter, the proposed filter achieves a steep transition zone, and an out-ofband rejection reduction by at least 6.6 dB.
- Open Access
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 11, 130-134
Novel Stacked Passivation Structure for AlGaN/GaN HEMTs on Silicon With High Johnson’s Figures of Merit
We present a high-performance AlGaN/GaN high electron mobility transistors (HEMTs) on silicon substrate with novel stacked passivation layer (HfO2/SiO2). The stacked passivation structure can effectively modulate the electric field and reduce the electric field peak on the gate side, thus improving the breakdown voltage of the device. The prepared device with a gate length of 450 nm has a unit current gain cutoff frequency (fT) of 31.5 GHz, a maximum oscillation frequency (fMAX) of 46.3 GHz, and a three-terminal OFF-state breakdown voltage (BVgd) of 140 V at the gate-drain distance of 2.3 μm. The estimated Johnsonfs figure of merit (J-FOM=BVgd×fT) is 4.4 THz∙V, which is three and five times higher than that of the device with single HfO2 passivation layer and single SiO2 passivation layer, respectively. Furthermore, a significant suppression of the current collapse ( 5.7%) is observed due to the electric field redistribution near the drain region. The results show that the AlGaN/GaN HEMTs with stacked passivation layer proved to be a promising candidate for high-performance radio frequency (RF) power device applications.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 11, 130-134
Open AccessNovel Stacked Passivation Structure for AlGaN/GaN HEMTs on Silicon With High Johnson’s Figures of Merit
We present a high-performance AlGaN/GaN high electron mobility transistors (HEMTs) on silicon substrate with novel stacked passivation layer (HfO2/SiO2). The stacked passivation structure can effectively modulate the electric field and reduce the electric field peak on the gate side, thus improving the breakdown voltage of the device. The prepared device with a gate length of 450 nm has a unit current gain cutoff frequency (fT) of 31.5 GHz, a maximum oscillation frequency (fMAX) of 46.3 GHz, and a three-terminal OFF-state breakdown voltage (BVgd) of 140 V at the gate-drain distance of 2.3 μm. The estimated Johnsonfs figure of merit (J-FOM=BVgd×fT) is 4.4 THz∙V, which is three and five times higher than that of the device with single HfO2 passivation layer and single SiO2 passivation layer, respectively. Furthermore, a significant suppression of the current collapse ( 5.7%) is observed due to the electric field redistribution near the drain region. The results show that the AlGaN/GaN HEMTs with stacked passivation layer proved to be a promising candidate for high-performance radio frequency (RF) power device applications.
- Open Access
- 25 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 356-360
Effective Suppression of Current Collapse in AlGaN/GaN HEMT With N2O Plasma Treatment Followed by High Temperature Annealing in N2 Ambience
We propose a high temperature annealing process in N 2 ambience after N 2 O plasma treatment for AlGaN/GaN HEMT. The annealing process effectively improves the plasma treated surface condition and decreases the current collapse from 41.7% to 10.6%. The N 2 O plasma treatment is performed in a PECVD chamber and the followed high temperature annealing process is carried out at 800°C for 20min in rapid temperature annealing (RTA) system. Compared to the devices with only N 2 O plasma treatment, the devices with an extra high temperature annealing process perform lower surface state density (2.51E+12 cm −2 eV −1 , $\boldsymbol{\Delta }\text{E}$ from 0.353 eV to 0.413 eV; 5.38E+11 cm −2 , $\boldsymbol{\Delta }\text{E}$ > 0.519 eV) and better dynamic characteristics.
- 25 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 356-360
Open AccessEffective Suppression of Current Collapse in AlGaN/GaN HEMT With N2O Plasma Treatment Followed by High Temperature Annealing in N2 Ambience
We propose a high temperature annealing process in N 2 ambience after N 2 O plasma treatment for AlGaN/GaN HEMT. The annealing process effectively improves the plasma treated surface condition and decreases the current collapse from 41.7% to 10.6%. The N 2 O plasma treatment is performed in a PECVD chamber and the followed high temperature annealing process is carried out at 800°C for 20min in rapid temperature annealing (RTA) system. Compared to the devices with only N 2 O plasma treatment, the devices with an extra high temperature annealing process perform lower surface state density (2.51E+12 cm −2 eV −1 , $\boldsymbol{\Delta }\text{E}$ from 0.353 eV to 0.413 eV; 5.38E+11 cm −2 , $\boldsymbol{\Delta }\text{E}$ > 0.519 eV) and better dynamic characteristics.
- 11 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 42 (4) , 481-484
High Breakdown-Voltage GaN-Based HEMTs on Silicon With Ti/Al/Ni/Ti Ohmic Contacts
We propose the Ti/Al/Ni/Ti ohmic contacts to improve the breakdown voltage (V BD ) of GaN-based high electron mobility transistors (HEMTs). Using the same photolithography process, the first Ti/Al metal stack and the second Ni/Ti metal stack were achieved by electron beam (EB) evaporation and magnetron sputter, respectively. Attributed to the better particle filling on the sidewall by magnetron sputtering, the second Ni/Ti metal stack completely wraps the first Ti/Al metal stack and extends to both sides after a lift-off process. Even after high temperature annealing (HTA), the Ti/Al/Ni/Ti metal stack can keep smooth edge acuity and surface morphology, resulting in a uniform electric-field distribution near the ohmic contacts. Compared with Ti/Al/Ni/Au ohmic contacts, HEMTs with Ti/Al/Ni/Ti ohmic contacts have higher V BD and can improve the uniformity as well as repeatability of V BD .
- 11 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 42 (4) , 481-484
High Breakdown-Voltage GaN-Based HEMTs on Silicon With Ti/Al/Ni/Ti Ohmic Contacts
We propose the Ti/Al/Ni/Ti ohmic contacts to improve the breakdown voltage (V BD ) of GaN-based high electron mobility transistors (HEMTs). Using the same photolithography process, the first Ti/Al metal stack and the second Ni/Ti metal stack were achieved by electron beam (EB) evaporation and magnetron sputter, respectively. Attributed to the better particle filling on the sidewall by magnetron sputtering, the second Ni/Ti metal stack completely wraps the first Ti/Al metal stack and extends to both sides after a lift-off process. Even after high temperature annealing (HTA), the Ti/Al/Ni/Ti metal stack can keep smooth edge acuity and surface morphology, resulting in a uniform electric-field distribution near the ohmic contacts. Compared with Ti/Al/Ni/Au ohmic contacts, HEMTs with Ti/Al/Ni/Ti ohmic contacts have higher V BD and can improve the uniformity as well as repeatability of V BD .
- 28 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (12) , 5427-5433
A Comprehensive Analysis of the 2-DEG Transport Properties in In x Al1 – x N/AlN/GaN Heterostructure: Experiments and Numerical Simulations
A comprehensive investigation on the low-field 2-DEG mobility in InₓAl₁₋ₓN/AlN/GaN heterostructure has been made through Hall experimental and numerical calculation based on an ensemble Monte Carlo (MC) approach. Hall measurement on a lattice-matched (LM) In₀.18Al₀.82N/AlN/GaN heterostructure grown by metal-organic chemical vapor deposition (MOCVD) has been carried out as a function of temperature ranging from 77 to 405 K. A more rigorous model is presented taking both inter- and intra-subband scattering into account. The scattering rates are derived from the results of the electron density, the quantized energy levels, and the corresponding wave functions based on the self-consistent solutions of Poisson's and Schrödinger's equation given in our previous work. We confirm that the interface scattering process dominates the mobility within the low temperature (77-130 K), as increasing of the temperature, the highly inelastic scattering caused by partial occupation of the higher subband is responsible for the rapid degradation of the 2-DEG mobility. The role of surface morphology and indium fraction of the heterostructure on the dependence of the 2-DEG mobility have been clarified qualitatively in detail. The calculated results are widely compared with the published literature and our experimental finding. A reasonable agreement is achieved.
- 28 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (12) , 5427-5433
A Comprehensive Analysis of the 2-DEG Transport Properties in In x Al1 – x N/AlN/GaN Heterostructure: Experiments and Numerical Simulations
A comprehensive investigation on the low-field 2-DEG mobility in InₓAl₁₋ₓN/AlN/GaN heterostructure has been made through Hall experimental and numerical calculation based on an ensemble Monte Carlo (MC) approach. Hall measurement on a lattice-matched (LM) In₀.18Al₀.82N/AlN/GaN heterostructure grown by metal-organic chemical vapor deposition (MOCVD) has been carried out as a function of temperature ranging from 77 to 405 K. A more rigorous model is presented taking both inter- and intra-subband scattering into account. The scattering rates are derived from the results of the electron density, the quantized energy levels, and the corresponding wave functions based on the self-consistent solutions of Poisson's and Schrödinger's equation given in our previous work. We confirm that the interface scattering process dominates the mobility within the low temperature (77-130 K), as increasing of the temperature, the highly inelastic scattering caused by partial occupation of the higher subband is responsible for the rapid degradation of the 2-DEG mobility. The role of surface morphology and indium fraction of the heterostructure on the dependence of the 2-DEG mobility have been clarified qualitatively in detail. The calculated results are widely compared with the published literature and our experimental finding. A reasonable agreement is achieved.