Hamid Ranjkesh Adarmanabadi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hamid Ranjkesh Adarmanabadi has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Arezou Rasti
Department of Mineral Engineering, New Mexico Institute of Mining and Technology, Socorro, NM, USA
4 shared publicationsMehrdad Razavi
Department of Mineral Engineering, New Mexico Institute of Mining and Technology, Socorro, NM, USA
2 shared publicationsJesse Reinikainen
YeDoma Consultants LLC Company
1 shared publication- Maria Pineda
Department of AGRARIA, University of Reggio Calabria, Loc. Feo di Vito s.n.c., Reggio Calabria 89122, Italy
1 shared publication Mohammad Reza Sahlabadi
Department of Technical and Engineering, Islamic Azad University Science and Research Branch, Tehran, Iran
1 shared publicationMorteza Tabaei
Department of Mining Engineering, Isfahan University of Technology, Isfahan, Iran
1 shared publication
Latest Publications
- 3 March 2023
- Published by Taylor & Francis in Geomechanics and Geoengineering
- Vol. 19 (2) , 110-122
Effects of discontinuities on the rock block geometry of dimension stone quarries: a case study
The geometry of rock blocks, including shape and size, is a crucial factor affecting the quarry’s profitability. The block’s dimension is limited by the fracture network properties, especially discontinuity’s orientation, and spacing. Volumetric joint count (Jv), and weighted joint density (WJd) are two well-known indexes to determine the average block’s volume. In this investigation the discontinuity properties of eight quarries are determined through the line and aerial mapping surveys. The investigation was performed along 2258 m scanline in 63 slope benches. Different indexes were used to compare the obtainable rock block’s geometry. An empirical index was proposed considering different aspects of discontinuity network to increase the accuracy of measurements. The index was introduced based on the number of joints in each joint set, average spacing of joints in each joint set, and the total number of joints recorded during the investigation. The joint mean spacing index allows us to estimate the average volume of blocks and evaluate the quarry’s profitability. By increasing the ratio of the joint mean spacing index, the obtainable rock block’s volume and mine profitability increase.
- 3 March 2023
- Published by Taylor & Francis in Geomechanics and Geoengineering
- Vol. 19 (2) , 110-122
Effects of discontinuities on the rock block geometry of dimension stone quarries: a case study
The geometry of rock blocks, including shape and size, is a crucial factor affecting the quarry’s profitability. The block’s dimension is limited by the fracture network properties, especially discontinuity’s orientation, and spacing. Volumetric joint count (Jv), and weighted joint density (WJd) are two well-known indexes to determine the average block’s volume. In this investigation the discontinuity properties of eight quarries are determined through the line and aerial mapping surveys. The investigation was performed along 2258 m scanline in 63 slope benches. Different indexes were used to compare the obtainable rock block’s geometry. An empirical index was proposed considering different aspects of discontinuity network to increase the accuracy of measurements. The index was introduced based on the number of joints in each joint set, average spacing of joints in each joint set, and the total number of joints recorded during the investigation. The joint mean spacing index allows us to estimate the average volume of blocks and evaluate the quarry’s profitability. By increasing the ratio of the joint mean spacing index, the obtainable rock block’s volume and mine profitability increase.
- 7 February 2022
- Published by Taylor & Francis in International Journal of Geotechnical Engineering
- Vol. 16 (2) , 225-238
Long-term effects of Cement Kiln Dust (CKD) on erosion control of a soil slope
Cement kiln dust (CKD) is a significant fine powdery material generated from the Portland cement manufacturing process. The United States environmental protection agency (EPA) declared that using CKD is not harmful to humans' health and the environment. The primary usage of CKD is recycled back into the cement kiln as raw feed. CKD has various applications such as water treatment, waste disposal, agriculture, construction, soil stabilization, and erosion control of the natural or human-made slopes. An experimental study of CKD's effect on engineering properties was done on a natural slope in New Mexico, USA, in 2008. Consequently, Atterberg limits, compaction characteristics, unconfined compressive strength, and pH were determined for the native soil and the treated soil with CKD. Based on the result, it was observed that CKD was one of the cost-effective methods of erosion control of slopes. However, CKD's time and environmental effects are important factors that should be addressed carefully. This study mainly focuses on the influence of time on erosion control of the slope stabilized by CKD after eleven years. Long-term monitoring of the slope showed that CKD is still reducing soil erosion.
- 7 February 2022
- Published by Taylor & Francis in International Journal of Geotechnical Engineering
- Vol. 16 (2) , 225-238
Long-term effects of Cement Kiln Dust (CKD) on erosion control of a soil slope
Cement kiln dust (CKD) is a significant fine powdery material generated from the Portland cement manufacturing process. The United States environmental protection agency (EPA) declared that using CKD is not harmful to humans' health and the environment. The primary usage of CKD is recycled back into the cement kiln as raw feed. CKD has various applications such as water treatment, waste disposal, agriculture, construction, soil stabilization, and erosion control of the natural or human-made slopes. An experimental study of CKD's effect on engineering properties was done on a natural slope in New Mexico, USA, in 2008. Consequently, Atterberg limits, compaction characteristics, unconfined compressive strength, and pH were determined for the native soil and the treated soil with CKD. Based on the result, it was observed that CKD was one of the cost-effective methods of erosion control of slopes. However, CKD's time and environmental effects are important factors that should be addressed carefully. This study mainly focuses on the influence of time on erosion control of the slope stabilized by CKD after eleven years. Long-term monitoring of the slope showed that CKD is still reducing soil erosion.
- 1 January 2021
- Published by Faculty of Mining, Geology and Petroleum Engineering in Rudarsko-geološko-naftni zbornik
- Vol. 36 (4) , 21-32
EFFECTS OF CONTROLLABLE AND UNCONTROLLABLE PARAMETERS ON DIAMOND WIRE CUTTING PERFORMANCE USING STATISTICAL ANALYSIS: A CASE STUDY
Nowadays, most mining and quarrying industries utilize a diamond wire saw machine for bench cutting operations. This method uses a metal wire or cable assembled by diamond beads to cut the hard stone into large blocks. Many parameters...
- 1 January 2021
- Published by Faculty of Mining, Geology and Petroleum Engineering in Rudarsko-geološko-naftni zbornik
- Vol. 36 (4) , 21-32
EFFECTS OF CONTROLLABLE AND UNCONTROLLABLE PARAMETERS ON DIAMOND WIRE CUTTING PERFORMANCE USING STATISTICAL ANALYSIS: A CASE STUDY
Nowadays, most mining and quarrying industries utilize a diamond wire saw machine for bench cutting operations. This method uses a metal wire or cable assembled by diamond beads to cut the hard stone into large blocks. Many parameters...
- Open Access
- 1 January 2021
- Published by Science Publications in American Journal of Engineering and Applied Sciences
- Vol. 14 (1) , 129-138
Evaluating the Effect of Soil Particle Characterization on Internal Friction Angle
One of the critical design parameters used in evaluating soil structure is the friction angle, derived from Mohr's Circle failure criterion. The soil friction angle is an engineering parameter estimated in the laboratory to quantify the soil shear strength in geotechnical applications. This paper indicates an experimental study investigating the impact of particle size on different sandy soils shear strength behavior. The direct shear test equipment is useful for simulating various stress regimes to determine the soil strength by employing a slow moving lateral force to a consolidated sample along a shear plane. A series of direct shear tests were conducted to investigate the interface behavior of soil. Soil samples were selected from different locations in New Mexico, United States. The influence of soil particle size on the soil's shear strength behavior is discussed by performing a series of symmetric direct shear tests according to ASTM D3080 and analyzing the results. To minimize errors, electronic transducers were used to measure vertical and horizontal displacements. DS7 is geotechnical testing software controlling the test by utilizing a data logger. The investigation indicates that the maximum vertical deformation for all different kinds of sandy soils accrued simultaneously. It was concluded that a soil's friction angle is affected by coarse-grained material. Accordingly, sandy soils with bigger particle size record a higher friction angle than soils containing small particles. Furthermore, a non-linear regression analysis was performed to determine the direct relationship between soil's friction angle and soil particle characteristics.
- 1 January 2021
- Published by Science Publications in American Journal of Engineering and Applied Sciences
- Vol. 14 (1) , 129-138
Open AccessEvaluating the Effect of Soil Particle Characterization on Internal Friction Angle
One of the critical design parameters used in evaluating soil structure is the friction angle, derived from Mohr's Circle failure criterion. The soil friction angle is an engineering parameter estimated in the laboratory to quantify the soil shear strength in geotechnical applications. This paper indicates an experimental study investigating the impact of particle size on different sandy soils shear strength behavior. The direct shear test equipment is useful for simulating various stress regimes to determine the soil strength by employing a slow moving lateral force to a consolidated sample along a shear plane. A series of direct shear tests were conducted to investigate the interface behavior of soil. Soil samples were selected from different locations in New Mexico, United States. The influence of soil particle size on the soil's shear strength behavior is discussed by performing a series of symmetric direct shear tests according to ASTM D3080 and analyzing the results. To minimize errors, electronic transducers were used to measure vertical and horizontal displacements. DS7 is geotechnical testing software controlling the test by utilizing a data logger. The investigation indicates that the maximum vertical deformation for all different kinds of sandy soils accrued simultaneously. It was concluded that a soil's friction angle is affected by coarse-grained material. Accordingly, sandy soils with bigger particle size record a higher friction angle than soils containing small particles. Furthermore, a non-linear regression analysis was performed to determine the direct relationship between soil's friction angle and soil particle characteristics.